• Geomechanics and Engineering
• /
• v.22 no.3
• /
• pp.207-217
• /
• 2020

Slope reliability analysis and risk assessment for spatially variable soils under rainfall infiltration are important subjects but they have not been well addressed. This lack of study may in part be due to the multiple and diverse evaluation indexes and the low computational efficiency of Monte-Carlo simulations. To remedy this, this paper proposes a highly efficient computational method for investigating random field problems for slopes. First, the probability density evolution method (PDEM) is introduced. This method has high computational efficiency and does not need the tens of thousands of numerical simulation samples required by other methods. Second, the influence of rainfall on slope reliability is investigated, where the reliability is calculated from based on the safety factor curves during the rainfall. Finally, the uncertainty of the sliding mass for the slope random field problem is analyzed. Slope failure consequences are considered to be directly correlated with the sliding mass. Calculations showed that the mass that slides is smaller than the potential sliding mass (shallow surface sliding in rainfall). Sliding mass-based risk assessment is both needed and feasible for engineered slope design. The efficient PDEM is recommended for problems requiring lengthy calculations such as random field problems coupled with rainfall infiltration.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.535-542
• /
• 2000

The investigated cut-slope is located in Odong-Ri, Hoebuk-Myun, Boeun-Gun and composed of quartzite and phyllitic rocks (approximately 80 meters in length and 25 meters in height). During the investigation, the groundwater which was inferred to the natural pipe of slope was continuously flowing in the upper part of slope. The investigation for discontinuity properties in this area was carried out to decide the rock mass rating and strength parameters. To analyze the stability of cut-slope, lower equal-area hemisphere projection method was used. And laboratory test was done to evaluate engineering properties of soil which was sampled in the non-failure and failure area The inferred causes of cut-slope failure are the geometric relationship between the orientation of cut-slope and geological structures such as joints, faults which is distributed in the slope. And direct cause of failure is the increase of water content due to the heavy rainfall.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.176-183
• /
• 2008

This paper highlights the importance of carrying out global slope stability analysis as part of design calculations for geosynethetic walls in tiered configuration. Four design case histories were selected to examine the appropriateness of their design by performing additional slope stability analyses using the shear strength reduction method with in the frame work of finite element analysis. The results indicated that all of the walls examined, which were designed to meet the current design guide lines, did not satisfy the global slope stability requirement, and that longer reinforcements are required in the upper tiers to achieve the minimum factor of safety. Practical implications of the findings are discussed.

• Proceedings of the KSEG Conference
• /
• 2002.04a
• /
• pp.109-114
• /
• 2002

Development of a three-dimensional mine visualization model for a section of the mine is addressed first. Discontinuity orientation and location information was taken from this visualization model for use in slope stability analyses. Estimated shear strength properties of discontinuities and mechanical properties of intact rock from the rock mass samples obtained from the mine are discussed next. The third part of the paper is focused on the results obtained for maximum safe slope angles for the section considered of the mine based on block theory analysis conducted under only the gravitational forces using the mapped discontinuities at the mine. Finally, the effects of water that exist in the rock mass, a tension crack, slope face inclination, overall wedge height and double benching on factor of safety of wedge stability are illustrated through limit equilibrium slope stability analyses conducted on a single tetrahedral wedge belonging to potential key block category that exist in the investigated area of the mine.

• Korean Journal of Agricultural Science
• /
• v.35 no.2
• /
• pp.213-223
• /
• 2008

The instability of rock slopes caused by heavy rainfall and soil mass sliding needs the preventable and reinforcing method. The most important factor for the stability is the shear strength available in the planar part of the failure surface, which shows that a progressive failure takes place and a reinforcing of rock slope using FRP grout is effectively available. In this study, a grouting bolting interval predictions by limit equilibrium analysis and Matlab mathematical computer codes in several cases is presented for FRP reinforced rock slope. The proposed mathematical computer code can be easily applied for seeking properly FRP grout intervals prior to design and execute a reinforcement of a rock slope in practice.

• Journal of Welding and Joining
• /
• v.34 no.6
• /
• pp.62-68
• /
• 2016

Laser welding has superior characteristic such as low distortion, high welding speed, easy automation and real time control. But it is easy to occur weld defects such as porosity, crater, humping bead in the area of welding start and end. These weld defects can be suppressed by applying the wave shape control. In this study CW fiber laser was used for welding of $0.5mm^t$ pure titanium. Penetration properties were evaluated with the time of slope up and down. After then the bead shape was observed, and the maximum depth and the area of crater were measured. The bead shape of welding start area changed to be sharp with increase of slope up time and non-weld area of welding start increased. The crater and humping bead were suppressed with slope down time. The cooling rate of crater area was understood through measure of the hardness. Also, The distribution tendency of alloying elements was observed by EPMA and EDS. When wave shape control didn't applied to weld, the hardness of end weld increased due to rapid cooling rate and the hardness of rear part in the crater was higher than that of fore part. On the other hand, when the wave shape control was used for end weld, the increase of hardness in the end weld couldn't be found due to gradual cooling rate.

