• Journal of the Korean Professional Engineers Association
• /
• v.28 no.4
• /
• pp.54-75
• /
• 1995

This synthesis has been prepared from a review of literature on Truck Escape Ramps technology and a survey of current practice by state department of transportation. Their locations have been determined usually from a combination of accident experience and en-gineering judgement, but new tools are emerging that can identify needs and sites without waiting for catastrophic accidents to happen. The Grade Severity Rating Systems holds promise in this regard. Design Procedures for truck excape ramps continue to evolve. Gravel arrester beds are clearly the preferred choice across the country Rounded aggregate, uniformly graded in the approximate size range of 13 to 18mm. Tech-nical publications typically have dassified TER types as paved gravity, sandpile, and ar-rester bed ramps. The design speed for vehicle entry into the ramp in critical to the deter-mination of ramp length. An escape ramp should be designed for a minimum entry speed of 130km/hr, a 145km/hr design being preferred. The ramps should be straight and their angle to the roadway align-ment should be as possible. The grade of truck escape ramps show the adjustment of ramp design to local topography, such as the tradeoff of ramp length against earthwork requirements. A width of 9 to 12m would more safety acommodate two or more outof con-trol vehicles. Reguarding comments on the most effective material, most respondents cited their own specification or referred to single graded, rounded pea gravel. The consensus essentially Is that single graded, well -rounded gravel is the most desirable material for use in arrester beds. The arrester beds should be constructed with a minimum aggregate depth of 30cm. Successful ramps have used depths between 30 and 90cm.

• Korean Chemical Engineering Research
• /
• v.44 no.6
• /
• pp.588-596
• /
• 2006

The surface of polystyrene membrane treated by Ar, $O_2$ plasma, and the effects were observed before and after the treatment and permeability of $CO_2$, $N_2$ and selectivity of $CO_2$ relative to $N_2$ was measured using continuous flow gas permeation analyzer (GPA). The mole ratio of O over C in the surface was increased from 0 to 0.179 with Ar plasma treatment and route mean square of surface was increased from $15.86{\AA}$ to $71.64{\AA}$. Therefore the contact angle was decreased from $89.16^{\circ}$ to $18.1^{\circ}$. Thus Plasma treatments made surface of membrane tend to be highly hydrophilic. The optimum condition for the $CO_2$ permeability and ideal selectivity of the plasma treated membrane was as follows: the measurement of Ar (60 W, 2 min, $70^{\circ}C$) plasma treatment was $1.14{\times}10^{-12}[m^3(STP){\cdot}m/m^2{\cdot}sec{\cdot}atm]$ and 4.22. In the case of $O_2$ plasma treatment, the contact angle was decreased at $13.56^{\circ}$ with increase of O/C ratio ($0.189{\AA}$) and route mean square of surface ($57.10{\AA}$). The optimum condition for the $CO_2$ permeability and ideal selectivity of the plasma treated membrane was as follows: the measurement of $O_2$ (90 W, 2 min, $70^{\circ}C$) plasma treatment was $7.1{\times}10^{-12}[m^3(STP){\cdot}m/m^2{\cdot}sec{\cdot}atm]$ and 11.5. After plasma treatment, the changes of membrane surface were all subtly linked with both cross-linking and etching effects. Finally, it was confirmed that the gas permeation capacity and selectivity of the modified membrane with plasma could be improved by an appropriate control of the plasma conditions such as treatment time, the power input and sort of plasma gas.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.6
• /
• pp.815-824
• /
• 2022

