• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기설비전문위원
• /
• pp.79-81
• /
• 2007

To detect partial discharge of 154kV joint box, we have made experiment by using the Al-foil electrode sensor. Generally the signals which are detected in partial discharge test of underground power transmission cable are accompanied with both noises of high voltage and noises of surrounding power cable. The most noise in near to end part of joint box is corona, beside other noises flowed from surrounding area. Partial discharge test is difficulty due to these noises. First, we had used Al-Foil sensor on middle joint box of 154[kV] underground transmission power cable, and then analyzed reliability of calibration signal by using the Al-Foil electrode sensor of NJB. From above results, decrement properties measured highly. But incase of injecting calibration signal of 500[pC] after measuring signals in IJB, the S/N ratio had about 25[dB] acquisition.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1788-1790
• /
• 2003

GIS is a typical power equipment with higher reliability. It is compact and safe because all the energized parts are enclosed by a sealed cylindrical tank which is filled with $SF_6$. Generally gas insulated power equipments like GIS are designed to have sufficient electrical strength to prevent partial discharges under normal operating condition. Despite of the careful processes in manufacturing, transporting and assembling, voids or particles can be created, resulting in partial discharges at electrically weak points. The key factors causing partial discharges in GIS are; particles, voids in solid insulation, protrusions, poor contact of metal components, etc. The particle can be attached on; spacers, electrodes, internal wall of the GIS tank. It also moves in GIS freely. Most of partial discharges are likely to occur when particles are attached to spacers. In this paper, the electrical characteristics of a surface discharge were investigated under various conditions by using simulation program of FEMLAB.

• 전기학회논문지
• /
• 제63권10호
• /
• pp.1461-1466
• /
• 2014

GIS(Gas Insulated Switchgear) is important power apparatus which have strong dielectric strength, supply electric power and is a part of the power system. Most substation type is configured as GIS. Recently, because of continuous increasement of GIS demand resulted from high quality & big capacity of electric power, the necessity of the preventive & diagnosis system is being expanded gradually. GIS partial discharge occurred on the UHF band is detected effectively by the method to IEC 60270 that recommend to be able to detect the apparent minimum discharge, 5 pC. Additionally, the UHF sensor should be installed to detect PD signal if Partial discharge signal, 5 pC occur in every part of GIS. Currently PD diagnosis system applying UHF sensor for GIS with various voltage level like 154 kV, 345 kV, 765 kV have been operated. And it is necessary to measure and analyze insulation breakdown phenomenon of inside GIS exactly. In this paper, we proposed Fat-dipole patch UHF sensor that is developed and more sensitive, excellent wide-range characteristic than the exising UHF sensor. And we performed KERI (Korea Electrotechnology Research Institute) reference test, which showed the excellent result for the all tests.

• Steel and Composite Structures
• /
• 제39권1호
• /
• pp.109-123
• /
• 2021

This research endeavor intends to use the implicit finite element method to investigate the structural response of steel shear walls with partial plate-column connection. To this end, comprehensive verification studies are initially performed by comparing the numerical predictions with several reported experimental results in order to demonstrate the reliability and accuracy of the implicit analysis method. Comparison is made between the hysteresis curves, failure modes, and base shear capacities predicted numerically using ABAQUS software and obtained/observed experimentally. Following the validation of the finite element analysis approach, the effects of partial plate-column connection on the strength and stiffness performances of steel shear wall systems with different web-plate slenderness and aspect ratios under monotonic loading are investigated through a parametric study. While removal of the connection between the web-plate and columns can be beneficial by decreasing the overall system demand on the vertical boundary members, based on the results and findings of this study such detachment can lower the stiffness and strength capacities of steel shear walls by about 25%, on average.

• 한국안전학회지
• /
• 제34권1호
• /
• pp.53-61
• /
• 2019

This study performs reliability analysis of three-dimensional temporary shoring structures with three different models. The first model represents a field model which does not have diagonal bracing members. The installation of bracing members is often neglected in the field for convenience. The second model corresponds to a design model which has the bracing members with the hinge connection of horizontal and bracing members at joints. The third model is similar to the second model but the hinge connection is replaced with partial rotational stiffness. The reliability analysis results revealed that the vertical members of the three models are safe enough in terms of axial force, but the vertical and horizontal members exhibit a big difference among the three models in terms of combination stress of axial force and bi-axial bending moments. The field model showed significant increase in failure probability for the horizontal member, and thus the results demonstrate that the bracing member should be installed necessarily for the safety of the temporary shoring structures.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제7권4호
• /
• pp.137-148
• /
• 2007

