• 한국의학물리학회지:의학물리
• /
• 제30권4호
• /
• pp.155-159
• /
• 2019

Radiological properties of newly introduced and existing 3-dimensional (3D) printing materials were evaluated by measuring their Hounsfield units (HUs) at varying infill densities. The six materials for 3D printing which consisted of acrylonitrile butadiene styrene (ABS), a unique ABS plastic blend manufactured by Zortrax (ULTRAT), high impact polystyrene (HIPS), polyethylene terephthalate glycol (PETG), polylactic acid (PLA), and a thermoplastic polyester elastomer manufactured by Zortrax (FLEX) were used. We used computed tomography (CT) imaging to determine the HU values of each material, and thus assess its suitability for various applications in radiation oncology. We found that several material and infill density combinations resembled the HU values of fat, soft tissues, and lungs; however, none of the tested materials exhibited HU values similar to that of bone. These results will help researchers and clinicians develop more appropriate instruments for improving the quality of radiation therapy. Using optimized infill densities will help improve the quality of radiation therapy by producing customized instruments for each field of radiation therapy.

• 대한방사선기술학회지:방사선기술과학
• /
• 제41권1호
• /
• pp.53-60
• /
• 2018

The purpose of this study was investigating the effect of 3D printing technology that changes the speed of sound (SOS) and the broadband ultrasound attenuation (BUA) by controlling the density of the media phantom. We used 3D printers which called additive manufacturing (AM) by using material with polylactic acid (PLA). The inside of the medium phantom was filled crossly with 100%, 90%, 80%, 70%, 60%, and 50% of the material. The ultrasonic instrument measured the SOS and the BUA using a 0.55 MHz ultrasound output in opposing mode with a pair of transducers. As a result, the density of the medium phantoms with the SOS showed very high correlation (r = 0.944), but the SOS showed very low correlation (r = 0.500). It is expecting that the manufacturing and measurement method of the medium phantom using 3D printing technology will be used as basic data for ultrasonic bone mineral density.

• Elastomers and Composites
• /
• 제58권1호
• /
• pp.44-56
• /
• 2023

Additive manufacturing (AM) or three-dimensional (3D) printing of metals has been drawing significant attention due to its reliability, usefulness, and low cost with rapid prototyping. Among the various AM technologies, fused deposition modeling (FDM) or fused filament fabrication is receiving much interest because of its simple manufacturing processing, low material waste, and cost-effective equipment. FDM technology uses metal-filled polymer filaments for 3D printing, followed by debinding and sintering to fabricate complex metal parts. An efficient binder is essential for producing polymer filaments and the thermal post-processing of printed objects. This study involved an in-depth investigation of and a fabrication route for a novel multi-component binder system with steel alloy powder (45 vol.%) ranging from filament fabrication and 3D printing to debinding and sintering. The binder system consisted of polyvinyl pyrrolidone (PVP) as a binder and thermoplastic polyurethane (TPU) and polylactic acid (PLA) as a carrier. The PVP binder held the metal components tightly by maintaining their stoichiometry, and the TPU and PLA in the ratio of 9:1 provided flexibility, stiffness, and strength to the filament for 3D printing. The efficacy of the binder system was examined by fabricating 3D-printed cubic structures. The results revealed that the thermal debinding and sintering processes effectively removed the binder/carrier from the cubic structures, resulting in isotropic shrinkage of approximately 15.8% in all directions. The scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) patterns displayed the microstructure behavior, phase transition, and elemental composition of the 3D cubic structure.

• 한국산업보건학회지
• /
• 제28권3호
• /
• pp.241-256
• /
• 2018

Objectives: This study aimed to review the characteristics of three-dimensional printing technology focusing on printing types, materials, and health hazards. We discussed the methodologies for exposure assessment on hazardous substances emitted from 3D printing through article reviews. Methods: Previous researches on 3D printing technology and exposure assessment were collected through a literature review of public reports and research articles reported up to July 2018. We mainly focused on introducing the technologies, printing materials, hazardous emissions during 3D printing, and the methodologies for evaluation. Results: 3D printing technologies can be categorized by laminating type. Fused deposition modeling(FDM) is the most widely used, and most studies have conducted exposure assessment using this type. The printing materials involved were diverse, including plastic polymer, metal, resin, and more. In the FDM types, the most commonly used material was polymers, such as acrylonitrile-butadiene-styrene(ABS) and polylactic acids(PLA). These materials are operated under high-temperature conditions, so high levels of ultrafine particles(mainly nanoparticle size) and chemical compounds such as organic compounds, aldehydes, and toxic gases were identified as being emitted during 3D printing. Conclusions: Personal desktop 3D printers are widely used and expected to be constantly distributed in the future. In particular, hazardous emissions, including nano sized particles and various thermal byproducts, can be released under operation at high temperatures, so it is important to identify the health effects by emissions from 3D printing. Furthermore, appropriate control strategies should be also considered for 3D printing technology.

