• Journal of Environmental Science International
• /
• v.16 no.11
• /
• pp.1225-1230
• /
• 2007

The emissions characteristics of particulate matters(PM) according to the types of wastes from industrial waste incinerator of 800 kg/hr treatment capacity were investigated. For this study, the incinerate waste are as follows; waste resin, waste wood, waste urethane, waste gunny, and waste paper. The particulate samples were collected to be emitted in stack and air pollution control(both cyclone and bag filter). In stack, the concentrations of PM were in the range of 2.61 to $26.51 mg/Sm^3$ and the major chemical species were C, Si, Cl, K, Na, Ca in all the wastes. In cyclone fly ash, the mean content of heavy metal were in the order of Fe > Zn > Pb > Cu > Mn > Cr > Ni > Cd > As > Hg and the heavy metal content of waste resin were Zn 34,197.5 mg/kg, Fe 27,587.6 mg/kg, Pb 6,055.8 mg/kg, respectively. In bag filter fly ash, the mean content of heavy metal were in the order of Zn > Pb > Fe > Cu > Mn > Cd > Cr > Ni > As > Hg and the heavy metal content of waste wood were Pb 36,405.2 mg/kg, Fe 15,762.9 mg/kg, Cu 9,989.5 mg/kg, Cd 2,230.1 mg/kg, respectively. Comparing the heavy metal content of both cyclone and bag filter, in cyclone, the Cr, Fe, Ni content were higher than in bag filter and the Cd, Cu, Hg content were lower than in bag filter.

• New & Renewable Energy
• /
• v.18 no.3
• /
• pp.23-31
• /
• 2022

This study evaluated the potential of coffee waste (CW) and used frying oil (UFO) as an additive in the production of pitch pine (PIP) and Mongolian oak (MOK) pellets. Ash contents obtained from CW and UFO were 0.5% and <0.1%, respectively. The calorific values of UFO (31.4 MJ/kg) and CW (26.3 MJ/kg) are higher than PIP (20.6 MJ/kg) and MOK (19.1 MJ/kg). For pellets fabricated using a pilot-scale flat-die pellet mill, regardless of fabricating conditions, moisture content (MC) and bulk density of PIP and MOK pellets satisfied the A1 wood pellet standard for residential and small-scale commercial uses, as designated by the National Institute of Forest Science (NIFOS) of the Republic of Korea. When CW was used as an additive, durability of PIP pellets made with 12%-MC sawdust and MOK pellets increased. The optimal conditions for producing PIP and MOK pellets could be by adding 20 mesh CW as an additive and the using of 12%-MC sawdust. However, durability of PIP pellets and ash content MOK pellets did not satisfy the A1 wood pellet standard of NIFOS. Thus, further research is needed to improve the properties of wood pellets with additives.

• Geomechanics and Engineering
• /
• v.28 no.3
• /
• pp.255-263
• /
• 2022

Lime stabilization has conventionally been listed amid the key techniques of chemical stabilization. Replacing lime with sustainable agro-based by-products have gained prominence in recent decades. Bagasse ash (BA) is one such potential alternatives, an industrial waste with abundance in production, and industries exploring sustainable solutions for its safe disposal. Supplementing BA with lime could be an ideal approach to reduce lime consumption. However, suitability of BA and lime for the stabilization of expansive clays, such as black cotton (BC) soil is yet to be explored. This paper therefore aims to investigate the suitability of BA-lime mixtures to stabilize BC soil with emphasis to compaction behaviors and unconfined compressive strength (UCS) using standard laboratory procedures. Suitability of BA-lime mixture is then assessed against addition of calcium sulphate which, from previous experience, is detrimental with lime stabilization. Experimental outcomes nominate 15% BA as the optimum value observed from both compaction and UCS data, while addition of 4% lime to 15% BA showed the best results. Mineralogical and microstructural analysis show the presence of cementitious compounds with addition of lime and calcium sulphate with curing periods. While, formation of Ettringite needles were noted with the addition of calcium sulphate in BA-lime mixtures (at optimum values) after 90-day curing, and UCS results showed a decrease at this point. To this end, addition of BA in lime stabilization showed encouraging results as assessed from the compaction and UCS results. Nonetheless usage of calcium salts, with utmost emphasis on calcium sulphate and equivalent should be avoided.

