• Journal of the Korean Chemical Society
• /
• v.44 no.6
• /
• pp.592-599
• /
• 2000

The fine particles of binary ceramic composite of titania-partially-stabilized zirconia(TPSZ) were synthesized by ultrasonic spray pyrolysis at the various temperatures, compositions and concentrations and the effects of process factors for synthesis on the characteristics of fine particles were discussed. The starting salt solutions were prepared to have the ionic concentrations of 0.025~0.1 M aqueous solutions. The fine particles were prepared to have the compositions of 90~97.5 wt% of $ZrO_2$ and 2.5~10 wt% of $TiO_2$. The temperatures for particle synthesis were regulated to be 400~550$^{\circ}C$ as a drying zone, 800~1100$^{\circ}C$ as a pyrolysis zone. The produced fine particles were collected by a wet process and analyzed to investigate characteristic properties after being dried. The compositions of ceramic fine particles were determined by Inductively Coupled Plasma-Atomic Emission Spectroscopy(ICP-AES) technique and phases, morphologies and particle sizes of those were investigated by Raman Spectroscopy, X-ray diffraction(XRD), Scanning Electron Microscopy(SEM), Transmission Electron Microscopy(TEM) and Particle Size Analyzer(PSA) techniques.

• Clean Technology
• /
• v.7 no.4
• /
• pp.265-272
• /
• 2001

본 연구는 지구 온난화 현상의 주원인이 되는 $CO_2$ 를 화력발전소 연도가스로부터 분리 회수하기 위한 PSA 공정 개발용 기초자료를 습득하기 위하여 실시하였다. 연도가스와 유사한 조건하에서 국내에서 제조된 활성탄을 이용하여 이산화탄소 및 밸런스를 이루고 있는 질소 가스의 흡착평형 및 흡착속도 실험을 실시하였으며, 분석을 위하여 자체 제작한 장치(부피측정법) 및 TGA 장치를 각각 사용하였다. 이 연구에서 획득한 흡착등온선으로부터 사용된 흡착제가 이산화탄소의 분리에 적절한지 판단할 수 있었다. 또한, TGA에 의해 측정된 흡착속도 자료는 향후 사용될 흡착탑의 파과곡선 예측에 사용될 수 있다. 연구결과로부터 다음과 같은 사실을 알 수 있었다. 첫째, 낮은 흡착온도 일수록 흡착량이 많고 빠른 흡착속도를 나타내었다. 둘째, 압력이 높아질수록 흡착량은 증가하였다. 셋째, SGT활성탄이 SGA-100 및 SGP-100활성탄 보다 다소 많은 흡착량과 빠른 흡착속도를 보였다.

• ETRI Journal
• /
• v.7 no.4
• /
• pp.11-14
• /
• 1985

A polysilicon self-aligned bipolar n-p-n transistor structure is described, which can be used in high speed and high packing density LSI circuits The emitter of this transistor is separated less than $0.4\mum$ with base contact by polysilicon self-align technology. Through all the process, the active region of this device is not damaged. therefore a high performance device is obtained. Using the transistor with $3.0\mum$ design rules, a CML ring oscillator has per-gate minimum propagation delay time of 400 ps at 2.7 mW power consumption condition.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1810-1815
• /
• 2003

Tube hydroforming provides a number of advantages over conventional stamping process, including fewer secondary operation, weight reduction, assembly simplification, adaptability to forming of complex structural components and improved structural strength and stiffness. In this study, the effect of the heat treatment on the hydro-formability has been investigated. By using the mild steel tube bulging test is performed at various heat treatment conditions to evaluate the hydro-formability.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.813-820
• /
• 2015

We have studied commercialization and process optimization of protective film on transparent conductive coated substrate, nano silver on flexible PET (poly ethylene terephthalate), by means of roll-to-roll micro-gravure coater. Nanosilver on flexible PET substrate is potential materials to replace ITO (indium tin oxide). Protective film is most important to maintain unique silver pattern on top of transparent PET. PSA pressure sensitive adhesives) was developed solely for nano silver on PET and protective film was successfully laminated. We have optimized all process conditions such as coating thickness, line speed and aging time & temperature via experimental design. Transparent conductive film and its protective film developed in this research are commercially available at this moment.

• Journal of Institute of Convergence Technology
• /
• v.12 no.1
• /
• pp.19-23
• /
• 2022

Interest in hydrogen production to respond to climate change is increasing. Until now, hydrogen has been mainly produced through the SMR (Steam Methane Reforming) process using natural gas. A large amount of CO₂ is emitted in the hydrogen production process through SMR, and the gas flow including CO₂ generated in the SMR process has different characteristics for each emission source, so it is important to apply a suitable CO₂ capture process. In the case of PSA tail gas or synthesis gas, the applicability of an amine-based process has been confirmed or demonstrated close to a commercial level. However, in the case of the flue gas generated from the reformer, it is still difficult to apply the conventional amine-based process because the partial pressure of CO₂ is relatively low. Energy-saving innovative absorbents such as phase separation absorbents can be a solution to these difficulties.