• 한국방사선학회논문지
• /
• 제12권3호
• /
• pp.335-341
• /
• 2018

의료수준의 향상과 더불어 환자들의 첨단의료장비에 대한 기대수준이 증가하고 있으며 특히 자기공명영상(Magnetic Resonance Image : MRI)은 현재 모든 임상 분야에서 가장 핵심적인 영상진단 도구로서 사용되고 있다. 그러나 검사 중에 발생하는 심각한 소음으로 많은 환자가 심리적인 불안을 경험한다고 한다. 이에 본 연구에서는 자기공명영상검사실의 기존 헤드셋 흡음재에서 차음재를 추가한 헤드셋의 소음저감평가와 차음재별 영상 아티팩트(artifact) 유무를 알아보고자 하였다. 3D 프린팅한 헤드셋 내부에 흡음재(스펀지)와 차음재(아크릴판, 구리판, 3D copper plate)를 교차 배열하여 MRI 검사소음을 녹음하여 스피커로 같은 dB 값의 소음을 발생시키며 3D 프린팅 된 두부모형의 내부에 소음측정기로 dB 값을 측정하여 정량분석을 하며 자체 제작한 헤드셋을 물팬텀에 밀착시킨 후 MRI영상 아티팩트 유무를 검사한다. 드셋의 정량평가를 한 결과, 헤드셋 평균 dB 값은 81.8 dB로 나타났으며, 차음재를 추가한 헤드셋에서 가장 방음효과가 뛰어난 재료조합(구리, 아크릴판, 스펀지, 스펀지) 헤드셋의 평균 dB 값은 70.4 dB 값이 측정되었지만 MRI 시뮬레이션 결과 구리가 반자성체이기 때문에 아티팩트가 나타나 배제하였고 두 번째로 방음효과가 뛰어난 (스펀지, 아크릴판, e-copper plate, 스펀지) 헤드셋의 평균 dB 값은 70.6 dB 값이 측정되었고 MRI 시뮬레이션 결과 인공물 나타나지 않았다. 구리분말이 약 40%가 포함된 e-copper PLA로 출력한 재료를 동일하게 시뮬레이션을 한 결과 인공물 나타나지 않았으므로 3D 프린팅 재료의 사용이 적합하였고 구리보다 경제성이 우수하며 가공이 용이하므로 적합한 재료로 선정하였다. MRI관련 연구에 있어 3D 프린팅을 이용한 상호발전이 매우 기대된다.

• Tribology and Lubricants
• /
• 제39권6호
• /
• pp.250-255
• /
• 2023

This study applies various surface patterns to minimize material loss in construction equipment that is subject to severe wear due to sand, such as the wear-resistant steel plates of dump trucks or the teeth of excavators. The relationship between surface morphology and wear behavior is investigated using PLA+ polymer to observe the effect of the surface pattern. Five types of samples - smooth, concave, convex, wavy concave, and wavy convex designs - are created using a 3D printer. A wear experiment is conducted for a duration of 3 h using 6.5 kg of abrasive particles. The mass loss of the samples after the experiment is measured to assess the extent of wear. Additionally, the surface morphology of the samples before and after the experiment is analyzed using SEM and confocal microscopy. The study results reveal that the smooth design exhibits the highest wear loss, whereas the concave and wavy concave designs show relatively lower wear loss. The convex and wavy convex designs exhibit varying contact areas with the abrasive particles depending on the surface pattern, resulting in different levels of wear. Furthermore, a comparison between the experimental results and DEM simulations confirms the observed wear trends. This study reveals the relationship between wear damage according to surface pattern shape and is expected to be of substantial help in the analysis of wear and tear on agricultural and heavy equipment.

• 한국콘텐츠학회논문지
• /
• 제15권1호
• /
• pp.308-315
• /
• 2015

본 연구는 3D 프린터를 이용하여 통풍이 원활하고 위생적이며 선명한 방사선영상을 구할 수 있는 그물형 손목 부목을 제작하고자 하였다. 스캐너는 의료용 다중단층영상장치(MDCT)를 이용했으며, 3D 프린터 기기는 용융 적층 조형술(fused deposition modeling, FDM)의 프린팅 방식을 이용했다. 소재는 분해성 플라스틱 (poly lactic acid, PLA)을 사용하였다. 손목의 3 차원 볼륨렌더링은 MDCT에서 획득된 단층영상으로 구현하였다. 구현된 손목 3 차원 영상을 바탕으로 가상의 그물형 부목 모형을 디자인하고 출력하였다. 그 결과 3D 프린터로 출력된 부목이 기존 부목보다도 우수한 방사선 손목영상을 획득할 수 있었으며 가려움증 및 비위생적인 단점을 개선하고 부목 해체 작업이 용이하였다. 결론적으로 본 연구에서 모델링된 3D 부목 모형은 향후 3D 프린팅 부목 제작에 기초자료로 활용할 수 있으며 환자들의 실생활에 도움을 줄 것으로 기대한다.