• Advances in nano research
• /
• v.16 no.3
• /
• pp.217-229
• /
• 2024

This paper presents results of visual analysis of cracks formation and propagation of concretes made of quaternary binders (QBC). A composition of the two most commonly used mineral additives, i.e. fly ash (FA) and silica fume (SF) in combination with nanosilica (nS), has been proposed as a partial replacement of the cement. The principal objective of the present study is to achieve information about the effect of simultaneous incorporation of three pozzolans as partial replacement to the OPC on the fracture processes in concretes made from quaternary binders (QBC). The modern and precise non-contact measurement method (NCMM) via digital image correlation (DIC) technique was used, during the studies. In the course of experiments it was established that the substitution of OPC with three pozzolans including the nanoadditive in FA+SF+nS FA+SF+nS combination causes a clear change of brittleness and behavior during fractures in QBCs. It was found that the shape of cracks in unmodified concrete was quasi-linear. Substitution of the binder by SCMs resulted in a slight heterogeneity of the structure of the QBC, including only SF and nS, and clear heterogeneity for concretes with the FA additive. In addition, as content of FA rises throughout each of QBC series, material becomes more ductile and shows less brittle failure. It means that an increase in the FA content in the concrete mix causes a significant change in fracture process in this composite in comparison to concrete with the addition of silica modifiers only.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.4
• /
• pp.82-90
• /
• 2009

It is very important to utilize effectively fibrous waste paper in terms of cost savings, environmental effects, and governmental policies. The quality of final products and runnability of papermaking process are primarily affected by constitutions of fibrous raw materials. In specific, board grade paper depends directly on compositions of waste paper bales. At present, the raw materials of board grade paper are mainly derived from lots kinds of wastepaper. Some papermaking countries, like EU, USA and Japan have advanced classification and management systems of recycled fiber, but Korea has not yet organized systematically. In this study, evaluation of wastepaper bale compositions and their fiber properties were carried out for effective utilization of fibrous raw materials for board grade paper production. 3 kinds of wastepaper bales were classified to fibrous or non-fibrous materials. In case of fibrous materials, KOCC, kraft sack paper and white duplex board matters were main component in total weight basis, and in case of non-fibrous materials, vinyl, plastic and cloth matters were main component, in turns. 3 representative kinds of waste paper were disintegrated and classified, and then prepared to handsheet for evaluation of recycled fiber property. Consequently, fines and ash content of waste paper, isolated from KOCC and white duplex board were higher than that of kraft sack paper. pH values of all kinds of waste fibers were neutral or weak alkaline.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.4 s.117
• /
• pp.1-9
• /
• 2006

Increasing the filler content of sheet provides an opportunity for saving production cost through fiber replacement with relatively low-priced filler. But increasing the filler content tends to decrease the strength of paper and filler retention. To overcome these problems, preflocculation technology of fillers has been suggested. To evaluate the effect cationic polymers on the size and size distribution of preflocculated GCC and their shear stability, cationic PAM and cationic starch were used. Results showed that cationic PAM formed large prefloc at low dosage. It was required to add 15 times as high as cationic starch to cationic PAM to obtain the same size prefloc. But preflocs formed with cationic starch was superior in shear stability to those formed with cationic PAM. With the increase of shear rate the size of preflocs decreased. Greater amount of small preflocs or un-flocculated fillers was observed when the dosage of polymers was low and this ended up low ash retention in handsheets.

• Journal of the Korean Society of Tobacco Science
• /
• v.19 no.1
• /
• pp.51-56
• /
• 1997

This experiment was conducted to reduce the cost of orient leaf using izmir, samsun and basma scraps in cigarettes manufacturing process. We manufactured rolled and paper sheet tobacco using orient scraps and substituted orient leaf in Pine tree to the rolled and paper sheet tobacco using orient scraps. Orient scraps were lower in total sugar, total sugar/nicotine and total nitrogen/nicotine, higher in nicotine and crude ash than those of orient leaves. Izmir and basma scraps were higher of 2-methyl butanoic, 3-methyl butanoic and 3-methyl pentanoic acid, but the chemical contents in samw scraps were lower than those of orient leaves. The specific gravity thickness, flness index, filling value were similar between orient scraps blended sheet tobacco and present sheet tobacco. The physical characteristics of orient scraps blended sheet tobacco were within Present sheet tobacco quality specification. The sheet tobacco using orient scraps was higher 2-metal butanoic, 3-methyl butanoic and 3-methyl pentanoic acid than those of present sheet tobacco. The rolled processed sheet tobacco using orient scraps was higher 2-methyl butanoic, 3-methyl butanoic and 3-methyl Pentanoic acid than those of paper sheet tobacco using orient scraps. The sample cigarettes using orient scraps sheet tobacco were lower 2-methyl butanoic, 3-mettwl butanoic and 3-mettwl Pentanoic acid than those of control cigarettes. The result of sensory test showed no great difference compared with sample of orient scraps and control cigarettes. This result shows that we can possible to substitute orient leaf to orient scraps to reduce the cost of orient leaf.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.3
• /
• pp.258-267
• /
• 2017

