• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.97-103
• /
• 1993

This paper presents a quasi-analytical method using integral equations to obtain head distributions in unsaturated porous media with different hydrogeologic properties. One-dimensional soultion algorithms were developed for two cases of boundary conditions at the top: 1) constant head and 2) constant flux. Water table elevation at the bottom was assumed known for both cases. The methodology was applied to a fly ash disposal facility in an alluvium area. The results showed that the pressure head distributions had high nonlinearity with large gradients slightly above the interface of two media which made preliminary numerical solutions implausible. The developed method helped to structure finite element grids for improving convergence and accuracy.

• KIISE Transactions on Computing Practices
• /
• v.20 no.11
• /
• pp.610-614
• /
• 2014

Like many types of scientific data, results from simulations of volcanic ash diffusion are of a clustered sparse matrix in the netCDF format. Since these data sets are large in size, they generate high storage and transmission costs. In this paper, we suggest a new method that reduces the size of the data of volcanic ash diffusion simulations by converting the multi-dimensional index to a single dimension and keeping only the starting point and length of the consecutive zeros. This method presents performance that is almost as good as that of ZIP format compression, but does not destroy the netCDF structure. The suggested method is expected to allow for storage space to be efficiently used by reducing both the data size and the network transmission time.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.643-646
• /
• 2005

This paper reports the influence of super retarding agent(SRA) on the setting time of concrete incorporating mineral admixture including fly ash(FA), expansive additive(EA), silica fume(SF), blast furnace slag(BS) and blast furnace slag along with fly ash(BS+FA). An increase in SRA resulted in retarding the setting time of control concrete, while the use of mineral admixture led to a delay of setting time markedly, compared with that of control concrete under no SRA content. Meanwhile, An increase in SRA in concrete with mineral admixture exhibited comparable setting delay with control concrete. Furthermore, in case of the use of BS and SF, acceleration of setting time was observed with increase of SRA content. It is considered that proper dosage of SRA of concrete with SF and BS to secure similar setting delay with control concrete require rather larger than that of control concrete. Accordingly, For concrete with mineral admixture, in order to decide the proper dosage of SRA, application of correction factors is needed.

• Journal of Environmental Science International
• /
• v.18 no.10
• /
• pp.1181-1187
• /
• 2009

Results for application of RDF(Refuse Derived Fuel) to selected wastes in metropolitan and small and medium cities are as follows. The physical characteristics of waste are paper, plastic, food waste, and so on. The proximate analysis in P city showed 20.2% of moisture, 71% of combustible material, and 8.8% of ash on annual average. That in G city showed 31.6% of moisture, 59.5% of combustible material, and 8.9% of ash. Ultimate analysis in P city showed 52.04% of carbon, 7.02% of hydrogen, 28.80% of oxygen, 0.66% of nitrogen, and 0.09% of sulfur. Heating value was 3,363 kcal/kg. Ultimate analysis in G city showed 50.85% of carbon, 6.56% of hydrogen, 29.86% of oxygen, 0.79% of nitrogen, and 0.12% of sulfur. Heating value in the G city was somewhat lower than that in the P city with 2,632 kcal/kg. Thus, application of RDF in metropolitan city was more effective than that in small and medium cities. Heating value in mixture for the P city was lower than that in waste of the volume rate waste charge system alone by 143 kcal/kg. In proximate analysis, moisture, and combustible material were likely to be more adequate to RDF.

• Advances in materials Research
• /
• v.9 no.3
• /
• pp.203-218
• /
• 2020

This research paper presents the outcomes in terms of mechanical and microstructural characteristics of binary and ternary concrete when exposed to elevated temperature. Three parameter were taken into account, (a) elevated temperature (i.e., 200, 400, 600 and 800℃) (b) binary concrete with cementitious material sugarcane bagasse ash (SCBA) and ground granulated blast furnace slag (GGBFS) replacement percentage (i.e., 0, 15, 20, 25 and 30%) and (c) ternary concrete with cementitious material SCBA and GGBFS replacement percentage (i.e., 0, 15, 20, 25 and 30%). A total of 285 standard cube specimens (150 mm × 150 mm × 150 mm) containing Ordinary Portland Cement (OPC), SCBA, and GGBFS were made. These specimens then exposed to several elevated temperatures for 2 h, afterword is allowed to cool at room temperature. The following basic physical, mechanical, and microstructural characteristics were then determined and discussed. (a) mass loss ratio, (b) ultrasonic pulse velocity (UPV) (c) physical behavior, (d) compressive strength, and (e) field emission scanning electron microscope (FESEM). It was found that compressive strength increases up to 400℃; beyond this temperature, it decreases. UPV value and massloss decrease with increase in temperature as well as the change in color and crack were observed at a higher temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.5
• /
• pp.358-364
• /
• 2009

This paper is to investigate the influence of driving patterns of slow and high speed vehicles on the performance of continuously regenerating diesel particulate filter(DPF) system matched with operating conditions in field application. The DPF performance test for field application was carried out for two identical DPFs installed to slow and high speed vehicles. A slow speed vehicle was selected among local buses which have driving patterns to repeat running and stop frequently, while a high speed vehicle was prepared to have long route of high speed over 60km/h like inter-city buses. In this test, the regeneration performance on the DPF of slow speed vehicle deteriorated because of high soot load index(SLI) in spite of same balance point temperature(BPT) distribution for high speed vehicle. The DPF of slow speed vehicle melted in the end because the rapid increase of back pressure caused high temperature over $1200^{\circ}C$ in the ceramic wall of DPF. The PM components like ash collected to the filter in the DPF were analyzed in order to investigate the cause of the defect and provide an operation performance of DPF system. In the result of the analysis, high levels of lubrication oil ash(Ca, Mg, P, Zn) were detected.

