• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.387-388
• /
• 2013

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.221-221
• /
• 2012

Small-molecule organic photovoltaic cells have recently attracted growing attention due to their potential for the low-cost fabrication of flexible and lightweight solar modules. The PVP/Ag nanoparticles were synthesized by the reaction of poly vinylpyrrolidone (PVP) and silver nitrate at $150^{\circ}C$. In the reaction, the size of the nanoparticles was controlled by relative mole fractions between PVP and Ag. The PVP/Ag nanoparticles with various sizes were then spin coated on the patterned ITO glass prior to the deposition of the PEDOT:PSS hole transport layer. The scattering of the incident light caused by these incorporated nanoparticles resulted in an increase in the path length of the light through the active layer and hence the enhancement of the light absorption. This scattering effect increased as the size of the nanoparticles increased, but it was offset by the decrease in total transmittance caused by the non-transparent nanoparticles. As a result, the maximum power conversion efficiency, 0.96% which was the value enhanced by 14% compared to the cell without incorporation of nanoparticles, was obtained when the mole fraction of PVP:Ag was 24:1 and the size of the nanoparticles was 20~40 nm.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.146-146
• /
• 2015

We report the enhanced performance of poly(N-vinylcarbozole) (PVK)/poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS)-based quantum-dot light-emitting diodes by inserting the polyaniline:poly (p-styrenesulfonic acid) (PANI:PSS) interlayer. The QD-LED with PANI:PSS interlayer exhibited a higher luminance and luminous current efficiency than that without PANI:PSS. Ultraviolet photoelectron spectroscopy results exhibited different electronic energy alignments of QD-LEDs with/without the PANI:PSS interlayer. By inserting the PANI:PSS interlayer, the hole-injection barrier at the QD layer/PVK interface was reduced from 1.45 to 1.23 eV via the energy level down-shift of the PVK layer. The reduced barrier height alleviated the interface carrier charging responsible for the deterioration of the current and luminance efficiency. This suggests that the insertion of PANI:PSS interlayer in QD-LEDs contributed to (i) increase the p-type conductivity and (ii) reduce the hole barrier height of QDs/PVK, which are critical factors leading to improve the efficiency of QD-LEDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.65-68
• /
• 2003

Recently, there is a growing concern on the photovoltaic effects using organic materials. This is a phenomena which converts the solar energy into the electrical one. We have fabricated a device structure of ITO/PEDOT:PSS/CuPc/$C_{60}$/BCP/Al. The PEDOT:PSS layer is made by spin coating. and the other organic layers are made by thermal vapor deposition. By measuring the current-voltage characteristics with an illumination of light. we have obtained a value of $V_{oc}$=0.358V and $J_{sc}$=0.338mA/$cm^2$. A fill factor and efficiency are about 0.271 and 0.033%, respectively. A 500W xenon lamp(ORIEL) was used for a light source, and the light intensity illuminated into the device was about 10mW.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.445-445
• /
• 2013

유기태양전지는 간단한 제조공정, 낮은 제조단가, 가벼운 무게 및 우수한 유연성의 장점을 가지고 있기 때문에 모바일 기기의 응용에 많은 관심을 가지고 있다. 그러나 이종접합 유기태양전지의 광전 변환효율이 낮기 때문에 유기태양전지를 상용화하기 위해서는 광전변환 효율을 높이기 위한 연구가 필요하다. 본 연구에서는 태양전지의 광전 변환효율을 증진하기 위하여 열처리 시간 변화에 따른 이종접합 유기 태양전지의 특성에 미치는 효과를 조사하였다. 전자 주게 물질인 P3HT와 전자 받게 물질인 PCBM 물질을 특정용매에 녹여 패턴화된 ITO를 코팅한 glass 기판 위에 스핀 코팅 방법을 이용하여 glass/ITO/PEDOT:PSS/P3HT:PCBM/Al 구조를 가진 이종접합 유기태양전지를 제작하였다. UV-Vis 분광학, X-선 광전자 분광학 및 원자힘 현미경 측정을 하여 제작한 소자의 광학적 및 구조적 특성을 분석하였다. 이종접합 유기태양전지의 우수한 광흡수율과 평탄한 표면을 가지는 최적화 조건을 열처리 시간에 따라 비교 분석하였다. 제작한 소자들을 열처리를 하지 않은 소자와 다양한 시간 동안 열처리를 한 소자의 특성을 비교하였다. 제작한 이종접합 태양전지의 전류-전압 측정 결과를 분석하여 최대의 광전 변환효율을 가지는 최적의 열처리 조건을 결정하였다. 열처리를 할 경우 열처리를 하지 않은 소자보다 광전 변환효율이 증가함을 알 수 있었다.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.2
• /
• pp.124-129
• /
• 2011