In this study, pitch pine (Pinus rigida, PIR) and Mongolian oak (Quercus mongolica, QUM) pellets were fabricated with bark or/and drying waste liquor (DWL) of larch (Larix kaempferi, LAK) as an additive. Based on the results of fuel characteristics of the pellets, optimal conditions for producing the high-quality pellets were provided. In the analysis of chemical composition, bark contained holocelluose and lignin of 90% and over. DWL had 0.1% solid assumed to sugars which are generated from the oven-drying of LAK logs. QUM showed high ash content (2.2%) by containing of bark in the sawdust. Bark and DWL of LAK had high ash content of 4% and over. Calorific values of all specimens and additives were higher than that of the $1^{st}$-grade standard of wood pellets designated by NIFOS (18.0 MJ/kg). PIR and QUM pellets were fabricated with additive of 2 wt% based on the solid weight of oven-dried sawdust using a piston-type flat-die pelletizer, and thus ash content and calorific value of the pellets did not affect by the use of additive. Durability of the pellets increased with the use of additive. Durabilties of pellets, which were fabricated with bark as an additive and DWL as a controller of moisture content for sawdust, did not differ from those of pellets without additives and were lower than those of pellets either with bark or DWL. However, use of both bark and DWL for the production of wood pellets might be favorable because it can make a profit from the collection process of DWL. Based on the results of fuel characteristics of the pellets, QUM and PIR pellets were produced by a flat-die pelletizer. Moisture content (MC), bulk density and durability of the pellets improved with the use of additive. Particularly, sawdust MC of 10% and the addition of bark or DWL for PIR as well as sawdust MC of 12% and the addition of bark for QUM might be optimal conditions for the production of high-quality pellets. Except for the ash content of QUM pellets, other properties of PIR and QUM pellets exceeded the $1^{st}$-grade wood pellets standards of NIFOS.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.1
• /
• pp.93-101
• /
• 2015

The purpose of this study is to examine the reusability of the fluff pulp recycled from paper diaper. To do this, the physical and optical properties of each handsheet made from these fluff pulp sample as well as the properties of the fiber recycled from paper diaper were analyzed and compared with those of non-recycled diaper fluff pulp samples and conventional pulp samples. These comparisons show that the characteristics of fiber such as length, width, curl, kink of the pulp recycled from paper diaper were similar to those of non-recycled diaper fluff pulp as well as to those of commercial pulp. The fine content of recycled diaper fluff pulp was lower than that of other pulp samples, while the ash content of the former was higher than that of the latter. Furthermore, it was also found that the bulk of handsheets made from the recycled fluff pulp was higher than that of other pulp samples, while the formation of the former was worse than that of the latter. The mechanical properties of the handsheet sample made from the recycled diaper fluff pulp was higher than those of the unused diaper fluff pulp and was lower that those of commercial fluff pulp and softwood tissue pulp handsheet. But, it was higher than that of hardwood tissue pulp handsheet. The optical properties of recycled diaper fluff pulp handsheet was lower than those of each handsheet samples made from other pulps due to its low fine content.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.2
• /
• pp.57-65
• /
• 2011

Pulping of paper mulberry (Broussonetia kazinoki) white bast has been examined by novel atmospheric pressure pulping methods. The viscosity of pulp has been found to be highly sensitive and variable with pulping methods. Therefore, selections of pulping chemicals and conditions are very important. Two kinds of pulping procedures were employed for the high viscosity pulp manufacturing. The one is ammonium oxalate treatment and the other is sodium chlorite and acetic acid treatment. Not only chemical components and pulp yields which of paper mulberry white bast but also water retention value (WRV), whiteness index, yellowness index, and colors of every pulp were examined. The hot water, 1% NaOH, and ethanol-benzene extractives which of paper mulberry white bast were 4.48%, 28.45%, and 2.84%, respectively. The contents of holocellulose, lignin, and ash were 90.66%, 1.05%, and 2.18%, respectively. In the pulp yields, group 1 which treated with only ammonium oxalate were 77.04-81.71%, group 2 which treated with ammonium oxalate and acidified sodium chlorite separately and washed between first and second stages were 64.15-83.90%, group 3 which treated with ammonium oxalate and acidified sodium chlorite separately and not washed between first and second stages were 57.35-73.17%, and group 4 which treated with mixed ammonium oxalate and acidified sodium chlorite were 66.58-68.43%. The pulps treated with acidified sodium chlorite showed high whiteness index, but the pulps treated with only ammonium oxalate showed high yellowness index. Variations in the combinations of treatments resulted in different pulp characteristics.