• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.352-354
• /
• 2004

In this paper, a parallel fuzzy controller for one degree of freedom magnetic levitation is designed and its performance is compared with the performance of a PID controller. Input, output scaling factor of fuzzy controller and gain of PID controller were tuned using the GA algorithm. The designed controllers are validated by numerical simulations. So it's shown that parallel fuzzy controller can give the better performance for the plant than PID controller.

• International Journal of Control, Automation, and Systems
• /
• 제5권5호
• /
• pp.559-569
• /
• 2007

In this paper, the dynamic controller design problem of a redundant planar 2-dof parallel manipulator is studied. Using the Euler-Lagrange equation, we formulate the dynamic model of the parallel manipulator in the joint space and propose an augmented PD controller with forward dynamic compensation for the parallel manipulator. By formulating the controller in the joint space, we eliminate the complex computation of the Jacobian matrix of joint angles with end-effector coordinate. So with less computation, our controller is easier to implement, and a shorter sampling period can be achieved, which makes the controller more suitable for high-speed motion control. Furthermore, with the combination of static friction model and viscous friction model, the active joint friction of the parallel manipulator is studied and compensated in the controller. Based on the dynamic parameters of the parallel manipulator evaluated by direct measurement and identification, motion control experiments are implemented. With the experiments, the validity of the dynamic model is proved and the performance of the controller is evaluated. Experiment results show that, with forward dynamic compensation, the augmented PD controller can improve the tracking performance of the parallel manipulator over the simple PD controller.

• 제어로봇시스템학회논문지
• /
• 제5권3호
• /
• pp.288-296
• /
• 1999

A force-reflecting hand controller can provide the kinesthetic information obtained from a slave manipulator to the operator of a teleoperation system. The goal is to construct a compact hand controller that can provide large workspace and good force-reflecting capability. This paper presents the design and the analysis of a 6-degree-of-freedom force-reflecting hand controller using fivebar parallel mechanism. The forward kinematics of the fivebar parallel mechanism has been calculated in real-time using three pin-joint sensors in addition to six actuator position sensors. A force decomposition approach is used to compute the Jacobian. To evaluate the characteristics of the fivebar parallel mechanism, it has been compared with the other three parallel mechanisms in terms with workspace and manipulability measure. The hand controller using the fivebar parallel mechanism has been constructed and tested to verify the feasibility of the design concept.

• 제어로봇시스템학회논문지
• /
• 제9권5호
• /
• pp.379-383
• /
• 2003

Parallel type fuzzy controller is designed by using a hybrid connected type fuzzy-PID controller and a model reference fuzzy controller. The first controller, consists of a fuzzy-PI and a fuzzy-PD making a hybrid type fuzzy-PID controller, plays a role as firstly reaching stable responses and secondly overcoming disturbance in plants. The second controller, model reference fuzzy controller, plays a role as reaching faster responses than other controllers. We have confirmed that the controller produces rapid and stable responses and overcomes disturbance by using parallel type fuzzy controller in a DC motor application.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 B
• /
• pp.665-668
• /
• 2003

In this paper, we have designed and implemented the RAID controller board which connects to the host computer with serial ATA interface and connects to the disks with parallel ATA interface. Serial ATA interface is proposed to overcome the design limitation of parallel ATA while enabling the storage interface to scale with the slowing media rate demands for PC platforms. Serial ATA is to replace parallel ATA with the compatibility with existing operating systems and drivers, adding performance headroom for years to come. It Moreover, serial ATA provides even faster transfer rate of 150 Mbytes/s which is larger than that of current parallel ATA. The RAID controller board designed in this paper combines up to 4 disks with parallel ATA interface, and connects to PC host computer with serial ATA interface. We have implemented RAID controller using Verilog HDL language with FPGA chip. The RAID controller supports RAID level 0 and 1 functionality. Experimently, the average read/write performance of parallel ATA interface is about 30 Mbytes/s. Therefore, when 4 parallel disks is connected to the RAID controller board, we can get almost full throughput of serial ATA protocol using the RAID level 0 configuration with 4 disks.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1545-1548
• /
• 1997

A Force-refecting hand controller can provide the kinesthetic information obtained from a slave manipulator to the operator of a teleoperation system. This thesis presents the desgn and the analysis of a 6-degree-of-freedom force-reflecting hand controller using fivebar parallel mechanism. The goal of this thesis is to construct a superior hand controller that can provide large workspace and good force-reflecting ability. The forward kinematics of the fivebar paprallel mechanism has been calculated in real-time using three pin-joint sensors in addition to six actuator position sensors. A force decomposition approach is used to comput the Jacobin. To analyze the characteristics of the fivebar parallel mechanism, it has been compared with the other three parallel mechanisms in terms with workspace and manipulability measure. The force-reflecting hand controller using the fivebar parallel mechanism has been constructed and tested to verify the feasibility of the design concept.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2002년도 추계종합학술대회
• /
• pp.888-892
• /
• 2002

본 논문에서는 Hybrid형 퍼지-PID 제어기와 모델참조 퍼지제어기를 이용하여 병렬형 퍼지 제어기를 설계 하였다. 먼저 첫 번째 제어기는 퍼지 PI와 퍼지 PD가 결합한 Hybrid형 퍼지-PID 제어기로서 원하는 응답특성에 대해 안정하게 도달하는 목적과 플랜트에 대해 외란이 발생한 경우 외란을 극복할 수 있는 역할을 하게 된다. 그리고 두 번째 제어기인 모델참조 퍼지제어기는 원하는 응답에 대해 빠른 응답을 나타낼 수 있도록 설계하였다. 본 논문에서 설계된 병령형 퍼지제어기를 이용하여 DC 모터에 적용하여 응답특성을 살펴본 결과 빠르고 안정된 응답특성과 또한 외란이 발생한 경우 빠른 시간에서 외란을 극복함을 확인하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1996년도 창립기념 전력전자학술발표회 논문집
• /
• pp.56-59
• /
• 1996

In this paper, we developed a micro-stepping drive circuit of step motor and proposed software algorithm for parallel operation of step motors drived by micro-stepping circuit. Also, we implemented a parallel operation controller with a 16-bit micro-controller.

• 전기학회논문지
• /
• 제67권6호
• /
• pp.738-744
• /
• 2018

This paper proposes a low cost hot swap operation circuit of a parallel operation power supply for servers. Hot swap function for server power system is essential in 24 hour operation system such as internet data center, server, factory and etc. Server power supplies used in internet data centers have two or more parallel operations with the hot swap operation. However, the cost of the power supply is high because the controller IC for hot swap operation is very expensive. Therefore, this paper proposes a parallel-operated power supply with a low-cost hot swap controller for servers. The proposed system can operate hot swap function by using discrete devices and reduce the cost by more than 50%. A 1.2kW prototype system is implemented to verify the proposed low cost hot swap controller.

• 산업기술연구
• /
• 제21권A호
• /
• pp.97-103
• /
• 2001

This paper presents the development of the I/O Interface for the real time parallel data communication between controller of a six-axis industrial robot(CRS-A460) and an external computer. The proposed I/O Interface consists of the hardware I/O interface and the software that is downloaded to the robot controller and executed by the controller operating system. The constitution of the digital I/O Port for CRS-A460 robot controller and the digital I/O board for IBM-PC are presented as well as the Process Control Program of the robot controller. The developed protocol for the parallel data communication is described. The data communication is tested, and the performance is analysed. In particular, it is shown that the real-time constraint of the robot controller process is satisfied.