A simple process of fabricating micropillar structure and its influence upon enhancing electrochemical biosensor response were studied in this work. Conducting polymer PEDOT was used as a base material in formulating a composite with PVA. Micro porous PC membrane filter was used as a template for the micropillar of the composite on ITO electrode. This structure could provide plenty of encapsulating space for enzyme species. After dosing enzyme solution into this space, Nafion film tent was cast over the pillar structure to complete the micropillar cavity structure. In this way, the encapsulation of enzyme could be accomplished without any chemical modification. The amount of enzyme species was easily controllable by varying the concentration of the dosing solution. The more amount of enzyme is stored in the sensor, the higher the electrochemical response is produced. One more reason for the sensitivity improvement comes from the large surface area of the micropillar structure. Application of 0.7 V produced the best current response under the condition of pH 7.4. This biosensor showed linear response to the glucose in 0.1~1 mM range with the average sensitivity of $14.06{\mu}A/mMcm^2$. Detection limit was 0.01 mM based on S/N = 3.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.123-126
• /
• 2003

Recently, there is a growing concern on the photovoltaic effects using organic materials. This is a phenomena which converts the solar energy into the electrical one. We have fabricated a device structure of $ITO/PEDOT:PSS/CuPc/C_{60}/BCP/AI$. The PEDOT:PSS layer is made by spin coating, and the other organic layers are made by thermal vapor deposition. By measuring the current-voltage characteristics with an illumination of light, we have obtained value of Voc=0.38V, Jsc=$0.5mA/cm^{2}$. And a fill factor and efficiency are about 0.314 and 0.083%, respectively. A 500W xenon lamp(ORIEL) is used for a light source, and the light intensity illuminated into the device was about 10mW.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1277-1278
• /
• 2008

Pentacene 박막 트랜지스터의 소스/드레인 전극을 폴리머인 Poly(3,4-ethylene dioxythiophene) poly(styrenesulfonate) (PEDOT:PSS)를 사용하여 잉크젯 프린팅 방법으로 제작하였다. 펜타신 박막 트랜지스터는 열 증착법을 사용하여 폴리며 기판위에 100nm의 두께로 증착하였다. 게이트 절연막은 $SiO_2$ 위에 Polymethly Methacrylate (PMMA)를 증착시킨 double layer를 사용하였다. PMMA 위에 증착시킨 pentacene 결정립이 $SiO_2$ 위에 증착한 pentacene 결정립 보다 크게 성장하였고, double layer의 절연막을 씀으로 인해 게이트 누설 전류가 감소함을 보였다. Pentacene 증착 온도에 따른 결정립 크기를 비교하여 가장 적절한 온도를 찾았다. 프린팅 방법을 사용하여 만든 박막 트랜지스터는 전계효과 이동도가 ${\mu}_{FET}=0.023cm^2/Vs$ 이고, 문턱이전 기울기 S.S=0.49V/dec, 문턱전압 $V_{th}=-18V$, $I_{on}/I_{off}$ 전류비 >$10^3$의 전기적 특성을 보였다.

• Proceedings of the KAIS Fall Conference
• /
• 2008.11a
• /
• pp.201-203
• /
• 2008

ITO 투명전극을 양극으로 사용하고 PEDOT:PSS 고분자 물질위에 PVK와 Ir(ppy)3를 각각 host와 dopant로 사용하여 고분자 발광다이오드를 제작하였다. 전자 수송층의 역할로 TPBI, 음극으로 Al을 증착하여 최종적으로 ITO/PEDOT:PSS/PVK:Ir(ppy)3/TPBI/LiF/Al 구조를 갖는 녹색 인광 고분자 유기발광소자(PhPLED)를 제작하였다. 제작 된 소자의 발광부 dopant인 Ir(ppy)3도핑 농도에 따른 전기적 광학적 특성을 평가하였다. PVK:Ir(ppy)3를 host와 dopant system으로 dopant Ir(ppy)3의 도핑 양을 0.5 wt%에서2.5 wt%까지 씩 변화시키면서 최적의 농도를 찾고자 하였다. TPBI를 전자 수송층으로 사용 하였을 경우 최대 휘도는 약 8600 cd/$m^2$ (at 8V)이고, 전류밀도는 337mA/$cm^2$ 를 나타내었다.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.1
• /
• pp.73-78
• /
• 2020

There appears lateral capillary force in a hydrophilic flat needle employed for the fabrication of fine organic thin-film stripes, bringing in an increase of the stripe width. It also causes the stripe thickness to increase with increasing coating speed, which is hardly observed in a normal coating process. Through computational fluid dynamics (CFD) simulations, we demonstrate that the lateral capillary flow can be substantially suppressed by increasing the contact angle of the needle end. Based on the simulation results, we have coated the outer surface of the flat needle with a hydrophobic material (polytetrafluoroethylene (PTFE) with the water contact angle of 104°). Using such a hydrophobic needle, we can suppress the lateral capillary flow of an aqueous poly(3,4-ethylenedioxythiophene): poly(4-styrenesulfonate) (PEDOT:PSS) to a great extent, rendering the stripe narrow (63 ㎛ at 30 mm/s). Consequently, the stripe thickness is decreased as the coating speed increases. To demonstrate its applicability to solution-processable organic light-emitting diodes (OLEDs), we have also fabricated OLED with the fine PEDOT: PSS stripe and observed the strong light-emitting stripe with the width of about 68 ㎛.