• Proceedings of the Korean Vacuum Society Conference
• /
• 2003.02a
• /
• pp.70-70
• /
• 2003

• The Journal of the Acoustical Society of Korea
• /
• v.30 no.4
• /
• pp.215-222
• /
• 2011

In order to obtain high resolution images, a focusing ultrasonic transducer operated in very high frequency (VHF) range was fabricated and its characteristics were evaluated. A 9-${\mu}m$ thick PVDF film with only one metalized surface for electric ground was adhered to a CCP (Copper-clad polyimide) film by using epoxy. It was pressed by a metal ball to form a concave surface and its rear side was filled with the epoxy. The radius of curvature and the f-number of the fabricated transducer are 7.5 mm and 1.7, respectively. The pulse-echo measurement results from a target located at the focal point showed that the frequency bandwidth was 35.0 MHz and the insertion loss near the peak frequency of approximately 40 MHz was about 60 dB. Those values agreed well with the simulation results by the KLM equivalent circuit analysis including the effect of the epoxy bonding layer. When the image of thin copper lines by the 35 MHz transducer of the UBM (Ultrasonic Backscattering Microscope) system was compared with the image by the transducer fabricated in this study, the fabricated transducer was observed that the axial resolution was improved although the lateral resolution was degraded.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.347-350
• /
• 2000

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li polymer battery. The temperature dependence of conductivity, impedance spectroscopy and electrochemical properties of PMMA/PVDF electrolytes as a function of a mixed ratio were reported for PMMA/PVDF based polymer electrolyte films, which were prepared by thermal gellification method of preweighed PMMA/PVDF, plasticizer and Li salt. The ion conductivity of PMMA/PVDF electrolytes was 10$\^$-3/S/cm, which may be applicable to a constituent of lithium secondary battery. 5PMMA20PVDFLiC1O$_4$PC$\sub$8/EC$\sub$8/ electrolyte remains stable up to 5V vs. Li/Li$\^$+/. Steady state current method and AC impedance were used for the determination of transference numbers in PMMA/PVDF electrolyte film. The transference number of 5PMMA20PVDFLiC1O$_4$PC$\sub$8/EC$\sub$8/ electrolyte is 0.55.

• Macromolecular Research
• /
• v.16 no.3
• /
• pp.247-252
• /
• 2008

Lithium gel electrolytes based on a mixed polymer matrix consisting of poly(vinylidenefluoride-hexafluoropropylene) (PVDF-HFP) and cyanoresin type M (CRM) were prepared using an in situ blending process. The CRM used in this study was a copolymer of cyanoethyl pullulan and cyanoethyl poly(vinyl alcohol) (PVA) with a mole ratio of 1:1. The mixed plasticizer was ethylene carbonate (EC) and propylene carbonate (PC) with a volume ratio of 1:1. In this study, the presence of PVDF in the electrolytes helps to form a dimensionally stable film over a broad composition range, and decreases the viscosity. In addition, it provides better rheological properties that are suitable for the extrusion of thin films. However, the presence of HFP has a positive effect on generating an amorphous domain in a crystalline PVDF structure. The ionic conductivity of the polymer electrolytes was investigated in the range 298-333 K. The introduction of CRM into the PVDF-HFP/$LiPF_6$, complex produced a PVDF-HFP/CRM/$LiPF_6$ complex with a higher ionic conductivity and improved thermal stability and dynamic mechanical properties than a simple PVDF-HFP/$LiPF_6$, complex.

• The Journal of the Acoustical Society of Korea
• /
• v.33 no.2
• /
• pp.102-110
• /
• 2014

The effect of a bonding layer on the performance of a quarter-wave (${\lambda}/4$) mode PVDF ultrasound transducer having not only a piezoelectric layer but also a non-piezoelectric layer between two electrodes was analyzed. The equivalent circuit of a transmission line model by Kikuchi et al.[Sound of IEICE, 55-A, 331-338 (1981)] was introduced for the analysis. The validity of the model was confirmed by comparison with a KLM model for three postulated adhesion cases of a $80{\mu}m$ thick piezoelectric PVDF film to a copper (Cu) backer. The pulse-echo responses of five PVDF transducers, each fabricated with a different thickness ($5{\mu}m{\sim}20{\mu}m$) of the bonding layer, were measured and the results were compared with those by simulation. The two results were in good agreement with each other and it was noted that the effect of the bonding layer on the performance of the transducer could be analyzed by the Kikuchi model. In detail, the $20{\mu}m$ bonding layer decreased the center frequency and the bandwidth by about 19.7 % and 25.0 %, respectively, and increased the insertion loss by 57.2 %.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.451-453
• /
• 2010

PVDF(polyvinylidene fluoride) 필름은 압전특성을 가지며 음파에너지를 발생시키는 유연성 고분자필름이다. 이 연구에서는 기존 원통형 연직 배수재에 PVDF 필름의 음파에너지를 적용하여 점토의 미세입자가 배수재의 성능을 저하시키는 막힘현상(clogging)을 방지함으로써 배수재의 성능을 향상시키고, 압밀을 촉진시키고자 하였다.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.125-128
• /
• 2003

Low-velocity impact damage is a major concern in the design of structures made of composite materials, because impact damage is hidden inside and cannot be detected by visual inspection. The piezoelectric thin film sensor can be used to detect variations in structural and material properties for structural health monitoring. In this paper, the PVDF and PZT sensors were used for monitoring impact damage initiation in Gr/Ep composite panel to illustrate this potential benefit. A series of impact test at various impact energy by changing impact mass and height is performed on the instrumented drop weight impact tester. The wavelet transform(WT) is used to decompose the piezoelectric sensor signals in this study. Test results show that the particular waveform of sensor signals implying the damage initiation and development are detected above the damage initiation impact energy. And it is found that both PZT and PVDF sensors can be used to detect the impact damage.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.12 no.2
• /
• pp.7-13
• /
• 1992

In this study, we examine the characteristics of beam and the effect of these characteristics on the flaw detection by using different type of two transducers, which are PZT and PVDF film transducer. Consequently, the detection of infinitesimal flaw is more possible than PZT, since it has beam width at focus of $60%{\sim}65%$ in contrast with PZT's. Moreover we can know PVDF transducer has superiority in detecting ability for sub-surface flaw detection in view of its acoustic impedance is near to water's and its focusing range is narrower than PZT's as $65{\sim}85%$ because it has spherical surface.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.74-77
• /
• 2001

We have fabricated a high-Tc superconductive transistor with polyvinylidene fluoride (PVDF) gate electrode on MgO bicrystal Josephson junction by spin-coating method. The PVDF ferroelectric film is found to be suitable fur a gate electrode of the superconductive transistor since it has not only small leakage current but also high dieletric constant at low temperature. For the application of superconducting-FET, we investigated millimeter wave properties (60 GHz band) of the Josephson junction with PVDF gate electrode.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.61.4-61
• /
• 2001

This research is the development of a distributed flexible tactile sensor for service robots using PVDF (polyvinylidene fluoride) film for the detection of the contact state in real time. The tactile sensor which has 8$\times$8 taxels is fabricated using PVDF film and flexible circuitry. The proposed fabrication method is simple and easy to make the sensor in the laboratory without using any special equipment. Experimental results on static and dynamic properties are obtained. In order to investigate the properties of the sensor, the sensor output to the arbitrary forces and frequencies are measured using the shaker with the force sensor.