• Journal of the Korean Institute of Telematics and Electronics
• /
• v.15 no.5
• /
• pp.13-18
• /
• 1978

A delay switching PLL (DSPLL) is proposed for improvement of the frequency acquisition Performance (pull-in range) while keeping a narrow bandwidth LPF. It has, between the phase detector and the LPF, just a simple RC delay circuit, a switch and another phase detector controlling the switching time. For the common second order PLL, the pull-in capability of the DSPLL is analyzed approximately, without considering additive white noise effect, and verified experimentally. It is shown that the delay switching extends the pull-in range significantly, as much as a half of lock-range. At the phase tracking mode, the delay switching does not function, to make the DSPLL be a normal PLL.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.602-605
• /
• 1999

We dried emitting layer of EL device at 30, 80, I20 and $150^{\circ}C$ for Ihr to investigate the effects to the emission characteristics of devices. PL intensity of P3HT thin film decreased with increasing the drying temperature. But, the EL intensity and stability of device with emitting layer dried at $150^{\circ}C$ were the best. We think it s because of absence of water and remaining solvent in P3HT emitting layer. So, We suggest that the drying temperature of emitting layer of EL device should be select slightly low temperature than its glass transition temperature.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.04a
• /
• pp.67-68
• /
• 2007

마그네트론 스퍼터링을 이용하여 사파이어 기판위에 $O_2$의 분압에 따른 성장된 ZnO박막의 특성에 대해 연구하였다. $O_2$의 분압은 $Ar/O_2$의 비율에 의해 조절을 하여 성장을 하였으며, $O_2$의 분압이 감소함에 따라 결정성이 좋아지는 결과를 얻었다. PL측정결과에서 순수한 Ar분위기에서 성장된 ZnO박막에서 UV 발광과 더불어 Deep 1evel에 기인하는 Green 발광을 보였고, UN-Visible spectroscopy 측정결과 순수한 Ar분위기를 제외한 샘플에서 $60{\sim}80%$의 투과도를 보였다. SEM과 TEM의 이미지를 통해 미세 힐락들을 관찰되었는데, 이로 인해 투과도의 저하 원인으로 분석된다.

• Journal of the Korean Applied Science and Technology
• /
• v.14 no.3
• /
• pp.79-87
• /
• 1997

In this study, MEH-PPV was synthesized and MEH-PPV and its mixtures with PMMA were deposited on substrates with Langmuir-Blodgett(LB) technique and their photoluminescent char acteristics were investigated using UV-Vis absorption spectroscopy, and photoluminescence(PL) measurements. The surface morphology of the LB films of MEH-PPV and its mixture with PMMA were investigated using Atomic Force Microscopy(AFM). Electroluminescent devices using LB films were fabricated with Al and ITO as a top and bottom electrode, respectively, and their I-V characteristics were investigated.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.7
• /
• pp.701-704
• /
• 2000

Fluorene and carbazole-containing distyrylarylene model and polymeric fluorophores were prepared by reacting 2,7-dibromo-9-butylfluorene and 3,6-dibromo-9-butylcarbazole with styrene and divinylbenzene using the Heck reaction for the chemiluminesc ence. The UV-vis absorbance, photoluminescence (PL) as well as the chemiluminescence (CL) characteristics of the model and polymeric fluorophores were measured. Sodium salicylate-catalyzed reaction of bis(2,4,6-trichlorophenyl)oxalate (TCPO) with hydrogen peroxide produced a strong chemiluminescent blue light emission with 439-489 nm in the presence of the fluorophore. The wave-length of CL light was similar to that of photoluminescence. The chemiluminescent intensity was decayed according to the exponential equation.The glow of CL maintained more than 12 hr and was visible with naked eye.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.8
• /
• pp.417-422
• /
• 2006

This paper presents the effect of driving waveform for piezoelectric bend mode inkjet printhead with optimized mechanical design. Experimental and theoretical studies on the applied driving waveform versus jetting characteristics were performed. The inkjet head has been designed to maximize the droplet velocity, minimize voltage response of the actuator and optimize the firing frequency to eject ink droplet. The head design was carried out by using mechanical simulation. The printhead has been fabricated with Si(100) and SOI wafers by MEMS process and silicon direct bonding method. To investigate how performance of the piezoelectric ceramic actuator influences on droplet diameter and droplet velocity, the method of stroboscopy was used. Also we observed the movement characteristics of PZT actuator with LDV(Laser Doppler Vibrometer) system, oscilloscope and dynamic signal analyzer. Missing nozzles caused by bubbles in chamber were monitored by their resonance frequency. Using the water based ink of viscosity of 4.8 cps and surface tension of 0.025 N/m, it is possible to eject stable droplets up to 20 kHz, 4.4 m/s and above 8 pl at the different applied driving waveforms.