• Geomechanics and Engineering
• /
• v.31 no.5
• /
• pp.439-452
• /
• 2022

A forecast of slope behavior during catastrophic events, such as earthquakes is crucial to recognize the risk of slope failure. This paper endeavors to eliminate the significant supposition of predefined slip surfaces in the slope stability analysis, which questions the relevance of simple conventional methods under seismic conditions. To overcome such limitations, a methodology dependent on the slip line hypothesis, which permits an automatic generation of slip surfaces, is embraced to trace the extreme slope face under static and seismic conditions. The effect of earthquakes is considered using the pseudo-static approach. The current outcomes developed from a parametric study endorse a non-linear slope surface as the extreme profile, which is in accordance with the geomorphological aspect of slopes. The proposed methodology is compared with the finite element limit analysis to ensure credibility. Through the design charts obtained from the current investigation, the stability of slopes can be assessed under seismic conditions. It can be observed that the extreme slope profile demands a flat configuration to endure the condition of the limiting equilibrium at a higher level of seismicity. However, a concurrent enhancement in the shear strength of the slope medium suppresses this tendency by offering greater resistance to the seismic inertial forces induced in the medium. Unlike the traditional linear slopes, the extreme slope profiles mostly exhibit a steeper layout over a significant part of the slope height, thus ensuring a more optimized solution to the slope stability problem. Further, the susceptibility of the Longnan slope failure in the Huining-Wudu seismic belt is predicted using the current plasticity approach, which is found to be in close agreement with a case study reported in the literature. Finally, the concept of equivalent single or multi-tiered planar slopes is explored through an example problem, which exhibits the appropriateness of the proposed non-linear slope geometry under actual field conditions.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.5 no.3
• /
• pp.15-22
• /
• 2002

To analysis of the embanked slope stability using a jointed reinforcement, the internal stability and the external stability have to be satisfied, respectively. But, because the lengths of ready-made steel-grid were limited, the reinforcements must be connecting themselves to the reinforcing. In this study, the mechanical test was carried out to investigate the tensile failure and the pullout failure at the joint parts of them, which was based on the analysis of reinforced slope in field. Through the tensile tests in mid-air for the jointed steel-grid, the deformation behavior was seriously observed as follows : deformation of longitudinal member, plastic deformation of longitudinal member and of crank part. Those effects were due to the confining pressure and overburden pressure of the surrounding ground. The bearing resistance at jointed part of jointed steel-grid was due to the latter only. The maximum tensile forces were higher about 20kN~27kN than ultimate pullout resistance, but, the results of those was almost the same in mid-soil. The failures of steel-grid occurred at welded point both of longitudinal members and transverse members and of jointed parts. The strength of jointed parts itself got pullout force about 20kN, which was about 65% for ultimate pullout force of the longitudinal members N=2. To the stability analysis of reinforced structure including the reinforced slope, the studying of connection effects at jointed part of reinforcement members must be considered. Through the results of them, the stability of reinforced structures should be satisfied.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.1 no.1
• /
• pp.63-69
• /
• 1998

The slope revegetation methods in Korea are generally the hydroseeding mixed with perennial herbs, soil, fibers, and fertilizer in consideration of scenic landscape rather than ecological and engineering effect. But perennial herbs can't protect the slope from deep surface erosion and they are not tall enough to create the original naturalness at the boundary parts of existing woodlands. This study is about the slope revegetation method using nutritional propagation capacity of plants and the experimental construction was carried out on the cut-slope of Yongin Hoam C.C. We dug several trenches to a depth of 80cm and at intervals of 150cm from each other. After placing various kinds of live branches(Salix species) into the trench, we backfilled with the excavated soils and finally sprayed water mixed with soil-stabilizer, fertilizer. As six months passed, we made a vegetation research and check the slope surface erosion. Vegetation research was performed in examining the frequency of each block using transect method. 31 kinds of plant species appeared in total area($113.6m^2$) and the dominant species are Setaria viridis, Artemisia rubripes, Persicaria pubescens, Plantago asiatica, Cyperus amuricus, Commelina communis. Among the examined blocks, '아', the top part of the slope, showed the ratio of 1.4 as the highest Alpha-diversity. With regard to life form, therophytes were shown dominant distribution of 58% of total species and neophytes relatively low distribution of 16%. It can be estimated that there is no ecological stabilization of this slope, because of ruderal species' occupation of 74% in total area. Regarding the slope stabilization, the serious surface erosion didn't take place in spite of heavy rainfall this year, but a little surface erosion took place at the block where no other species coming from outside of the site were found.

• Proceedings of the Korean Society of Environment and Ecology Conference
• /
• 2004.04a
• /
• pp.174-176
• /
• 2004