• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.120-124
• /
• 1994

PBH-DFB-LD emitting at $1.55\mu\textrm{m}$ wavelength has been fabricated for 2.5 Gbps optical fiber communications. For fabrication of PBH-DFB-LD. inteference expose for grating formation and 3-step LPE epitaxial growth was used. Fabricated PBH-DFB-LD operates in single longitudinal mode with more than 35dB SMSR and its threshold current is less than 15 mA. The operating wavelength is 1530-1550 nm with the temperature dependence of $0.9\AA/^{\circ}C$. Coupling coefficient(K) was estimated as $$97 cm^{-1} by means of stop-band measurement. PBH-DFB-LD fabricated in this experiment can be applicable as light source for 2.5 Gbps optical fiber communication system. ystem.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.481-485
• /
• 2002

In this study, we fabricated the PBH-LD by meltback method using the LPE. The PBH-LDs are analyzed the leakage current that flows through leakage current path like the p-n diode and p-n-p-n current blocking layer. We observed the variation of threshold current with the leakage width $W_{ι}$. As a consequence, we confirmed that the threshold current became low in the decrease of the leakage width and in the increase of the ratio of specific resistivity of leakage region to active region. We also compared between the calculated threshold current in the absence of leakage region and the measured threshold current in the device. As a result, the ratio of specific resistivity was about 0.5 in the measured LDs, which have the width of a active layer of 1.4${\mu}{\textrm}{m}$ and leakage width of 0.6${\mu}{\textrm}{m}$.

• Korean Journal of Optics and Photonics
• /
• v.6 no.3
• /
• pp.228-232
• /
• 1995

We have made modulation doped SMQW-PBH-DFB-LD for high speed optical communications. The waveguide and barrier layers were doped by Zn with the concentration of $1.2 \times 10^{18}cm^{-1}$. Mean threshold current and slope efficiency were 24.88 mA (minimum 16 mA) and 0.197 mW/mA (maximum 0.275 mW/mA) respectively. Linewidth enhancement factor ($\alpha$) of MD-SMQW-PBH-DFB-LD was reduced than that of SMQW-PBH-DFB-LD. Linewidth enhancement factor of 1.8 owes to the large gain coefficient of modulation doped active layer. The resonance frequency was linearly increased with the square root of optical power. The resonance frequency in small signal modulation was measured as 8 GHz and -3 dB modulation bandwidth was 10 GHzat $46mA(I_{th}+30mA)$..

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.9
• /
• pp.139-145
• /
• 1994

InGaAsP/InP PBH-DFB-LD emitting at 1.55${\mu}$m wavelength has been fabricated for 2.5Gbps optical fiber communcations. For fabrication of PBH-DFB-LD, Interference expose for grating formation 3-step LPE epitaxial growth were used. Fabricated PBH-DFB-LD operates in single longitudinal mode with larger than 35dB SMSR and wider than 3dB bandwidth of 3GHz. A 8${\mu}$m mesa structure was introduced by channel etching to reuce parasitic capacitance. To reduce pad capacitance, we designed a small electrode. 0.27mW/mA in the case of spectrum shows single logitudinal mode operation with larger thatn 30dB SMSR measured at 5mW.

• Korean Journal of Optics and Photonics
• /
• v.5 no.3
• /
• pp.418-422
• /
• 1994

본 연구에서는 MOVPE를 이용한 MQW활성층을 DFB-LD 구조에 도입함으로서 2.5Gbps 광전송용 광원으로 사용된 $ 1.55.\mu$m 파장의 MQW-PBH-DFB-LD를 제작하였다. 활성층으로는 MOVPE를 이용하여 8쌍의 InGaAs/InGaAsP MQW층을 성장하였으며 2차 및 3차 결정성장은 LPE를 사용하였고 발진파장을 결정하는 회절격자 주기는 238nm로 하였다. MQW-PBH-DFB-LD의 평균 임계전류는 13.81mA, Slope efficiency는 0.137mW/mA이었고 발진파장은 1548.6nm의 특성을 얻었다. 그리고 2.5Gbps 대신호 변조시의 chirping특성을 조사하여 본 결과 0.55nm임을 확인할 수가 있었다.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.185-197
• /
• 1996

