• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 정기총회 및 창립40주년기념 학술대회 학회본부
• /
• pp.254-256
• /
• 1987

In this study, piezoelectric composite materials of O-3 connectivity were made by, mixing FZT ceramics with polymers, the dependence of volume % PZT and poling condition for dielectric and piezoelectric properties were investigated. The measured value of dielectric constant was dependent on the volume % PZT, which was exponentially increased with volume %PZT. Piezoelectric coefficient ($\bar{d}_{33}$) was exponentially increased with volume % PZT. Voltage coefficient ($\bar{g}_{33}$) was decreased with volume % PZT, but it was larger than that of single phase PZT ($\bar{g}_{33}$) because the dielectric constant ($\bar{\varepsilon}_{33}$) of composite materials was decreased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.40-43
• /
• 1996

Substrates of SAW filter are mainly single crystal such as LiNbO$_3$, LiTaO$_3$. However, fabrication of crystal is difficult and cost is very high. In this study, crystal was substituted for piezoelectric ceramics which has simple fabrication process. The same SAW filter mask was photolithographed on crystal(LiNbO$_3$) substrate and ceramic(PZT4, PZT5A and PZT8) substrate in order to compare experimental value with theoretical value. The difference of center frequency was only 3.7%. PZT8 showed good bandwidth properties. It is considered that PZT8 has higher mechanical quality factor and propagation velocity than PZT4, PTT5A.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.650-652
• /
• 2002

In this paper, specimens was manufactured in general method annexing PAN-PZT+0.8wt%Mn+1wt% Nb ceramics doped by Sr(0.0 ~ 1.2 wt%). and the following conclusion has been deduced. In XRD, the crystal structure of ceramic has the rombohedral structure and consequently the specimen characterized by MPB was manufactured. According to dopping with Sr, electromechanical factor(kp) little is changed. kp was maximum value 31.31[%] at Sr 1.2[wt%]. mechanical quality factor(Qm) was maximum value 371.879 at Sr 0.6[wt%].

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.217-218
• /
• 2006

In this study, In order to develop the low temperature sintering multilayer piezoelectric actuator, PMN-PNN-PZT system ceramics were manufactured with the sintering temperature, and their microstructure and piezoelectric properties were investigated. At the composition ceramics sintered at $900^{\circ}C$, dielectric constant(${\varepsilone}_r$), electromechanical coupling factor($k_p$), piezoelectric constant($d_{33}$) and mechanical quality factor(Qm) showed the optimal value of 1095, 0.60, 363 and 1055, respectively, for multilayer piezoelectric actuator application.

• 한국전기전자재료학회논문지
• /
• 제19권12호
• /
• pp.1118-1122
• /
• 2006

In this study, in order to develop the low temperature sintering multilayer piezoelectric actuator, PMN-PNN-PZT system ceramics were manufactured and their microstructure, ferroelectric and piezoelectric properties were investigated. By increasing sintering temperature, remanent polarization$(P_r)$ was increased due to the increase of sinterability and grain size. However, coercive $field(E_c)$ showed an opposite tendency to remanent polarization owing to the feasibility of domain wall motion. At the sintering temperature of $900^{\circ}C$, dielectric $constant({\varepsilon}_r)$, electromechanical coupling $factor(k_p)$, piezoelectric $constant(d_{33})$ and mechanical quality $factor(Q_m)$ showed the optimal value of 1095, 0.60, 363 and 1055, respectively, for multilayer piezoelectric actuator application.

• 한국세라믹학회지
• /
• 제30권9호
• /
• pp.761-767
• /
• 1993

Electrical and mechanical properties of Pb(Mg, Te, Mn, Nb)O3-PZT ceramics are investigated as a function of CeO2 addition (0 to 0.3wt%), and the output characteristics of piezoelectric transformer are also presented. The grain size decreased and the shapes of particles were more uniform with the addition of CeO2. The coercive electric field(9500V/cm), mechanical quality factor (2500) and bend strength (1065kg/$\textrm{cm}^2$) were improved by addition of CeO2 0.2wt%. After repetition of a number of stress cycles, the degradation of k33 was not found in this sample. The voltage step-up ratio (Vdc/Vrms) of piezoelectric ceramic transformer (half wavevoltage doubler, load resistor 100M.ohm) was about 950 in a linear region, its value was relatively higher than other materials.

• 한국세라믹학회지
• /
• 제42권10호
• /
• pp.685-690
• /
• 2005

Pb(Zr,Ti)$O_{3}$Pb($Mn_{1/3}$$Nb_{2/3}$)$O_{3}$ powder was successfully synthesised by high-energy milling method, and the behavior of low­temperature sintering and piezoelectrical properties of Pb(Zr,Ti)$O_{3}$-Pb($Mn_{1/3}$$Nb_{2/3}$)$O_{3}$ ceramics were investigated as a function of mechanical alloying time. In order to confirm whether the Perovskite phase in this composition was formed by mechanical activation technique or not, we performed X-Ray Diffraction pattern analysis (XRD). The microstructure for the sintered samples were characterized using a Scanning Electronic Microscope (SEM). And the piezoelectrical properties ($k_{p}$ and $Q_{m}$) of the sintered samples was measured using HP 4194A impedance analyzer.

• The Korean Journal of Ceramics
• /
• 제1권4호
• /
• pp.197-203
• /
• 1995

Nearly fully dense PZT samples both with tetragonal and with morphotropic phase boundary compositions were prepared by the conventional powder processing and sintering. A micro-indentation technique was used to evaluate the dependence of fracture toughness on remanent polarization, crack length and the direction of crack propagation. The result shows that the toughness increases with the remanent polarization along the poling direction and decreases in the transverse direction. The dependence of toughness on the remanent polarization is neither symmetric nor linear but rather shown to be saturated quickly with the increase in remanent polariztion. R-curve behaviors are observed in both poled and unpoled samples. Sequential SEM and XRD studies on annealed, poled, ground, fractured and etched samples show that domain switching is evident as a viable toughening mechanism but might depend upon the rate of crack propagation. Grain bridging is also observed as one of the active toughening mechanisms.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.645-648
• /
• 1999

With the variation of the sintering temperature and the amounts of B$_2$O$_3$, Bi$_3$O$_3$ and V$_2$O$_{5}$ , the densification and the piezoelectric properties of the MnO$_2$-doped PMN-PZT were investigated. The additives decreased the sintering temperature of ceramics. In the case of 0.5wt% B$_2$O$_3$, the sintering density, the mechanical quality factor, the electromechanical coupling factor and the piezoelectric constant were 7.51 (g/㎤), 1397, 51.1% and 305 (X10$^{-12}$ C/N) respectivly at 105$0^{\circ}C$. And the addition of lwt% Bi$_2$O$_3$, they were 7.59 (g/㎤) ,833,49.8% and 308 (X10$^{-12}$ C/N) respectivly at 1000 $^{\circ}C$.

• 한국전기전자재료학회논문지
• /
• 제20권12호
• /
• pp.1034-1038
• /
• 2007

In order to develop the composition ceramics capable of being sintered at low temperature with high piezoelectric properties for multilayer piezoelectric actuator application, PZW-PMN-PZT system ceramics were manufactured according to sintering aid $Li_2CO_3$ addition and their microstructural, dielectric and piezoelectric properties were investigated. The crystal structure of the specimens showed a perovskite phase and no pyrochlore or other second phase was detected. At the sintering temperature of $900\;^{\circ}C,\;0.2\;wt%Li_2CO_3$ added specimen showed a optimum values of kp = 0.562, $d_{33}\;=\;360\;pC/N$ and Qm = 1184, respectively.