• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.193-193
• /
• 2011

To obtain ceramic films, the sol-gel coating technique has been broadly used with heat treatment, but crack formation tend to occur during heat treatment in thick sol-gel films. We prepared PZT thin films by sol-gel method with single-step spin coating process. The PZT solution have been synthesized using lead acetate ($Pb(CH_3COO)_2$), zirconium acetylacetonate ($Zr(OC_3H_7^n)_4$), and titanium diisopropoxide bis(acetylacetonate) 75wt% in isopropanol ($Ti(OC_3H_7^i)_2(OC_3H_7^n)_2$) as starting materials and n-propanol was selected as a solvent. The poly(vynilpyrrolidone) (PVP) was added with 0, 0.25, 0.5, 0.75, and 1 molar ratios to control viscosity of solution. We investigated influence of the viscosity on thickness, microstructure, and electrical properties of final PZT films. Thermo-gravimetric analysis and differential scanning calorimeter (TGA/DSC) was carried out from room temperature to $800^{\circ}C$ in order to measure pyrolysis temperature. Structural characteristics were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Ferroelectric and dielectric properties were measured by RT66A (Radiant) and impedance analyzer (Agilent), respectively. The thicknesses of PZT films depended on incorporation of an excess amount of PVP. Finally, we obtained PZT films of good quality without crack formation via single-step spin coating.

• Korean Journal of Materials Research
• /
• v.14 no.5
• /
• pp.334-337
• /
• 2004

Perovskite PMN-PZT-based ceramics were prepared and the$ MnO_2$ doping effects on their piezoelectric properties were investigated. Grain size decreased with increasing the $MnO_2$ content, and the pyrochlore phase was not identified in the sintered PMN-PZT ceramics with 0.01～1.0wt% $MnO_2$. Piezoelectric voltage and charge constants were reduced and mechanical quality factor increased with increasing the $MnO_2$ content. However, electromechanical coupling coefficient slightly decreased with increasing the MnO$_2$ content without regard to the grain size.

• Structural Engineering and Mechanics
• /
• v.54 no.5
• /
• pp.955-971
• /
• 2015

In this paper, the influence of the polled direction of piezoelectric materials on the stress distribution is studied under time-harmonic dynamical load (time-harmonic Lamb's problem). The system considered in this study consists of piezoelectric covering layer and piezoelectric half-plane, and the harmonic dynamical load acts on the free face of the covering layer. The investigations are carried out by utilizing the exact equations of motion and relations of the linear theory of electro-elasticity. The plane-strain state is considered. It is assumed that the perfect contact conditions between the covering layer and half-plane are satisfied. The boundary value problems under consideration are solved by employing Fourier exponential transformation techniques with respect to coordinates directed along the interface line. Numerical results on the influence of the polled direction of the piezoelectric materials such as PZT-5A, PZT-5H, PZT-4 and PZT-7A on the normal stresses, shear stresses and electric potential acting on the interface plane are presented and discussed. As a result of the analyses, it is established that the polled directions of the piezoelectric materials play an important role on the values of the studied stresses and electric potential.

• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.516-520
• /
• 2005

Conditions for formation of perovskite Pb(Zr$_{0.52}$Ti$_{0.48}$)O$_{3}$ phase by the hydrothermal synthesis are investigated. Pb(Zr$_{0.52}$ Ti$_{0.48}$)O$_{3}$ ceramics were synthesized by hydrothermal process above 180$^{\circ}C$ for 2 h reaction using 5$\~$30 M KOH solution as a mineralizer. Particle size increases in proportion to the mineralizer concentration. As a result of EOX analysis, PZT powders synthesized using 50 M of KOH as a mineralizer were considered as 2.42 mol$\%$ K doped-PZT powders. And 2.42 mol$\%$ K doped-PZT has much higher mechanical quality factor than undoped PZT ceramics. The sintering properties showed 7.987 g/cm$^{3}$ of sintered density and 3$\~$4 $\mu$m of grain size.

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.271-275
• /
• 2011

This paper proposes a magnetoelectric (ME) composite transducer structure consisting of a magnetostrictive H-type Fe-Ni fork substrate and piezoelectric PZT plates. The fork composite structure has a higher ME voltage coefficient compared to other ME composite structures due to the higher quality (Q) factor. The ME sensitivity of the fork structure reaches 12 V/Oe (i.e., 150 V/cm Oe). The fork composite with two PZT plates electrically connected in series exhibits over 5 times higher ME voltage coefficient than the output of the rectangle structure in the same size. The experiment shows the composite of a Fe-Ni fork substrate and PZT plates has a significantly enhanced ME voltage coefficient and a higher ME sensitivity relative to the prior sandwiched composite laminates. By the use of a lock-in amplifier with 10 nV resolution, this transducer can detect a weak magnetic field of less than $10^{-12}$ T. This transducer can also be designed for a magnetoelectric energy harvester due to its passive high-efficiency ME energy conversion.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.9
• /
• pp.541-545
• /
• 2017