• 한국해양학회지
• /
• v.10 no.1
• /
• pp.17-24
• /
• 1975

In order to clarify the accumulation of radioactive materials in marine organisms of Korea, the present investigation is carried out with 54 samples of edible seaweeds collected from eight sampling sites along the coast of Korea during September, 1973 and April, 1974. In this paper, ash contents, gross alpha activities and gross beta activities are detected. The ash content is 7.53- 15.95% in the species investigated. Among the algal phyla it is about 13.13% in green algae, 12.77% in brown algae, and 10.77% in red algae on an average. On the other hand, gross alpha activities fluctuate from 180.0 pCi/Kg to 1082.6 pCi /Kg-fresh material experimented, and are 530.72 pCi/Kg on an average. They increase from green to red and brown algae, in turn. The activities in a single species collected at the same season increse from eastern to western and southern coasts of Korea, in turn. Gross beta activities, however, fluctuate from 2.40 nCi/Kg to 22.14 nCi/Kg-fresh material experimented, and 9.03 nCi/Kg on an average. They increase also from green to red nd brown algae, in turn. The gross beta activities are specially higher in Sargassum thunbergii, 22.14 nCi/Kg It is expected that this plant could be an indicator to detect the activities in the marine algae along the coast of Korea.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.4
• /
• pp.429-436
• /
• 2004

Circulating fluidized bed combustion (hereafter CFBC) technology enables an efficient combustion for the materials with low heating values such as high ash coal and sludges. It also has desulfation function by adding limestone directly to combustor. The CFBC has been considered as one of the best processes for low grade coal containing with large contents of ash and sulfur. In this paper, in order to various tests were performed to find the optimum desulfation condition for CFBC using Korean Anthracite. We surveyed possible parameters and conducted desulfation efficiency test in D Thermal Power Plant. In addition, the result of some fundamental theoretical consideration was discussed with CFBC. Optimum limestone size could be considered to be 0.1-0.3mm irrespective of combustion temperature and Ca/S molar ratio variation. Desulfation efficiency increased as the molar ratio increased. Because desulfation process occurs at the surface at higher temperature, inner side of limestone can＇t be utilized. When surface area is not appropriate, some SO$_2$ emit without reaction. Optimum molar ratio should be decided after considering chemical and physical properties of limestone and coal thoroughly such as particle size, pore size and HGI. Commercial CFBC is operated at Ca/S 1.6. Combustor temperature 840-87$0^{\circ}C$ shows good desulfation efficiency.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.12 no.4
• /
• pp.59-66
• /
• 2012

This study is interested in identifying the effectiveness of alkali-activated fire protection material compounds including the alkali-activator such as potassium hydroxide, sodium silicate and fly ash as the fire resistant finishing materials. Also, this paper is concerned with change in compressive strength and pore structure of the alkali-activated fire protection material at high temperatures. The testing methods of fire protection materials in high temperature properties are make use of TG-DSC and mercury intrusion porosimetry measurements. This study results show that compressive strength is rapidly degraded depending on a rise of heating temperature. Porosity showed a tendency to increase irrespective of specimen types. This is due to both the outbreak of collapse of gel comprising the cement and a micro crack by heating. However, alkali-activated fire protection material composed of potassium hydroxide, sodium silicate and fly ash has the thermal stability of the slight decrease of compressive strength and porosity at high temperature. These thermal stability is caused by the ceramic binding capacity induced by alkali activation reaction by the reason of the thermal analysis result not showing the decomposition of calcium hydrate.

• Computers and Concrete
• /
• v.15 no.2
• /
• pp.215-229
• /
• 2015

The emerging technology of self compacting concrete, fiber reinforcement together reduces vibration and substitute conventional reinforcement which help in improving the economic efficiency of the construction. The objective of this work is to find the regression model to determine the response surface of mix proportioning Steel Fiber Reinforced Self Compacting Concrete (SFSCC) using statistical investigation. A total of 30 mixtures were designed and analyzed based on Design of Experiment (DOE). The fresh properties of SCC and mechanical properties of concrete were studied using Response Surface Methodology (RSM). The results were analyzed by limited proportion of fly ash, fiber, volume combination ratio of two steel fibers with aspect ratio of 50/35: 60/30 and super plasticizer (SP) dosage. The center composite designs (CCD) have selected to produce the response in quadratic equation. The model responses included in the primary stage were flowing ability, filling ability, passing ability and segregation index whereas in harden stage of concrete, compressive strength, split tensile strength and flexural strength at 28 days were tested. In this paper, the regression model and the response surface plots have been discussed, and optimal results were found for all the responses.