• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.2
• /
• pp.164-174
• /
• 1990

The improvement of linearized characteistics of induction motor control system with field oriented method is presented in this paper. A fully digitally controlled induction motor driver system based on the proposed linear control condition is described. The control system consists of IBM-PC/AT microcomputer, VSI PWM Inverter, and PI controller with softwave. By controlling the torque component, the rated flux component can be kept constant, even in the transient state. It is clearly confirmed by experiment that the improvement of the vector control condition is satisfactory. A simplified control model of an induction motor similar to the model for a separately excited DC motor drive system is obtained.

• Journal of Korean Vacuum Science & Technology
• /
• v.3 no.1
• /
• pp.85-89
• /
• 1999

FDE panel was successfully fabricated through the integration of a 0.7" diagonal Si-based Mo-tip FEA with 25${\times}$25 pixels, Y2O3:Eu or ZnO:Zn phosphor screen, and vacuum sealing through an exhausting glass tube, including a getter. The panel system was driven by an external driver circuit having pulse width modulation(PWM) driving scheme. Before character imaging, it was stabilized through tip aging by slowly increasing a pulse-mode emission current and phosphor aging by a coulombic charging process. After aging, luminescent characteristics such as emission uniformity, charging and arcing phenomena were shown to be improved significantly.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.93-95
• /
• 2001

This paper describes detent force minimization techniques of Permanment Magnet Linear Synchronous Motor(PMLSM) for the improvement of control and the driver system to control the position and velocity, PMLSM are simulated by operating open-loop system and PI control system, and in actuality the control system is implemented by DSP based controller and PWM inverter to investigate the characteristics of both open-loop system and PI control system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05c
• /
• pp.53-56
• /
• 2004

This paper describes the method of position error reduction in Linear Pulse Motor (LPM). Though the micro step exiting method is applied, the vibration and position error caused by trust distortion from mechanism still remains. This paper presents the method for reduction of position error on moving the mover at whole cycle, by compensating a scale factor through real-time control of the PWM pulse width corresponding to exiting current command and absolute position error from linear encoder.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.1025-1028
• /
• 1993

In this paper, an intelligent control scheme with multi-stage fuzzy inference is developed for a myoelectric prosthesis to achieve natural control with tactile feedback based on fuzzy control strategies. Strain gauges and a potentiometer are added to the prosthesis for tactile feedback with a PWM motor driver developed to save the battery power. According to the multi-stage fuzzy inference, the prosthesis can determine the stiffness of the object and hold an object without injuring it, meanwhile, the hysteresis phenomenon is an 80196KC single-chip microcontroller to replace the original controller.

• Journal of Power Electronics
• /
• v.12 no.5
• /
• pp.715-722
• /
• 2012

New discrete time domain models for the peak current controlled (PCC) power LED drivers in continuous conduction mode include for the first time the effects of the time delay in the pulse-width-modulator. Realistic amounts of time delay are found to have significant effects on the average output LED current and on the critical inductor value at the boundary between the two conduction modes. Especially, the time delay can provide an accurate LED current for the PCC buck converter with a wide input voltage. The models can also predict the critical inductor value at the mode boundary as functions of the input voltage and the time delay. The overshoot of the peak inductor current due to the time delay results in the increase of the average output current and the reduction of the critical inductor value at the mode boundary in all converters. Experimental results are presented for the PCC buck LED driver with constant-frequency controller.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.407-408
• /
• 2017

In regenerative mode of an IPMSM control system without a bi-directional DC-DC converter, the 3-phase PWM inverter charges the battery. At this time, the regenerative torque reference for braking must output the proper torque reference to charge the battery. This paper proposed a regeneration control method that controls the voltage and current of the battery through CC-CV control at the regenerative braking torque corresponding to the driver's brake control.

• Journal of Digital Contents Society
• /
• v.19 no.8
• /
• pp.1603-1615
• /
• 2018

In order to achieve the low complexity and area, power in the design of Optical Image Stabilization (OIS) suitable for the smart phone, this paper presents the following design explorations, such as; optimization of gyroscope sampling rate, simple and accurate gyroscope filters, and reduced operating frequency of motion compensation, optimized bit width in ADC and DAC, evaluation of noise effects due to PWM driving. In experiments of gyroscope sampling frequencies, it is found that error values are unvaried in the frequency above 5KHz. The gyroscope filter is efficiently designed by combining the Fuzzy algorithm, to illustrate the reasonable compensation for the angle and phase errors. Further, in the PWM design, the power consumption of 2MHz driving is shown to decrease up to 50% with respect to the linear driving, and the imaging noises are reduced in the driving frequency above 2MHz driving frequency. The operating frequency could be reduced to 5KHz in controller and 10KHz in driver, respectively, in the motion compensation. For ADC and DAC, the optimized exploration experiments verify the minimum bit width of 11bits in ADC as well as 10bits in DAC without the performance degradation.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1540-1551
• /
• 2015

The detection of position and speed in BLDC motors without using position sensors has meant many efforts for the last decades. The aim of this paper is to develop a sensorless technique for detecting the position and speed of BLDC motors, and to overcome the drawbacks of position sensor-based methods by improving the performance of traditional approaches oriented to motor phase voltage sensing. The position and speed information is obtained by computing the derivative of the terminal phase voltages regarding to a virtual neutral point. For starting-up the motor and implementing the algorithms of the detection technique, a FPGA board with a real-time processor is used. Also, a versatile hardware has been developed for driving BLDC motors through pulse width modulation (PWM) signals. Delta and wye winding motors have been considered for evaluating the performance of the designed hardware and software, and tests with and without load are performed. Experimental results for validating the detection technique were attained in the range 5-1500 rpm and 5-150 rpm under no-load and full-load conditions, respectively. Specifically, speed and position square errors lower than 3 rpm and between 10º-30º were obtained without load. In addition, the speed and position errors after full-load tests were around 1 rpm and between 10º-15º, respectively. These results provide the evidence that the developed technique allows to detect the position and speed of BLDC motors with low accuracy errors at starting-up and over a wide speed range, and reduce the influence of noise in position sensing, which suggest that it can be satisfactorily used as a reliable alternative to position sensors in precision applications.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.478-487
• /
• 2003

In this paper, a type and special feature of Multi-level inverter used in medium-voltage and high-capacity motor driver is introduced. Especially, a power quality and structural advantages of H-Bridge Multi-level inverter is described. It presented the specific structure of power circuit, design method, controller composition and PWM techniques of the cascaded H-Bridge Multi-level inverter which is developed. The feasibility of the developed product based on 3,300V lMVA 7-level H-bridge inverter was studied by experiments and we get conclusion that 1)generate of near-sinusoidal output voltage; 2)is low dv/dt at output voltage; 3)reduce the harmonic injection at input; Experiment demonstrate that it is very economical in productivity because of using the existing production technique and examination equipment, and has the reliability and a good maintenance due to the structure of Power Cell unit combination as well as low cost IGBT.