• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.2
• /
• pp.65-71
• /
• 2014

SMF9060 material is a Fe-based powder sintered alloy that is used for several automobile components such as Synchronize Hub, oil pump and transmission. These components are required excellent wear resistance and durability. In this study, we have performed a dry wear test at the ambient air and Ar gas conditions in the room temperature, and a lubricant wear test at the room temperature and engine oil temperature of $100^{\circ}C$. The amount of wear volume and coefficient friction are measured by a Profilometer and a Ball on disk type wear tester. The wear volume in Ar gas condition was a little higher than that in the ambient air condition. However the wear volume in the lubricant wear condition was much lower than in the dry wear condition. XRD analysis of the debris in Ar gas condition showed that the oxide film was not formed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.105-111
• /
• 2008

The clutch with torsional damper is installed on a passenger car with manual transmission, which not only transmits the power generated by engine to the transmission but also absorbs the shock and vibration from the engine. The torsional damper in the clutch dissipates the torsional vibration energy and eliminates the resonance in the driveline but high damping in the damper causes the increase of the vibration level which is against the comfort and durability. In this study, a dynamic model for the passenger car driveline with manual transmission was developed to investigate the vibration and the effects of characteristics of the driveline. With the dynamic model, the vibration characteristics of driveline were examined by the mode analysis and driving simulation, and the effects of hysteresis torque and spring constant were investigated. The vehicle tests with prototype torsional dampers were preformed and the test results showed good agreements with the simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.816-821
• /
• 2005

The cycloid reducer has very high efficiency, high ratios, high stiffness and small size, in comparison with a conventional gear mechanism, which makes it an attractive candidate for limited space and precision application such as industrial robot. There are several publications on analysis and design of the cycloid reducer, however, it was assumed that the contact stiffness of pin rollers and cycloid disk is constant regardless of their contact geometry. Moreover, the torsional stiffness of the cycloid reducer couldn't be calculated due to the assumption. In this paper, we present a new procedure of calculating torsional stiffness of the cycloid reducer using Hertz contact theory. First, conventional force analysis of the cycloid reducer is briefly reviewed. Then, iterative numerical calculation procedure of the contact stiffness is proposed based on the Hertz contact theory where the contact stiffness depends on the contact force. In addition, total torsional stiffness of the cycloid reducer is estimated considering its rolling element bearing stiffness. The torsional stiffness of the cycloid reducer is dominated by the rolling element bearing stiffness since the contact stiffness of the cycloid disk is too large.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.7
• /
• pp.599-604
• /
• 2011

A highly strained nanostructure comprising crystallographically aligned HgTe nanoinclusions and a surrounding PbTe matrix has been synthesized using a precipitation process of supersaturated HgTe-PbTe alloys. From the early precipitation stage, HgTe nanoinclusions take disk shape, which is transformed from initial HgTe nuclei, although there is no lattice constant difference of the two end components at standard state. As a primary reason for the morphological transformation of the initial spherical HgTe nuclei to HgTe nanodisks, the induced lattice mismatch is suggested. On the condition that the HgTe nanodisks maintain perfect coherent nature with PbTe matrix, the stress-free lattice constant of constrained HgTe nanodisks has been calculated based on the defined concept of the strain-induced tetragonality, the linear elasticity and the actual measurement in HRTEM images.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.6
• /
• pp.1753-1765
• /
• 2000

As the areas of computer application are expanded, real-time application environments that must process as many transactions as possible within their deadlines, such as a stock transaction systems, ATM switching systems etc, have been increased recently. The reason why the conventional database systems can't process soft real-time applications is the lack of prediction and poor performance on processing transaction's deadline. If transactions want to access data stored at the secondary storage, they can not satisfy requirements of real-time applications because of the disk delay time. This paper designs a main-memory database prototype systems to be suitable to real-time applications and then this system can produce rapid results without disk i/o as all of the information are loaded in main memory database. In thesis proposed the improved techniques with respect to logging, checkpointing, and recovering in our environment. In order to improve the performance of the system, a) the frequency of log analysis and redo processing is reduced by the proposed redo technique at system failure, b) database consistency is maintained by improved fuzzy checkpointing. The performance model is proposed which consists of two parts. The first part evaluates log processing time for recovery and compares with other research activities. The second part examines checkpointing behavior.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.5
• /
• pp.672-677
• /
• 2010