Among the main facilities of the power plant, the circulating water used for cooling the power generation system is supplied through the Circulation Water Intake Basin (CWIB). The vortexes of various types generated in the Pump Sump (PS) of CWIB adversely affect the Circulation Water Pump (CWP) and pipelines. In particular, the free surface vortex accompanied by air intake brings about vibration, noise, cavitation etc. and these are the causes of degradation of CWP performance, damage to pipelines. Then power generation is interrupted by the causes. Therefore, it is necessary to investigate the hydraulic characteristics of CWIB through the hydraulic model experiment and apply an appropriate Anti Vortex Device (AVD) that can control the vortex to enable smooth operation of the power plant. In general, free surface vortex is controlled by Curtain Wall (CW) and the submerged vortex is by the anti vortex device of the curtain wall. The detailed specifications are described in the American National Standard for Pump Intake Design. In this study, the circulating water intake part of the Tripoli West 4×350 MW power plant in Libya was targeted, the actual operating conditions were applied, and the vortex reduction effect of the anti vortex device generated in the suction tank among the circulating water intake part was analyzed through a hydraulic model experiment. In addition, a floor splitter was basically applied to control the submerged vortex, and a new type of column curtain wall was additionally applied to control the vortex generated on the free surface to confirm the effect. As a result of analyzing the hydraulic characteristics by additionally applying the newly developed Column Curtain Wall (CCW) to the existing curtain wall, we have found that the vortex was controlled by forming a uniform flow. In addition, the vortex angle generated in the circulating water pump pipeline was 5° or less, which is the design standard of ANSI/HI 9.8, confirming the stability of the flow.

• Journal of Food Hygiene and Safety
• /
• v.38 no.2
• /
• pp.37-45
• /
• 2023

The surge in food delivery systems during the coronavirus 2019 pandemic necessitated this study of heavy metal migration from food contact materials (FCMs). A total of 104 samples of FCMs, comprising 51 polypropylene (PP), 21 polyethylene (PE), and 32 polystyrene (PS) samples of six different types of FCMs (containers, covers, table utensils, cups, pouches, and wrappers) used for food delivery distributed in Korea, were collected and investigated for migration of three heavy metals (Pb, Cd, and As) using inductively coupled plasma-mass spectrometry (ICP-MS) to determine whether they complied with Korea's Standards and Specifications for Utensils, Containers, and Packages. Acetic acid (4%, v/v) was used as the food simulant, and tests were performed at 100℃ (in harsh conditions) for 30 min. Linearity of Pb, Cd, and As showed acceptable results with a coefficient of determination (R²) value of 0.9999. Limit of detection (LOD) and limit of quantification (LOQ) of Pb, Cd, and As were 0.001, 0.001, and 0.001 ㎍/L and 0.002, 0.003, and 0.003 ㎍/L, respectively. Accuracy and precision results complied with the criteria presented in the European Commission Joint Research Centre guidelines. The average concentration of Pb, Cd, and As migration detected in a total of 104 samples was 0.009-0.260 ㎍/L, which was very low compared with the migration specification set in the Standards and Specifications for Utensils, Containers, and Packages. The maximum level of Pb corresponded to 0.23% of the migration limit. There were no samples exceeding the limit. Thus, this study confirmed that the heavy metal contents of FCMs used for delivery food distributed in Korea were safely managed. The data from this study represent an invaluable source for science-based safety management of hazardous heavy metals migrating from FCMs used in the food delivery industry.

