• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.885-888
• /
• 2000

The effects of deposition temperature and post annealing process of ferroelectric PbZr$\sub$0.52/Ti$\sub$0.48/O$_3$(PZT) thin films by pulsed laser deposition (PLD) were investigated. The PZT thin films were deposited at 400, 450, 500, and 550$^{\circ}C$, with/without post annealing at 650$^{\circ}C$ for 30 min. The PZT thin films deposited above 500$^{\circ}C$ without post annealing were crystallized into peroveskite phase, but the PZT thin films deposited below 450$^{\circ}C$ had pyrochlore phase. The PZT thin films deposited below 450$^{\circ}C$ with post annealing also crystallized into pure perovskite. Compared to the PZT thin films which were deposited at 450$^{\circ}C$ and post annealed, the films deposited at 550$^{\circ}C$ have a columnar microstructure and high remnant polarization 28 (${\mu}$C/cm$^2$). With in-situ annealing at oxygen ambient, the PZT thin films reduced oxygen vacancies and increased retained polarization.

• 한국결정성장학회지
• /
• 제13권4호
• /
• pp.157-164
• /
• 2003

$LaF_{3}$ thin films have been fabricated on Si (100) substrates under the highest possible vacuum condition by pulsed laser deposition (PLD) method. The temperature of the sbustrate varied from $20^{\circ}C$ to $800^{\circ}C$. The films deposited at the higher temperature indicated the sharper peaks in the X-ray diffraction measurement. A highly oriented film was successfully obtained at a substrate temperature of $800^{\circ}C$. The surface observation by the AFM revealed that the many hexagonal structures constructed the film. The XPS analysis revealed that the lacking of F in the film deposited at $600^{\circ}C$ were much more than that in film at $^20{\circ}C$. Adding the adequate amount of $CF_{4}$ gas in the growth chamber can compensate this lacking of F.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 디스플레이 광소자 분야
• /
• pp.38-41
• /
• 2002

The variation of photoluminescence(PL) properties of Si thin films was investigated by changing deposition temperatures, Si-rich silicon oxide films on p-type (100) Si substrate have been fabricated by pulsed laser deposition(PLD) technique using a Nd:YAG laser. During deposition, the substrates were kept at the temperature range of room temperature(RT) to $400^{\circ}C$. After deposition, samples were annealed at $800^{\circ}C$ in nitrogen ambient, Strong Blue PL has been observed on RT-deposited Si nanocrystallites. When the deposition temperature was increased over $100^{\circ}C$, PL intensities abruptly decreased. The experimental results show the growing mechanism of Si nanocrystallites by PLD.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.264-266
• /
• 2005

Manufacture of OLED device used thermal evaporation method. However thermal evaporation method has many defect as thermal damage of substrate, difficult of dopant rate control and low utilization of organic materials. so we suggest PLD(Pulsed Laser Deposition) method that solution of these problems. PLD method has many advantage as without thermal damage, easy indicate of deposition rate per one pulse and good utilization of organic materials. In this paper we apply the PLD method for manufacture of device so we present high efficiency device manufacture using PLD method that has good deposition uniformity, surface rough and deposition rate.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.207-207
• /
• 2010

Both ZnO and GaN have excellent physical properties in optoelectronic devices such as blue light emitting diode (LED), blue laser diode (LD), and ultra-violet (UV) detector. The ZnO/GaN heterostructure, which has a potential to achieve the cost efficient LED technology, has been fabricated by using radio frequency (RF) sputtering, pyrolysis, metal organic chemical vapor deposition (MOCVD), direct current (DC) arc plasmatron, and pulsed laser deposition (PLD) methods. Among them, the PLD system has a benefit to control the composition ratio of the grown film from the mixture target. A 500-nm-thick ZnO film was grown by PLD technique on c-plane GaN/sapphire substrates. The post annealing process was executed at some varied temperature between from $300^{\circ}C$ to $900^{\circ}C$. The morphology and crystal structural properties obtained by using atomic force microscope (AFM) and x-ray diffraction (XRD) showed that the crystal quality of ZnO thin films can be improved as increasing the annealing temperature. We will discuss the post-treatment effect on film quality (uniformity and reliability) of ZnO/GaN heterostructures.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.41-42
• /
• 2005