Rapid increase of embedded systems in electronic and mechanical control systems requires reliable and error-free embedded software. State-based testing methods like FSM are usually used to assure the reliability of embedded software. However, because of possibility of explosion of test cases, only partial test cases are considered in practical tests, which cannot guarantee that all the possible errors are investigated. This study proposes a test procedure based on failure mechanisms that may occur in embedded systems, which can not only assure that certain kinds of possible errors are detected but reduce the testing time. The proposed procedure is applied to vehicle air control system.

• 한국정밀공학회지
• /
• 제26권7호
• /
• pp.81-90
• /
• 2009

Due to environmental issues, the development of low energy consumption products has become one of the main topics in the home appliance industry. The energy consumption of a refrigerator depends on the efficiency of its compressor as well as on the refrigerator cycle design, such as the capacity modulation. In this study, a dual capacity, i.e., two-step capacity modulation (TCM), reciprocating compressor is developed. In a TCM compressor, capacity modulation is achieved by changing the dead volume in the cylinder. Instead of a concentric sleeve, an eccentric sleeve, a key, and a spring are used to change the dead volume for the clockwise and counterclockwise rotation of a motor. When the compressor changes its operating mode from full capacity to partial capacity or in opposite direction, the key may collide with the eccentric sleeve. The structural reliability and mode change reliability were confirmed by analysis and experiment.

• International Journal of Reliability and Applications
• /
• 제7권1호
• /
• pp.41-53
• /
• 2006

The exact cause of the system's failure is often unknown in the masked system lifetime data. In such type of data, there are two observable quantities, namely (i) the systems time to failure and (ii) the set of systems components that contains the component, which might cause the system to fail. Our objective in this paper is to use the maximum likelihood procedure in the presence of masked data to make inference for the reliability of the system's components. We assume a multi-component series system where each component has a constant failure rate. Different cases that permit for closed form solutions of point estimates are considered. The results obtained in this paper generalize other published results.

• 한국안전학회지
• /
• 제12권4호
• /
• pp.180-190
• /
• 1997

A new method in the fault tree analysis (FTA) for the reliability calculation is suggested. Two steps are necessary in traditional method in evaluation of the occurrence probability of top event in fault tree (FT). The first step is to find the minimal outsets, and the second one is to substitute the result into the poincare equation. In order to reduce the enormous computing time of this method, lots of rapid algorithms have been developed. Almost of all achievements were, however, based on the partial structural properties of FT. In this paper, the FT is transformed to a non-linear graph G which has the same minimal outsets of original n, and then the reliability is calculated using the domination theory. In this new method, the required number of equation terms are at most $2^n$ (n is node number of graph G), while $2^m$-1 (m is the number of minimal cutsets) calculation terms are required in the poincare equation in traditional method. Since m>>n in general. our new method reduces the calculation time significantly.

• 한국도로학회논문집
• /
• 제5권1호
• /
• pp.1-10
• /
• 2003

도로포장 설계의 목적은 다른 토목구조물의 설계와 마찬가지로 정해진 신뢰성 수준에서 가장 경제적인 설계를 얻는데 있다 할 것이다. 미국과 유럽의 선진국가들의 설계법들은 전혀 상이한 신뢰성 수준을 갖는 설계결과들을 생산하는 설계법을 지양해가면서 세월을 두고 변천하여 균등한 신뢰성 수준을 보장할 수 있는 LRFD양식을 채용하는 방향으로 발전되었다. 현재, LRFD 양식은 콘크리트 구조, 목구조, 강구조 및 교량설계기준에 적용되어 있다 본 논문에서 저자는 역학-경험적 포장설계법에 적용될 신뢰성 모듈의 한 대안으로 신뢰성이론을 사용하여 LRFD 양식을 개발하고자 하는 과정을 예시하였다. AASHTO 86설계법에 따라 동일한 신뢰성 수준을 갖도록 설계된 10개의 포장단면이 피로균열과 같은 역학적 포장손상 측면에서 볼 때 균등한 구조적 신뢰성을 보여주지 못하며 LRFD 양식을 사용함으로서 그러한 균등한 신뢰성을 확보할 수 있다는 사실이 본 논문을 통해 예시되고 있다.