• Korean Journal of Metals and Materials
• /
• v.49 no.1
• /
• pp.17-24
• /
• 2011

To investigate the relationship between heat treatment in zirconium alloy tubing process and metallurgical characteristics of Zr-1Nb-0.69Sn-0.11Fe alloy tubes, mechanical and oxidation behaviors of tubes heat treated at different temperatures after the final pilgering were investigated. The stress strain curves exhibited the saturation behaviors in all heat treatment conditions ($460{\sim}600^{\circ}C$) in this study with the onset strain of saturation increased with increase of post-pilgering annealing temperature. The strength fell off rapidly with increasing annealing temperature. The ultimate strength of the low tin Zr-1Nb-0.69Sn-0.11Fe alloy with slightly higher iron and oxygen contents in this study was found to be higher than Zr-1Nb-1Sn-0.1Fe alloy. The oxidation experiments in steam condition revealed that the corrosion resistance of low tin Zr-1Nb-0.69Sn-0.11Fe alloy was better than the Zr-1Nb-1Sn-0.1Fe alloy with a higher Sn content. The weight gain of low tin Zr-1Nb-0.69Sn-0.11Fe alloy tubes gradually increased with the increasing annealing temperature possibly due to the decreased Nb content in the matrix because of the formation of ${\beta}-Nb$ particles.

• Journal of Plant Biology
• /
• v.31 no.3
• /
• pp.205-215
• /
• 1988

The effects of simetryne on light induced electron transport and phosphorylation in isolated spinach (Spinacia oleracea L.) chloroplasts were investigated in comparison with sencor and DCMU. Simetryne, like sencor and DCMU, completely, inhibited PSII electron transport and phosphoryltion with 10-6 M treatment but did not inhibit PSI electron transport. Interference with the electron transport pathway was evidenced by the greater sensitivity of oxygen evolution and uptake than phosphorylation. The following order of decreasing inhibitory effectiveness was exihibited; DCMU>simetryne>sencor. The photoacoustic technique was also used to monitor the relative photosynthetic activity in the leaves treated with the herbicides (simetryne, sencor or DCMU) in vivo and in vitro. Photoacoustic measurements on intact leaves provide quantitative information on two related aspects of the photosynthetic process, namely, photochemical energy storage and oxygen evolution. The relative photoacoustic signal of leaves treated with the herbicides showed low level in 21 Hz, but high level in 380 Hz and on isolated chloroplasts (both 21 Hz and 380 Hz) in comparison with that of the untreated leaves. These results suggest that some of photochemical energy is converted into the heat owing to the inhibition of electorn transport pathway by the herbicides.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.126-127
• /
• 2008

The effects annealing conditions on the electrical conductions of SOI substrate were studied. The reversible change of resistance and carrier concentration in accordance with the annealing temperature were observed for the first time in SOI substrate. The thermal donors due to interstitial oxygen atoms contribute the change of resistance and carrier concentration. Final1y, we show that the furnace annelaing at $500^{\circ}C$ at final heat treatment stage is effective for eliminate the thermal donor effects in SOI substrate.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.3
• /
• pp.76-82
• /
• 2000

It is well known that during the oxygen cutting process residual thermal stresses are produced in weldment. The local non-uniform heating and subsequent cooling which takes place during any welding process causes complex thermal strains and stresses to finally lead to residual stresses exceed to the yield stress. High tensile stresses combined with applied structural load in the region near the welded joint can given rise to distortion brittle fracture change of the fatigue strength and stress corrosion cracking. The appropriate treatment of the welded component which reduces the peak of he welding residual stresses is believed to lower risk of the fracture during the service of the structure. In this study the impact loading in oxygen cutting frame was applied to reduce the residual stress. After applying the impact loading redistribution of resid-ual stress was measured by cutting method and the effect of fatigue was tested.

• Journal of the Korean Magnetics Society
• /
• v.10 no.3
• /
• pp.123-132
• /
• 2000

Cerium substituted YIG thin films were grown by rf magnetron sputter techniques. We investigated the effects of post-deposition heat-treatment as well as various deposition parameters such as substrate materials, substrate temperature. sputter power, and sputter gas types on the crystallinity, chemical composition, microstructure and magnetic characteristics of the films. Post-deposition heat treatment over 750 $\^{C}$ was applied to crystallize as-prepared amorphous films, and a strong tendency of particular crystallographic planes tying parallel to substrate surface was observed for the post-deposition heat-treated films on GGG substrate. The chemical composition of the films exhibited a wide range of chemical stoichiometry depending on the oxygen fraction of sputter gas, and in particular the composition of the film deposited in sputter gas with an oxygen fraction of R = 10% was Ce$\_$0.23/Y$\_$1.30/Fe$\_$3.50/O$\_$12/. With raising the temperature of post-deposition heat-treatment from 900 $\^{C}$ to 1100 $\^{C}$, the surface roughness of the film on GGG substrates increased from about 3 nm to 40 nm, but their coercive force and ferromagnetic resonance line width decreased from 0.477 kA/m to 0.369 kA/m and from 12.5 kA/m to 8.36 kA/m, respectively.