• Radiation Oncology Journal
• /
• v.20 no.2
• /
• pp.116-122
• /
• 2002

Purpose : A randomized prospective study was conducted to compare the efficacy of early or late alternating schedules of radiotherapy, and carboplatin and ifosfamide chemotherapy in patients with limited-disease small cell lung cancer. Materials and Methods: From August 1993 to August 1996, a total of 44 patients with newly diagnosed, limited-disease small cell lung cancer, PS $H0\~2$, wt $loss<10\%$ were enrolled in a randomized trial which compared early alternating radiotherapy (RT)/chemotherapy (CT) and late alternating RT/CT. The CT regimen included ifosfamide $1.5\;g/m^2$ IV, d1-5 and carboplatin AUC 5/d IV, d2 peformed at 4 week intervals for a total of 6 cycles. RT (54 Gy/30 fr) was started after the first cycle of CT (early arm, N=22) or after the third cycle of CT (late arm, N=22) with a split course of treatment. Results : The pretreatment characteristics between the two arms were well balanced. The response rates in the early $(86\%)$ and late $(85\%)$ arm were similar. The median survival durations and 2-year survival rates were 15 months and $22.7\%$ in the early arm, and 17 months and $14.9\%$ in the late arm (p=0.47 by the log-rank test). The two-year progression free survival rates were $19.1\%$ in the early arm and $19.6\%$ in the late arm (p=0.52 by the log-rank test). Acute grade 3 or 4 hematologic and nonhematologic toxicities were similar between the two arms. Eighteen patients $(82\%)$ completed 6 cycles of CT in the early arm and 17 $(77\%)$ in the late arm. Four patients received less than 45 Gy of RT in the early arm and two in the late arm. There was no significant difference in the failure patterns. The local failure rate was $43\%$ in the early arm and $45\%$ in the late arm. The first site of failure was the brain in $24\%$ of the early arm patients compared to $35\%$ in the late arm (p=0.51). Conclusion : There were no statistical differences in the overall survival rate and the pattern of failure between the early and late alternating RT/CT in patients with limited-disease small cell lung cancer.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.2
• /
• pp.169-181
• /
• 2007

Statement of problem: Titanium is well known as a proper metal for the dental restorations, because it has an excellent biocompatibility, resistance to corrosion, and mechanical property. However, adhesion between titanium and dental porcelains is related to the diffusion of oxygen to the reaction layers formed on cast-titanium surfaces during porcelain firing and those oxidized layers make the adhesion difficult to be formed. Many studies using mechanical, chemical and physical methods to enhance the titanium-ceramic adhesion have been actively performed. Purpose: This study meant to comparatively analyse the adhesion characteristics depending on different titanium surface coatings after coating the casts and wrought titanium surfaces with Au and TiN. Material and method: In this study, the titanium specimens (CP-Ti, Grade 2, Kobe still Co. Japan) were categorized into cast and wrought titanium. The wrought titanium was cast by using the MgO-based investment(Selevest CB, Selec). The cast and wrought titanium were treated with Au coating($ParaOne^{(R)}$., Gold Ion Sputter, Model PS-1200) and TiN coating(ATEC system, Korea) and the ultra low fusing dental porcelain was fused and fired onto the samples. Biaxial flection test was done on the fired samples and the porcelain was separated. The adhesion characteristics of porcelain and titanium after firing and the specimen surfaces before and after the porcelain fracture test were observed with SEM. The atomic percent of Si on all sample surfaces was comparatively analysed by EDS. In addition, the constituents of specimen surface layers after the porcelain fracture and the formed compound were evaluated by X-ray diffraction diagnosis. Result: The results of this study were obtained as follows : 1. The surface characteristics of cast and wrought titanium after surface treatment(Au, TiN, $Al_2O_3$ sandblasting) were similar and each cast and wrought titanium showed similar bonding characteristics. 2. Before and after the biaxial flection test, the highest atomic weight change of Si component was found in $Al_2O_3$ sandblasted wrought titanium(28.6at.% $\rightarrow$ 8.3at.%). On the other hand, the least change was seen in Au-Pd-In alloy(24.5at.% $\rightarrow$ 9.1at.%). 3. Much amount of Si components was uniformly distributed in Au and TiN coated titanium, but less amount of Si's was unevenly dispersed on Al2O3 sandblasting surfaces. 4. In X-ray diffraction diagnosis after porcelain debonding, we could see $Au_2Ti$ compound and TiN coating layers on Au and TiN coated surfaces and $TiO_2$, typical oxide of titanium, on all titanium surfaces. 5. Debonding of porcelain on cast and wrought titanium surface after the biaxial flection is considered as a result of adhesion deterioration between coating layers and titanium surfaces. We found that there are both adhesive failure and cohesive failure at the same time. Conclusion: These results showed that the titanium-ceramic adhesion could be improved by coating cast and wrought titanium surfaces with Au and TiN when making porcelain fused to metal crowns. In order to use porcelain fused to titanium clinically, it is considered that coating technique to enhance the bonding strength between coating kKlayers and titanium surfaces should be developed first.