$Pb(Zr_{0.52}Ti_{0.48})O_3$ (PZT) films with a thickness of $5{\sim}10{\mu}m$ at the morphotropic phase boundary were fabricated by aerosol-deposition (AD), and their phase evolution and electrical properties were investigated. The microstructure of the AD PZT films revealed nanosized grains with a low crystallinity and a dense structure at room temperature. The AD PZT films showed a mixture of tetragonal and rhombohedral phases. The post-annealing temperature was varied to study the phase transition behavior. The crystallinity of the AD PZT films was enhanced by annealing at 450, 550, and $650^{\circ}C$ for 2 h. At $650^{\circ}C$, the tetragonal and rhombohedral phases reacted to form a bridge phase between the two phases. The polarization-electric field hysteresis loops of the AD PZT film annealed at $650^{\circ}C$ exhibited a smaller cohesive field and a lower slim hysteresis than the films annealed at 450 and $550^{\circ}C$.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.1
• /
• pp.33-37
• /
• 2000

The 1-3 piezoelectric composite transducer with 75 volume percents PZT was fabricated by the dicing-filling method. The resonance modes of the 1-3 transducer have been studied with electric impedance measurement as a function of frequency. The fundamental frequencies of the planar and thickness mode were observed at 0.95MHz and 1.63MHz respectively, but the lateral mode was not observed. In the thickness mode, the electromechanical coupling coefficient of the 1-3 piezoelectric composite transducer, 0.54, was very closed to that of the single phase PZT(0.52). The pulse-echo response by exciting the 1-3 transducer with an electric pulse was observed from the water/reflector interface, and analyzed bandwidth by the spectrum of the impulse response. The quality factor Q for the 1-3 transducer was observed as 1.5 smaller than that of the single phase(80) and then the 1-3 transducer may be used to the broad band type transducer applications.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.3 no.2
• /
• pp.1-6
• /
• 2006

The pressure regulator which is used for controlling the reducing pressure in the piezoelectrically driven pneumatic valve has been studied. The pneumatic valve of this study object is 2-stage type and consists of a piezoelectric actuator, a controller, a poppet valve and a pressure regulator. Nominal flow of 50 lpm, maximum operating pressure of 0.9MPa and frequency characteristic of 10Hz and over are required in this pneumatic valve, but the pressure regulator is needed because piezoelectric actuator has no ability to control the pressure of 0.9MPa directly. In this study, bimorph type PZT actuator of $25.2mm(L){\times}7.2mm(W){\times}0.5mm(H)$ with constant of $-220{\times}10-12$ CN-1 was proposed and investigated. Maximum operating force of 0.052 N and maximum displacement of $63{\mu}m$ were gotten from the fabricated PZT actuator. From the analysis results, the orifice diameter of 0.6mm for a piezoelectric actuator was derived and then the pressure regulator which can be operated under 0.15 MPa easily was designed and manufactured. Performance and effects of design parameters were simulated by the Simulink of Matlab software, and it was confirmed that the performance characteristics of manufactured pressure regulator are superior in the common use pressure range of 0.5 MPa to 0.7 MPa. The results show that the proposed pressure regulator is suitable for the pneumatic valve with a PZT actuator.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.38-40
• /
• 2005

Microdrive with high precision and light mass enough to install on mouse head was fabricated for recording the reliable signal of neuron cell to understand the brain study. The proposed microdrive has three H-form PZT actuators and its guide structure. The microdrive operation principle is based on the well known inchworm principle. The synchronization of three PZT actuators is able to produce the linear motion along the guide structure. Our proposed microdrive has a precise accuracy of about 100nm and a long stroke of about 5mm. The electrode which is used for the recording of the action potential of the neuron cell was fixed at one of PZT actuators. The proposed microdrive was suited to acquisition of signals from in vivo extra-cellular single-unit recoding. On the condition of the anesthetized mouse, the single-unit signals could be recorded by using the proposed microdrive. In addition, applying the PZT microdrive to an alert mouse, we try to implant it on a mouse brain skull to explore single neuron firing.

• Particle and aerosol research
• /
• v.4 no.1
• /
• pp.21-25
• /
• 2008

$Pb(Zr_{0.53}Ti_{0.47})O_3$ (PZT) was synthesized by a multiple wet dry process. Precipitates prepared from reaction between $ZrOCl_2{\cdot}8H_2O$ and $TiOCl_2$ and $NH_4OH$ in an aqueous solution was dried at $100^{\circ}C$, and calcined at $500^{\circ}C$ and $700^{\circ}C$. The mixture mixed with PbO and as-dried or calcined $Zr_{0.53}Ti_{0.47}O_4$ (ZT) powders was calcined again at 700 and $800^{\circ}C$. Well crystallized ZT and PZT were formed at even $700^{\circ}C$. PZT piezoelectric ceramics of more than 98.5% in a relative density was obtained by sintering at as low as $900^{\circ}C$.