The characteristics of ZnO films are reported depending on different deposition conditions for film bulk acoustic resonators (FBARs). The ZnO films have been deposited on Al films evaporated on p-type (100) silicon substrate by pulsed laser deposition (PLD) technique using a Nd:YAG laser. These films exhibit an electrical resistivity higher than $10^7$ $\Omega$m. X-ray diffraction measurements have shown that ZnO films are highly c-axis oriented with full width at half maximum (FWHM) below $0.5^{\circ}$. These results show the possibility of FBAR devices using by PLD.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.207-210
• /
• 2005

In order to investigate the influence of the homo buffer layer on the microstructure of the ZnO thin film, undoped ZnO buffer layer were deposited on sapphire (0001) substrates by ultra high vaccum pulsed laser deposition (UHV-PLD) and molecular beam eiptaxy (MBE). After high temperature annealing at $600^{\circ}C$ for 30min, undoped ZnO buffer layer was deposited with various oxygen pressure (35~350mtorr). On the grown layer of undoped ZnO, Arsenic-doped(l, 3wt%) ZnO layers were deposited by UHV-PLD. The optical property of the ZnO was analyzed by the photoluminescence (PL) measurement. From $\Theta-2\Theta$ XRD analysis, all the films showed strong (0002) diffraction peak, and this indicates that the grains grew uniformly with the c-axis perpendicular to the substrate surface. Field emission scanning electron microscope (FE-SEM) revealed that microstructures of the ZnO were varied with oxygen pressure, arsenic doping level, and the deposition method of undoped ZnO buffer layers. The films became denser and smoother in the cases of introducing MBE-buffer layer and lower oxygen pressure during As-doped ZnO deposition. Higher As-doping concentration enhanced the columnar-character of the films.

• 한국결정성장학회지
• /
• 제13권2호
• /
• pp.79-82
• /
• 2003

ArF(193nm) 엑시머 레이저를 이용한 펄스레이저증착법(PLD)에 의해 GaN 소결체를 타겟 재료로 하여 $SiO_2$기판위에 GaN nanoparticles를 합성하였다. PLD 공정 중에는 100Pa, 50Pa, 10Pa및 1 Pa의 Ar gas 압력과 100mJ 및 200mJ의 레이저 에너지를 가하였다. 합성된 GaN nanoparticles는 XRD, SEM, TEM, XPS 및 optical absorption spectra 등에 의해 분석되었다. 합성된 GaN nanoparticles는 대체적으로 20~30nm의 입경을 갖는 균일한 분포를 하고 있었다. 또한, Ar 기체 압력이 낮아짐에 따라 합성된 GaN nanoparticles의 stoichiometry가 향상되고 optical band edge가 blueshift 경향을 나타내었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.355-357
• /
• 2001

ZnO thin films were deposited on (001) sapphire substrate at various ambient gas pressure by pulsed laser deposition(PLD). Oxygen was used as ambient gas, and oxygen gas pressure was varied from 1.0${\times}$10$\^$-6/ Torr to 500 mTorr during the film deposition. As oxygen gas pressure increase in the region below critical pressure photoluminescence(PL) intensity in UV and green region increase. As oxygen gas pressure increase in the region above critical pressure photoluminescence(PL) intensity in UV and green region decrease. Each of critical ambient gas Pressures was 350 mTorr for UV emission and 200 mTorr for green emission.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권1호
• /
• pp.26-29
• /
• 2006

Transparent ZnO thin films were prepared by KrF pulsed laser deposition (PLD) technique and applied to a bottom-gate type thin film transistor device as an active channel layer. A high conductive crystalline Si substrate was used as an metal-like bottom gate and SiN insulating layer was then deposited by LPCVD(low pressure chemical vapour deposition). An aluminum layer was then vacuum evaporated and patterned to form a source/drain metal contact. Oxygen partial pressure and substrate temperature were varied during the ZnO PLD deposition process and their influence on the thin film properties were investigated by X-ray diffraction(XRD) and Hall-van der Pauw method. Optical transparency of the ZnO thin film was analyzed by UV-visible phometer. The resulting ZnO-TFT devices showed an on-off ration of $10^6$ and field effect mobility of 2.4-6.1 $cm^2/V{\cdot}s$.