• Resources Recycling
• /
• v.19 no.5
• /
• pp.58-67
• /
• 2010

Platy silver powders with varied size and thickness were prepared by polyol process with $PdCl_2$ in ethylene glycol and characterized its properties and investigated the effects of reaction time, $NH_4OH$, PVP(poly-vinylpyrrolidone) and $PdCl_2$. The characteristics of the products were verified by scanning electron microscopy(SEM), high resolution transmitted electron microscopy(HR-TEM), X-ray diffraction(XRD) and particle size analyzer(PSA) and image analyzer. Platy silver powder was prepared about $5.5\;{\mu}m$ of size and $0.2\;{\mu}m$ at 120minute. It was found that the size of powders increased by the increasing of $NH_4OH$ and $PdCl_2$ concentrations, and the thickness of powders was decreased by increasing of PVP concentration.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.3
• /
• pp.1-8
• /
• 2005

Increase in the utilization rate of recycled paper and closing level of papermaking system increased the problem associated with stickies that include decrease in process runnability and product quality. It is required to establish a process for removing the micro stickies to solve the problems associated with stickies. In this study, the application of flotation process as a method to remove micro stickies was examined. Model micro stickies (MMS) were prepared using microcrystalline cellulose (MCC) and pressure sensitive adhesives (PSA), and the influence of three nonionic surfactants on the removal efficiency of MMS from flotation process was examined. Also the effect of surfactants on the deposition of micro stickies that remaining in the papermaking wet end onto wire was examined. Removal efficiency of MMS by flotation was increased when the proportion of nonionic surfactant with propylene oxide (PO) type hydrophilic tail was increased and stock pH was 7. It was suggested that this nonionic surfactant minimized the increase of surface energy of hydrophobic MMS. The MMS with high hydrophobicity remaining in the papermaking system, however, would cause more serious deposition problems on papermaking wet end. Therefore, it is of great importance to increase the removal efficiency of MMS in flotation process for the prevention of papermaking system contamination caused by stickies deposition.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.76-83
• /
• 2005

화석연료의 점진적인 고갈과 그 사용에 따라 발생하는 환경오염 문제의 해결 및 에너지 안보 차원에서 세계 각국은 수소경제로의 이동을 준비 중이며 현재 기술개발을 통해 상업화의 시기를 앞당기는 노력을 하고 있다. 국내에서는 2003년부터 본격적으로 정부 주도의 기술개발 및 실용화 사업을 추진하고 있으며 민간 부문에서는 국내 대기업들을 위주로 해외 전문업체와의 제휴를 통해 차세대 수종 사업으로 수소 연료전치 기술개발을 추진 중이나, 아직까지 기술력이 세계수준에는 이르지 못하고 있는 실정이다. SK는 산업자원부와 에너지관리공단에서 주관하는 대체에너지 기술개발 사업 중 수소연료전지 분야의 '수소스테이션(Hydrogen Station) 국산화 기술개발' 사업의 주관 기관으로서, 독자 기술로 개발한 수소 발생 장치를 중심으로 하여 2007년 수소스테이션 건설을 목표로 연구를 수행하고 있다. 수소스테이션 국산화 기술 개발은 2004년부터 2009년까지 총 5년간에 걸쳐 진행되며, 주관 연구기관인 SK는 수소 발생 장치의 개발과 이를 중심으로 한 수소스테이션의 건설을 총괄하고 있으며, 3개 국책 연구 기관 및 4개 대학이 위탁연구 기관으로 참여하여, 수소 생산 신공정 개발, 촉매 개발, PSA개발 및 탈항 기술 개발 등에 대한 요소 기술의 국산화를 목표로 연구를 진행하고 있다. 본 고에는 2004년부터 현재까지의 주요 연구 결과 및 수소스테이션 건설 추진 현황을 소개하고자 한다.

• Korean Journal of Materials Research
• /
• v.27 no.2
• /
• pp.82-88
• /
• 2017

Ink-jet printing techniques with ceramic ink, which contains ceramic pigments as colorant, are in increasingly use in the ceramic industry. Generally, ceramic pigments that are produced by conventional method show diameters of several micrometers; these micrometer sized particles in the ink-jet printing process can cause undesirable behavior such as print head nozzle clogging. To prevent this problem, a particle size reduction process is required. In this study, CMYK (cyan, magenta, yellow, black) pigments were synthesized via solid state method. Each pigment particle was milled to submicron size by an attrition mill. The effects of micronizing on the morphology, mechanical property, crystal structure and color property of the CMYK ceramic pigments were investigated by field emission scanning electron microscopy (FE-SEM), particle size analysis (PSA), X-ray diffraction (XRD) and CIE $L^{\ast}a^{\ast}b^{\ast}$.