• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.112-118
• /
• 2002

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis fur the filling and packing phases. Molding troubles like flow mark, weld line, sink mark, short shot and warpage can be caused by these injection molding process factors. Among them, the short shot was caused by that the packing pressure could not reach properly to the filling end part in the packing phase and hence the flow rate could not be supplied to the full. In addition, as the flow rate for the volumetric shrinkage during the frozen phase could not be supplied properly by the packing pressure, the short shot appeared. Here, the volumetric shrinkage reduced with increasing the packing pressure and also the warpage of molded part increased with increasing the packing pressure.

• 한국공작기계학회논문집
• /
• 제11권4호
• /
• pp.44-53
• /
• 2002

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for the filling and packing phases. Molding troubles like flow mark weld line, sink ma가 short shot and warpage car be caused by these injection molding process factors. Among them the short shot was caused by the fact that the packing pressure could not reach properly to the filling end part in the packing phase and hence the flow rate could not be supplied to the full. In addition as the flow rate for the volumetric shrinkage during the f개zen phase could not be supplied Properly by the packing pressure, the short shot appeared. Here, the volumetric shrinkage reduced with increasing the packing pressure and also the warpage of molded part increased with increasing the packing Pressure.

• 대한기계학회논문집B
• /
• 제25권4호
• /
• pp.554-560
• /
• 2001

Hydrophilic treatment of the packing materials in a cooling tower has been made by the ion assisted reaction (IAR) method to increase the wettability of the packing materials. The effects of hydrophilic treatment of packing materials on the performance of a cooling tower have been investigated in a wide range of operating parameters, such as water flow rate, air flow rate, and the water inlet temperature. A pilot cooling tower has been designed and built to model a counter-flow cooling tower. The results obtained indicate that the packing characteristic value with hydrophilic packing could be substantially increased by 6∼19.3% than that with conventional packing in the operating ranges considered. The correlations of the packing characteristic value as a function of water-to-air ratio are suggested for a counter-flow cooling tower with hydrophilic packing as well as with conventional packing.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1676-1681
• /
• 2004

The main reason for applying positive pressure variable clearance packing in fossil power plant is high efficiency and energy saving movement in the government. This study intends to analyze the turbine efficiency through the shaft packing improvement in thermal power plant and makes its comparison to that of the each packing type

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.715-720
• /
• 2001

The main reason for applying positive pressure variable clearance packing in fossil power plant is high efficiency and energy saving movement in the government. This study intends to analyze the turbine efficiency through the shaft packing improvement in thermal power plant and makes its comparison to that of the used packing.

• 한국환경과학회지
• /
• 제6권4호
• /
• pp.391-397
• /
• 1997

The study was carried out to demonstrate the superiority of used packing in view of energy saving and efficiency of mass transfer, comparing with conventional packing. The results are as follows : 1. Owing to low Pressure drop under high load. 25mm NSW-ring, pp. can cause energy saving 2. The unique magnitudes of used packing are as follows $C_G$=5.78, m=0.67, n=0.46 3. Used packing can make high efficiency including energy saving because of low pres sure drop per the number of transfer unit. To rate the characteristic of packing, It should be carried out that the measurement of pressure drop per packing height and per the number of transfer unfit. This study demonstrated the superiority of used packing by carring out above experiment and could be used as basic reference for design and predicting efficiency of packing tower which is tilled with same packing.

• 한국미생물·생명공학회지
• /
• 제41권2호
• /
• pp.215-220
• /
• 2013

Tobermolite, perlite 및 polyurethane을 충전재로 이용한 바이오필터에 의한 메탄제거 기술이 개발되고 있다. 본 연구에서는 이들 충전재가 메탄산화능에 미치는 영향을 알아보았다. 습지토양과 매립지토양에서 분리한 혼합 메탄산화세균(consortium A, B, C and D)를 접종원으로 하고, 메탄산화속도와 메탄산화세균 수에 미치는 담체(perlite, tobermolite,polyurethane)의 영향을 조사하였다. Perlite를 첨가한 경우 메탄산화속도는 대조군 (담체 미첨가)보다 두 배 이상 증가하였고, 메탄산화세균 수도 10배 이상 증가하였다. Tobermolite를 첨가한 경우에는 일반세균 수 대비 메탄산화세균의 비율이 대조군과 다른 담체에 비해 높았다. 이는 tobermolite가 메탄산화세균이 우점할 수 있는 특이적 담체로 작용함을 시사한다. 이상의 결과로 부터 perlite와 tobermolite는 메탄산화세균의 활성을 증가시키는 서식지를 제공하며 메탄산화 공정시스템에 적용 시 좋은 담체의 역할을 할 수 있을 것으로 기대된다.

• KSBB Journal
• /
• 제16권3호
• /
• pp.314-319
• /
• 2001

A nitrifier consortium immobilized in polyvinyl alcohol was used to remove ammonia nitrogen from synthetic wastewater in an airlift bioreactor. The minimum aeration rates were 0.4, 0.6, 0.8 and 1.0 vvm for 5, 10, 15 and 20% immobilized bead packing volume fraction, respectively. The efficient packing fraction and the aeration rate for ammonia nitrogen removal were 15% and 2.4 vvm, respectively. With a hydraulic retention time of 0.5hr, the removal rate and the efficiency of ammonia nitrogen removal were 1685 g/㎥$.$day and 48% at an influent ammonia nitrogen concentration of 75 g/㎥.

• 한국염색가공학회지
• /
• 제22권3호
• /
• pp.257-263
• /
• 2010

Oil-absorbable nonwovens were produced by meltblown processing of polypropylene chips. In this study, experimental array and variance analysis of the design of experiment were used to increase the field repeatability and universality. Oil absorbency was decreased, as oil absorbable nonwovens of packing density and gearpump speed were increased. Oil absorption rate was increased, as packing density was increased. Also the oil absorption rate increased with increasing gear-pump speed.

• 설비공학논문집
• /
• 제10권3호
• /
• pp.358-367
• /
• 1998

Since the performance of cooling tower is strongly dependent on the thermal performance of the packing, the evaluations of heat transfer rate and fan power from various packing have attracted intense interest. In the present study, two new packings have been devised and their performances have been compared with those of two existing packings to find better shape characteristic. It is found that one of the existing packings, which showed high heat transfer rate and medium fan power due to zig -zag flow passages and highly irregular surfaces, should be adapted.