• Journal of Food Hygiene and Safety
• /
• v.13 no.3
• /
• pp.221-231
• /
• 1998

The biosynthesis of galactolipid and the composition of fatty acid in chloroplast and thylakoid envelope isolated from C. ellipsoidea treated with antiseptics (potassium sorbate: PS, sodium benzoate:SB, calcium propionate:CP) were analyzed. The contents of monogalactosyldiacylglycerol (MGDG), digalactosyldiacylglycerol (DGDG) and total lipid in treatment with antiseptics were lower to compared with the control. The major fatty acid utilized for biosynthesis of MGDG in chloroplast envelope were palmitoleic acid (ave. 15.55%), oleic acid (ave. 15.09%) in control. Otherwise, the major fatty acids in P.S treatment were utilized for oleic acid (ave. 13.71%), linolenic acid (ave. 14.36%), palmitoleic acid (ave. 18.26%), oleic acid (ave. 17.26%) in S.B treatment, and oleic acid (ave. 16.88%), palmitoleic acid (ave. 16.31%) in CP treatment. It was showed that the major fatty acids in chloroplast envelope DGDG were oleic acid (ave. 15.75%), linolenic acid (ave. 17.74%) in control, oleic acid (ave. 14.90%), palmitoleic acid (ave. 15.97%) in P.S treatment, palmitoleic acid (ave. 13.29%), oleic acid (ave. 15.74%) in S.B treatment, and oleic acid (ave. 14.52%), palmitoleic acid (ave. 14.03%) in C.P treatment. The major fatty acid utilized for biosynthesis of MGDG in thylakoid envelope were linolenic acid (ave. 14.78%), oleic acid (ave. 12.90%) in control. Otherwise, the major fatty acids were utilized for palmitoleic acid (ave. 13.00%), palmitic acid (ave. 13.00%) in P.S treatment, palmitoleic acid (ave. 12.94%), oleic acid (ave. 12.43%) in S.B treatment, and oleic acid (ave. 12.43%), palmitoleic acid (ave. 12.43%) in C.P treatment. It was showed that the major fatty acids in thylakoid envelope DGDG were linolenic acid (ave. 18.01 %), oleic acid (ave. 15.53%) in control, linolenic acid (ave. 19.20%), linoleic acid (ave. 14.14%) in P.S treatment, palmitoleic acid (ave. 9.03%), oleic acid (ave. 14.85%) in S.B treatment, oleic acid (ave. 13.90%), linolneic acid(ave. 12.66%) in C.P treatment.

• Korean Journal of Soil Science and Fertilizer
• /
• v.33 no.4
• /
• pp.234-241
• /
• 2000

Organic farming (OF) is regarded as alternative farming types against general farming system for sustainable agriculture, recently. However, there is little information on effects of OF on soil properties and watershed condition. In order to determine the effects of OF on soil properties, 36, 10 and 8 sites of organic farming (OF) fields of plastic film houses, paddy and orchard were selected in the national scale, respectively, to evaluate their chemical properties and phosphorus distributing characteristics. The average organic matter (OM) contents in organic farming fields were with $44g\;kg^{-1}$ in plastic film houses, $26g\;kg^{-1}$ in paddies and $39g\;kg^{-1}$ in orchard soils higher than the average OM contents in conventional farming (CF) soils. Available phosphates were accumulated to 986 in plastic film house soils and $754mg\;kg^{-1}$ in orchard soils, respectively, over the optimum range. Furthermore, total P (T-P) reached to $2.973mg\;kg^{-1}$ in plastic film houses and $2303mg\;kg^{-1}$ in orchards in OF soils. It could be attained by applying repeatedly low N/P ratio of manure-based compost. In two types of soils inorganic P was dominant with the ratio of 62~80% of T-P, and then residual and organic Ps followed. However. residual-P was dominant in paddy soils with the rate of 50% of T-P. Fractionation of soil extractable P showed that Ca-P was dominant with about $1,330mg\;kg^{-1}$ in upland soils in OF fields, which is affected by high soil pH of over 6.0. However. Fe-P of extractable P was dominant in paddy soils. Water-soluble P was very high with 65 and $26mg\;kg^{-1}$ in plastic film house and orchard soils in OF. From this results. OF regarded as an environment-friendly farming system may cause serious soil deterioration by accumulated phosphorus and may also cause water pollution.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.42 no.6
• /
• pp.941-947
• /
• 2013