• 한국의학물리학회지:의학물리
• /
• 제28권1호
• /
• pp.33-38
• /
• 2017

Creating individualized build-up material for superficial photon beam radiation therapy at irregular surface is complex with rice or commonly used flat shape bolus. In this study, we implemented a workflow using 3D printed patient specific bolus and describe our clinical experience. To provide better fitted build-up to irregular surface, the 3D printing technique was used. The PolyLactic Acid (PLA) which processed with nontoxic plant component was used for 3D printer filament material for clinical usage. The 3D printed bolus was designed using virtual bolus structure delineated on patient CT images. Dose distributions were generated from treatment plan for bolus assigned uniform relative electron density and bolus using relative electron density from CT image and compared to evaluate the inhomogeneity effect of bolus material. Pretreatment QA is performed to verify the relative electron density applied to bolus structure by gamma analysis. As an in-vivo dosimetry, Optically Stimulated Luminescent Dosimeters (OSLD) are used to measure the skin dose. The plan comparison result shows that discrepancies between the virtual bolus plan and printed bolus plan are negligible. (0.3% maximum dose difference and 0.2% mean dose difference). The dose distribution is evaluated with gamma method (2%, 2 mm) at the center of GTV and the passing rate was 99.6%. The OSLD measurement shows 0.3% to 2.1% higher than expected dose at patient treatment lesion. In this study, we treated Mycosis fungoides patient with patient specific bolus using 3D printing technique. The accuracy of treatment plan was verified by pretreatment QA and in-vivo dosimetry. The QA results and 4 month follow up result shows the radiation treatment using 3D printing bolus is feasible to treat irregular patient skin.

• 한국기계가공학회지
• /
• 제19권1호
• /
• pp.81-88
• /
• 2020

In this paper, the performances of the electrical characteristics of the Fused Deposition Modeling (FDM) 3D-printed flexible resistance sensor was evaluated. The FDM 3D printing flexible resistive sensor is composed of flexible-material thermoplastic polyurethane and a conductive PLA (carbon black conductive polylactic acid) polymer. While 3D printing, polymer filaments heat up quickly before being extruded and cooled down quickly. Polymers have poor thermal conductivity so the heating and cooling causes unevenness, which then results in internal stress on the printed parts due to the rapidity of the heating and cooling. Electrical resistance measurements show that the 3D-printed flexible sensor is unstable due to internal stress, so the 3D-printed flexible sensor resistance curve does not match the increases and decreases in the displacement curve. Therefore, annealing was performed to eliminate the mismatch between electrical resistance and displacement. Annealing eliminates residual stress on the sensor, so the electrical resistance of the sensor increases and decreases in proportion to displacement. Additionally, the resistance is lowered in comparison to before annealing. The results of this study will be very useful for the fabrication of various devices that employ 3D-printed flexible sensor that have multiple degrees of freedom and are not limited by size and shape.

• 한국기계가공학회지
• /
• 제14권4호
• /
• pp.62-72
• /
• 2015

Interest in three-dimensional (3D) printing processes has grown significantly, and several types have been developed. These 3D printing processes are classified as Selective Laser Sintering (SLS), Stereo-Lithography Apparatus (SLA), and Fused Deposition Modeling (FDM). SLS can be applied to many materials, but because it uses a laser-based material removal process, it is expensive. SLA enables fast and precise manufacturing, but available materials are limited. FDM printing's benefits are its reasonable price and easy accessibility. However, metal printing using FDM can involve technical problems, such as suitable component supply or the thermal expansion of the heating part. Thus, FDM printing primarily uses materials with low melting points, such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA) resin. In this study, an FDM process for enabling metal printing is suggested. Particularly, the nozzle and heatsink for this process are focused for stable printing. To design the nozzle and heatsink, multi-physical phenomena, including thermal expansion and heat transfer, had to be considered. Therefore, COMSOL Multiphysics, an FEM analysis program, was used to analyze the maximum temperature, thermal expansion, and principal stress. Finally, its performance was confirmed through an experiment.