• Journal of the Korean institute of surface engineering
• /
• v.32 no.6
• /
• pp.671-676
• /
• 1999

ITO (indium tin oxide) thin films on PET (polyethylene terephthalate) substrate have been deposited by a dc reactive magnetron sputtering without heat treatments such as substrate heater and post heat treatment. Each sputtering parameter during the sputtering deposition is an important factor for the high quality of ITO thin films deposited on polymeric substrate. Particularly, the material, electrical and optical properties of as-deposited ITO oxide films are dominated by the ratio of oxygen partial pressure. As the experimental results, the excellent ITO films are prepared on PET substrate at the operating conditions as follows : operating pressure of 5 mTorr, target-substrate distance of 45mm, do power of 20~30W, and oxygen gas ratio of 10%. The optical transmittance is above 80% at 550 nm, and the sheet resistance and resistivity of films are 24 Ω/square and $1.5\times$10$^{-3}$ Ωcm, respectively.

• Journal of the Korean Chemical Society
• /
• v.11 no.1
• /
• pp.28-32
• /
• 1967

The direct acid leaching of domestic Marmatite concentrate at elevated temperatures and pressures was investigated. Almost 100 percent of zinc was extracted from the concentrate liberating free sulfur in 4 hours at $100^{\circ}C$ when the oxygen partial pressure was 5 atm. in sulfuric acid solution. By applying the Arrhenius equation to leach reaction in the range of $60^{circ}$ to $100^{\circ}C$ at the same oxygen partial pressure, 15.7 kcal per mole of activation energy was calculated. At the initial stage of leaching, the rate of reaction increased linearly by increasing temperature and pressure. The concentration of sulfuric acid gave minor effect to leaching velocity in the range of 5 to 20 percent. The particle size should be under 270 mesh for 100 percent extraction of zinc.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.355-356
• /
• 2006

WC-TiC-TaC binderless cemented carbide was oxidized under low partial pressure of oxygen (50ppm) at 873K for 1 to 20 h. Surface roughness was measured using atomic force microscope, and effect of TiC amount on oxidation behavior of the carbide was investigated. WC phase was oxidized more easily than WC-TiC-TaC solid solution phase. With an increase in TiC amount, WC-TiC-TaC phase increased and the oxidation resistance of the carbide increased.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05a
• /
• pp.6-8
• /
• 2004

The NdBaCuO superconductor samples were zone-melted in low oxygen partial pressure (1 % $O_2$＋99%Ar). The zone-melting temperature was decreased about 12$0^{\circ}C$ from 1, 06$0^{\circ}C$, the zone-melting temperature in air. Thus the loss of liquid phase (BaCu $O_2$and CuO) was reduced during the zone-melting process. The content of non-superconducting phase Nd422 in zone-melted NdBaCuO samples was clearly decreased and, therefore, the substitution of Nd for Ba was occurred. The superconductivity of zone-melted N $d_{1＋x}$B $a_{2－x}$C $u_3$ $O_{y}$prepared under low oxygen partial pressure was distinctively improved.d.d.d.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.353-353
• /
• 2014

본 연구에서는 Sputter를 이용하여 Room Temp.에서 증착된 NbOx 박막의 열처리에 따른 결정도를 분석하고, 이러한 결정도의 변화가 Metal Insulator Transition특성에 의한 Threshold switching에 어떠한 영향을 미치는 지에 대하여 연구하였다. NbOx 박막의 threshold switching 특성 분석을 위해, 1.4um의 TiN 위에 15nm의 NbOx를 증착하고 Top Electrode로 Pt를 증착하여 측정하였다. 증착된 NbOx는 Nb metal target으로 Reactive Sputter를 이용하여 Room Temp.에서 증착하였으며, 조성은 Partial Oxygen Pressure를 이용하여 조절하였다. 증착된 박막의 결정도는 TEM 및 XRD를 통하여 분석하였고 조성은 XPS를 이용하여 분석하였다. Sputter로 NbOx 증착 시 Partial Oxygen Pressure에 따른 조성을 XPS로 확인한 결과, Partial Oxygen Pressure 2%에서 NbOx의 조성을, 5%이상일 경우, Nb2O5의 조성을 가지는 것으로 확인되었다. Partial Oxygen Pressure 2%에서 증착한 NbOx 박막의 열처리에 따른 결정도를 분석한 결과, As-Dep상태에서는 amorphous상태였다가 600'C이상으로 1분간 열처리를 하였을 때 NbOx의 결정도가 증가함을 확인하였다. I-V 특성 측정 결과, 열처리 온도가 증가함에 따라 initial current가 점진적으로 증가하는 경향을 보이는데, 이는 열처리 시 amorphous상에서 poly-crystalline으로 미세구조의 변화가 일어나면서 grain boundary가 생성되며 생성된 grain boundary를 통해 leakage current가 증가하는 것으로 추측된다. 또한, 결정도가 증가함에 따라 electro-forming voltage가 감소하는 경향을 보이며 안정된 threshold switching 특성을 보이고 있다. 특히, 700'C 1분간 열처리 시에는 electro-forming 과정이 없이 threshold switching이 나타나는 현상이 관찰되었다. 이로 미루어 보아, threshold switching에서 나타나는 forming 현상은 local joule heating에 의해 박막이 결정화 되는 과정으로 추측된다. 결론적으로, 박막의 결정도가 initial current 및 Threshold switching 특성에 큰 영향을 미치는 것으로 예상된다.