To increase the consumption of frying ginseng, we investigated the physicochemical properties of frying ginseng and different edible oils processed through frying ginseng: soybean oil (SO), corn oil (CO), olive oil (OO), and grape seed oil (GO). We tested various parameters, including temperature (130, 160, 180, and $200^{\circ}C$), frying time (2.0, 2.5, 3.0, and 3.5 min), and frying amount (up to 30 times). The physicochemical properties of the fried ginseng and oils were evaluated for changes in acid value, peroxide value, free fatty acid content, acrylamide formation, color, and viscosity of oils. The acid value and peroxide value of the oils increased with frying temperature and amount. Saturated fatty acids increased and unsaturated fatty acids decreased with the amount of frying, but oleic acid in CO and GO and linoleic acid in OO increased. The concentration of acrylamide in fried ginseng increased as the frying temperature and amount increased and was the lowest in OO. The lightness and redness of the frying oil color decreased and its yellowness increased in SO and CO, but the lightness increased (redness and yellowness decreased) in OO. In particular, CO was significantly browned with increasing frying amounts. The viscosity of the frying oils increased with frying amount, with CO showing the lowest increases in viscosity of the oils. As a result, the optimal ginseng frying condition found was 2 min 30 sec at $180^{\circ}C$, regardless the type of oils.

• Tuberculosis and Respiratory Diseases
• /
• v.46 no.4
• /
• pp.500-511
• /
• 1999

Background: Noninvasive positive pressure ventilation (NPPV) using facial or nasal mask have been widely used for several years in stable patients with chronic neuromuscular disease or central alveolar hypoventilation, and recently have been tried in patients with acute respiratory failure. In a few studies, NPPV was also used to rescue the patients with post-extubation respiratory failure. However, yet it has not been adopted as a weaning method in patients on long-term mechanical ventilation. So we performed this prospective clinical study to evaluate the usefulness of NPPV as a weaning method after removing endotracheal tube intentionally in patients on long-term mechanical ventilation. Method: Twelve patients who had been on invasive mechanical ventilation over 10 days were enrolled and 14 trials of NPPV were done. All had failed at least one weaning trial and showed ventilator dependence(pressure support requirement between 8-15cm $H_2O$, and PEEP requirement between 5-10cm $H_2O$), so tracheostomy was being considered. After removing the endotracheal tube, NPPV was applied using facial mask. Respiratory rate, arterial blood gas, pressure support level, and PEEP level were monitored just before intended extubation, at 30 minutes, 1 to 6, 6 to 12, 12 to 24 hours, 2nd day, and 3rd day following initiation of NPPV, and just before weaning from NPPV. The successful weaning was defined as spontaneous breathing off the ventilator for 48 hours or longer without respiratory distress. Results: The weaning through NPPV after intended extubation was successful in 7(50%) of 14 trials, and tracheostomy could be avoided in them. There were no differences in age, sex, APACHE III score, duration of invasive mechanical ventilation, baseline respiratory rate, $PaCO_2$ $PaO_2/FiO_2$, and ventilatory requirement(PS and PEEP) between the success and failure groups. In the success group, respiratory rate, pH, $PaCO_2$, and $PaO_2/FiO_2$ were not different between invasive MV and NPPV period. But in the failure group, pH decreased after 30 minutes of NPPV initiation compared with that of invasive MV($7.40\pm0.08$ vs. $7.34\pm0.06$, p<0.05). The causes of failure were worsening of ABG(n=3), retained tracheal secretion(n=2), mask intolerance(n=1), and flail chest(n=1). Conclusion: NPPV may be worth trying as a bridge method in weaning patients on long-term invasive mechanical ventilation.