• Journal of the Korean Applied Science and Technology
• /
• v.19 no.3
• /
• pp.174-180
• /
• 2002

In recent days, the study of a new phosphorescent phosphor has been performed in order to overcome the defect of sulfide phosphor and increase the brightness and long after-glow characteristic of phosphorescent phosphor. Particularly, sulfide phosphor usually used is so chemically unstable that the study of oxide phosphors are processing. $Eu^{2+}$, $Nd^{3+}$ doped Ba-Al-O phosphors sintered at $600{\sim}1500^{\circ}C$ for 2hours had the PL emission spectrum and after-glow over $1200^{\circ}C$. In this system, as the mole concentration of alumina increases, emission bands of phosphors moved from 500nm to 380nm. The optimum concentration of flux was 5wt% and after-glow characteristics of phosphors were found at the host material molar ratio ($BaCO_{3}:Al_{2}O_{3}$), 1:1 and 1:3.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.06a
• /
• pp.271-284
• /
• 1999

As a semiconductor material for electronic devices operated under extreme environmental conditions, silicon carbides (SiCs) have been intensively studied because of their excellent electrical, thermal and other physical properties. The growth characteristics of single-crystalline 4H-SiC homoepitaxial layers grown by a thermal chemical vapor deposition (CVD) were investigated. Especially, the successful growth condition of 4H-SiC homoepitaxial layers using a SiC-uncoated graphite susceptor that utilized Mo-plates was obtained. The CVD growth was performed in an RF-induction heated atmospheric pressure chamber and carried out using off-oriented substrates prepared by a modified Lely method. In order to investigate the crystallinity of grown epilayers, Nomarski optical microscopy, Raman spectroscopy, photoluminescence(PL), scanning electron microscopy (SEM) and other techniques were utilized. The best quality of 4H-SiC homoepitaxial layers was observed in conditions of growth temperature 1500$^{\circ}C$ and C/Si flow ratio 2.0 of C3H3 0.2sccm & SiH4 0.3sccm. The growth rate of epilayers was about 1.0$\mu\textrm{m}$/h in the above growth condition.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.315-319
• /
• 2003

The quality, quantity, color, and characteristics were found out cultured seawater pearls and freshwater pearls. In the XRF measurement Ca chemical combinations were the main elements and Sr was detected at higher levels for the sea-water pearl and Si, S, Ca, Mn, P and other elements were found at higher levels for the fresh-water pearls. Such differences is judged to be caused by the ion diluted in sea and fresh water which affects the pearl elements. Although near similar structural peak was shown for the FT-IR measurement, the fresh-water pearl showed a lower peak for the 2344 wave. For the results of PL, the peak for fresh-water measured with Hd-Cd Laser at 455 nm was higher and with the Ar-ion Laser measurements, peaks were high at 545 nm and 570 nm for fresh-water pearl and sea-water pearls respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04b
• /
• pp.57-60
• /
• 2002

In generally, the guest-emitter doped system has been reported to give a bright electroluminescence(EL). The purpose of using doped system is to improve for increasing lifetime and efficiency, and tuning multicolor light. This indicates an enhanced electron-hole recombination rate in emitting layer. The purpose of this study is to obtain the high performance EL devices for flat panel display with red emission. We fabricated EL devices using the guest-host system. where DCM derivatives were taken as a dopant. The devices are fabricated in multilayer system with various concentration of the dopant (red light emitting dye). We measured the I-V characteristics and EL spectra from these devices. and we compared with photoluminescence(PL) quantum yield among the DCM derivatives. The emission mechanism of devices is participated in energy transfer. The energy transfer from these hosts to DCM generates luminescence spectra that vary from yellow red to red, depending on DCM derivatives. Absorption and emission spectra of organic materials composing the devices depend on the emission materials doped with the DCM derivatives. We demonstrated that the high EL efficiency can be achieved by doping host material with DCM derivatives and molecular steric structures