We have adopted the strain compensated PBH(planar buried heterostructure) - LD in which the MQW active layer consisted of 1.4% compressively strained GainAsP (E$_{g}$ = 0.905eV) wells and 0.7% tensile strained GaInAsP(E$_{g}$ = 1.107eV) barriers grown by metal organic vapor phase epitaxy (MOVPE). We hav einvestigated effects of number of wells and the structure of the separate confinement heterostructure (SCH) layer in the strain-compensated MQW-PBH-LD. The threshold current, the external quantum efficiency, the transparency current density J$_{o}$, and the gain constant .beta. have been evaluated for uncoated MQW-PBH-LD. As the number of wells increases, the internal quantum efficiency and the transparency current density decreases, whereas the gain contant increases. The small width of the SCH layer shows the large internal quantum efficiency. The small internal loss and the large gain constant have been obtained by inserting the large bandgap SCH layer.

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.518-523
• /
• 1999

In thi, study, we made experiments to fonn a mesa shape by meltback method with various concentration of solutions and found that unsaturated (20%) InGaAsP (1.55 !-tm) solution at a growth temperature was the most suitable for the formation of a mesa ,hape on the wafer which has an InGaAsP active layer and an InP cap layer on an n-InP substrate. It was difficult to form a proper mesa shape for the fabrication of PBH-LDs only by the meltback method; therefore, we fabricated PBH-LDs by forming the mesa shape with the meltback method after wet etching and by growing a current-blocking layer successively. As the electrical and optical charaleri,tiecs of MQW-PBH-LDs fabricated by above methods, when the cavity length was $300{\mu}m$, the threshold current was about 10 mA, internal quantum efficiency 82%, internal loss $9.2cm^{-1}$, and characteristic temperature was 65 K at $25~45^{\circ}C$ and 42 K at $45~65^{\circ}C$. /TEX>.

• Korean Journal of Optics and Photonics
• /
• v.8 no.4
• /
• pp.327-332
• /
• 1997

We fabricated the high speed 1.55${\mu}{\textrm}{m}$ distributed feedback laser diodes (DFB-LD) using both two-step mesa etching process and semi-insulating InP current blocking layers. The devices characteristics were threshold current of ~15mA, slope efficiency of ~0.13mW/mA, and dynamic resistance of ~6.0Ω, with as-cleaved facets. The fabricated DFB-LD showed the single longitudinal mode with more than 40dB up to 6 $I_{th}$(CW condition), emitting at the wavelength of 0.546${\mu}{\textrm}{m}$. The -3dB bandwidth was >10㎓ at the driving current of 27mA, and the maximum -3dB bandwidth was ~18㎓ at 90 mA current, showing the superior frequency response of SI-PBH DFB-LD. In the 10Gb/s transmission experiment for 1.55${\mu}{\textrm}{m}$ DFB-LD module, maximum 10 km of single mode fiber(SMF) or 80 km of dispersion shifted fiber (DSF) could be transmitted with error free.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.16-20
• /
• 2004

We present the fabrication and performance of wavelength tunable butt coupled (BT) sampled-grating (SG) distributed bragg reflector (DBR) - planar buried heterostructure (PBH) laser diodes (LD). The fabricated LD showed the high optical output power due to the high coupling efficiency between active and passive components by the BT coupling methods. The series resistance and diode ideality factor of LD were measured to be 3.7 $\Omega$ and 1.35, respectively. The average threshold current was 25 ㎃. The output powers of BT-SG DBR-PBH-LD were obtained to be as high as 12.3 and 24.56 ㎽ at 100 and 200 ㎃, respectively. The maximum wavelength tuning range was about 31 nm and the side mode suppression ratio was about 37 dB.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.666-672
• /
• 2003

In this paper, we described the fabrication and the performance of wavelength tunable distributed bragg reflector (DBR) laser diode (LD), having different waveguide coupling mechanisms; integrated-twin-guide (ITG) DBR-LD and butt coupled (BT) DBR-LD. This deviceis fabricated by metal organic vapor phase epitaxy (MOVPE) growth and planar buried heterostructure (PBH)-type transverse current confinement structure. The result of measurement, the optical performance of BT-DBR-LD is better over 2 times than that of ITG-DBR-LD at the variation of threshold current and output power, and slop efficiency due to the higher coupling efficiency of the butt coupled structure than the integrated twin guide structure. The maximum wavelength tuning range is about 7.2nm for ITG DBR-LD and 7.4nm for BT DBR-LD. Both types of lasers have a very high yield of single mode operation with a side-mode suppression ratio of more than 35dB.