The goal of this study is to simplify the measurement process of the flat zone length produced by a flexible disk grinding system for the process automation. The image of workpiece in the grinding process is obtained, and the cutting speed and the feeding speed are controlled carefully to maximize the flat zone length. The gradient, the inflection point and the length of the line in the image are calculated, and the length is also measured by using a projector. Processing conditions and inversely proportional to flat zone length was changing. The flat zone length is estimated by Neural network algorithm considering the process conditions with the estimated error range as 0.06~3.61%, the Neural network algorithm for the grinding process estimation is found to be useful for building the process automation database.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.27 no.2
• /
• pp.204-212
• /
• 2017

The rotor dynamics and balancing technic for rotating equipment during engineering and manufacture stage are to be carefully considered in order to minimize the operation troubles regarding vibration during commissioning stage. In this paper, the test rig, which includes the disks as balancing plane, is designed and manufactured, so that the characteristic of rotor dynamics can be analyzed such as critical speed and mode shape. The critical speed predicted through natural frequency analysis is verified by the actual measurement on bearing housing vibration during start-up condition of test rig. The low speed balancing and the operating speed balancing test are performed respectively with consideration of first critical speed, and the residual unbalance amounts are estimated in accordance with the relevant method described in API standard. In addition, the single and dual plane balancing are carried out on main disk and trim disk depended on phase information at each balancing step.

• Design & Manufacturing
• /
• v.7 no.1
• /
• pp.28-33
• /
• 2013

During the cold forming, due to high working pressure acting on the die surface, failure mechanics must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. The mechanisms of wear are consisted of adhesion, abrasion, erosion and so on. Die wear affects the tolerances of formed parts, metal flow, and costs of process. The only way to control these failures is to develop a prediction method on die wear suitable in the design state in order to optimize the process. The wear system is used to analyse 'operating variables' and 'system structure'. In this study, with AISI D2, AISI 1020, AISI 304SS materials, a series of the wear experiments of pin-on-disk type to obtain the wear coefficients from Archard's wear model and the upsetting processes are carried out to observe the wear phenomenon during the cold forming process. The analysis of upsetting processes are performed by the rigid-plastic finite element method. The result of the analysis is used to investigate the die wear the processes, and the analysis simulated die wear profiles are compared with the experimental measured die wear profiles.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.12
• /
• pp.958-962
• /
• 2009

Flash memory, which replaces hard disk recently, has different physical characteristics with hard disk. For the performance of flash memory based storage system, many researches over OS and file system layers has been doing. In this paper, we propose the architecture of flash memory based storage which uses information of page invalidation when file deletion occurs from upper layer. Also, we evaluate the performance of proposed system. Proposed system effectively increases IO performance by using page invalidation information to block merge and wear leveling algorithms.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.2
• /
• pp.39.1-39.1
• /
• 2016

We report the discovery of a kiloparsec-size supershell in the outskirts of the Milky Way with the compact high-velocity cloud, HVC 040+01-282 (hereafter, CHVC040), at its geometrical center using the "Inner-Galaxy Arecibo L-band Feed Array" HI 21 cm survey data. Supershells are large gaseous shells, which could be produced by one of most energetic activities with an explosion energy more than $3{\times}1052erg$. The most promising origin is the explosion of multiple supernovae in OB associations, or alternatively, the impact of HVCs falling into the Galactic disk. We found the association between CHVC040 and the Galactic supershell by analysis of their morphological and physical properties. Our results imply that some compact HVCs can survive their trip through the Galactic halo and inject energy and momentum into the Milky Way disk.