• Tuberculosis and Respiratory Diseases
• /
• v.51 no.1
• /
• pp.44-52
• /
• 2001

Background : Oxygen concentrators are convenient to operate and economical for patients with chronic obstructive pulmonary disease (COPD). However, oxygen concentrators are not manufactured domestically and the COPD patients are currently treated with imported oxygen concentrators. To evaluate the efficacy and safety of domestically developed prototype oxygen concentrator before clinical application, the efficacy and safety of the domestic oxygen concentrator were evaluate by comparing with the imported one. Material and Methods : The clinical tests were performed on 36 hyperhydrosis patients from April 1999 to August 1999. Domestic and imported oxygen concentrators were in turn applied to the same patient, who inspired oxygen for 60 minutes at a rate of 3 liters per minute through nasal prong. The oxygen concentrator, which was applied first, was randomly allocated. The arterial partial oxygen pressure ($PaO_2$) was estimated to compare the efficacy; and the carboxy hemoglobin(COHb), pH, arterial $CO_2$ partial pressure, pulse rate, blood pressure, and respiration rate to compare the safety before and after applying each oxygen concentrator. A student t-test was used to analyze the results. Result : In respect to efficacy, the difference in the change of $PaO_2$ before and after the application between two concentrators was not statistically significant. In respect to safety, the differences in the changes of COHb, pH, partial pressure of arterial $CO_2$, pulse rate, blood pressure, respiration rate between two concentrators were also not statistically significant. Conclusion : The domestically developed oxygen concentrator, showed satisfactory efficacy and safety when compared with the imported one.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.122-123
• /
• 2006

Tin oxide nanoparticles (n-SnO and $n-SnO_2$) were synthesized by the inert gas condensation (IGC) method under dynamic gas flow of oxygen and argon at various conditions. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) method were used to analysis the size, shape and crystal structure of the produced powders. The synthesized particles were mostly amorphous and their size increased with increasing the partial pressure of oxygen in the processing chamber. The particles also became broader in size when higher oxygen pressures were applied. Low temperature annealing at $320^{\circ}C$ in air resulted to crystallization of the amorphous n-SnO particles to $SnO_2$.

• Progress in Superconductivity
• /
• v.4 no.2
• /
• pp.176-179
• /
• 2003

A lot of efforts have been focused on the optimization of PIT parameters for Bi-2223/Ag wire. Bi-2223 superconducting wires with 55 filaments were fabricated by stacking, drawing process. Before rolling process, round wires were pre -annealed at 760 - 820 $^{\circ}C$ and low oxygen partial pressure. We confirmed that pre-annealing step was to transform Bi-2212 orthorhombic structure from Bi-2212 tetragonal structure and to reduce the formation of second phases. However Bi-2223 phases also were formed at higher than 76$0^{\circ}C$ of pre-annealing temperature. The engineering critical current densities (Je) of Bi-22231Ag tapes were sintered at low oxygen partial pressure were higher than t hat of the wires sintered at air. We could achieve 6500 A/${cm}^2$ of Je for the tape that was initially kept at slightly higher temperature than that of normal heat treatment.

• Korean Journal of Metals and Materials
• /
• v.47 no.2
• /
• pp.107-113
• /
• 2009

Molten iron with 2 mass % carbon content was decarbonized at 1823 K~1923 K by bubbling $Ar+O_2$ gas through a submerged nozzle. The reaction rate was significantly influenced by the oxygen partial pressure and the gas flow rate. Little evolution of CO gas was observed in the initial 5 seconds of the oxidation; however, this was followed by a period of high evolution rate of CO gas. The partial pressure of CO gas decreased with further progress of the decarbonization. The overall reaction is decomposed to two elementary reactions: the decarbonization and the dissolution rate of oxygen. The assumptions were made that these reactions are at equilibrium and that the reaction rates are controlled by mass transfer rates within and around the gas bubble. The time variations of carbon and oxygen contents in the melt and the CO partial pressure in the off-gas under various bubbling conditions were well explained by the mathematical model. Based on the present model, it was explained that the decarbonization rate of molten iron was controlled by gas-phase mass transfer at the first stage of reaction, but the rate controlling step was transferred to liquid-phase mass transfer from one third of reaction time.

• Applied Chemistry for Engineering
• /
• v.4 no.1
• /
• pp.153-161
• /
• 1993

Cathodic oxygen reduction kinetics on $La_{0.9}Sr_{0.1}MnO_3$ electrode have been examined at $700-900^{\circ}C$ under various oxygen partial pressures. AC impedance and current interruption techniques were employed for the determination of charge transfer resistances for electrochemical oxygen reduction. The $R_{ct}$ values obtained from two different methods were very close each other for $La_{0.9}Sr_{0.1}MnO_3$ electrode. Activation energy for the electrochemical oxygen reduction was found to be 174kJ/mol under atmospheric oxygen pressure. $R_{ct}$ measurements as a function of oxygen partial pressure indicate that the rate-determining step for the electrochemical oxygen reduction on $La_{0.9}Sr_{0.1}MnO_3$ electrode is the charge transfer process.