• KSBB Journal
• /
• v.15 no.5
• /
• pp.438-443
• /
• 2000

Continuous processes using immobilized yeast were investigated in order to shorten beer maturation time. Three silica-based ceramic media and one cellulose-based medium were used. Diacetyl (DA) was one of the most distinctive compounds causing immature flavors. Heat treatment of green beer (GB) to convert a-acetolactate to DA was essential to shorten the time for beer maturation. The longer heat treatment time was needed at the lower temperature. Oxygen concentration in GB had a large influence on the conversion of a-acetolactate to DA. The lower the oxygen concentration in GB, the lower conversion ratio to DA. Heat treated GB was fed continuously to four kinds of immobilized yeast columns. DA concentration after immobilization columns was reduced to less than 0.1ppm at $3∼5^{\circ}C$ 180∼150 minutes retention time in all columns tested. This concentration is enough to fit the quality speification of commercialized product. Formation of a-acetolactate from residual sugars was higher in ceramic media column than cellulose media cloumn. The taste of beers from test processes were not the same as that of traditionally produced beer, but no off-flavors were detected in test samples, which shows that immobilized yeast columns have potentials as rapid processes for beer maturation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.5
• /
• pp.536-541
• /
• 2015

Copper has been used extensively as an electric wire or as a base material in various types of machineries owing to its good electrical and thermal conductivity and good fabricating property, as well as its good corrosion resistance compared to iron. Furthermore, the copper-nickel alloy has significant corrosion resistance in severely corrosive environments. Although, cupro-nickel alloy shows better corrosion resistance than the brass and bronze series, this alloy also corroded in severely corrosive environments, including aggressive chloride ions, dissolved oxygen, and condition of fast flowing seawater. In this study, and annealing treatment at various annealing temperatures was carried out on the cupro-nickel (Cu-10%Ni) alloy, and the effects of annealing were investigated using electrochemical methods, such as measuring the polarization and impedance behaviors under flowing seawater conditions. The corrosion resistance increased by annealing compared to non heat treatment in the absence of flowing seawater. In particular, the sample annealed at $200^{\circ}C$ exhibited the best corrosion resistance. The impedance in the presence of flowing seawater showed higher values than in the absence of flowing seawater. Furthermore, the highest impedances was observed in the sample annealed at $800^{\circ}C$, irrespective of the present of flowing seawater. Consequently, the corrosion resistance of cupro-nickel (Cu-10%Ni) alloy in a severely corrosive environment can be improved somewhat by annealing.

• Journal of the Korean Ceramic Society
• /
• v.50 no.3
• /
• pp.180-185
• /
• 2013

We investigated the characteristics of hot-pressed pure yttria ceramics, and annealed them in an oxidation atmosphere. Regardless of the heat treatment in the oxidation atmosphere, XRD analysis showed that all the samples had a $Y_2O_3$ phase without structural change. Even though the color variation of the hot-pressed $Y_2O_3$ ceramics was due to the sintering temperatures, the oxidation process turned the color of the $Y_2O_3$ ceramics into white. The color change during oxidation treatment appears to be related to oxygen defects. In addition, oxygen defects also affected the weight change and microstructure of the $Y_2O_3$ ceramics. The $Y_2O_3$ ceramic sintered at $1600^{\circ}C$ had a $5.03g/cm^3$ density, which is close to the theoretical density of $Y_2O_3$. As the sintering temperature increased, small homogeneous grains grew to large grains which affected the Vickers hardness. $Y_2O_3$ ceramics hot-pressed at $1600^{\circ}C$ and annealed at $1200^{\circ}C$ had a flexural strength of 140MPa.

• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.372-376
• /
• 2005

Respiratory characteristics and quality of Fuji apple were investigated at critical conditions for dipping treatment in mild hot water ($40-65^^{\circ}C$) to extend freshness. Dipping treatment conditions under which no damages occurred in peel and flesh of apples stored at $0^{\circ}C$ for 1 month after treatment were: 180 min at $40^{\circ}C$, 60 min at $45^{\circ}C$, 45 min at $50^{\circ}C$, 3 min at $55^{\circ}C$, 1 min at $60^{\circ}C$, and 20 sec at $65^{\circ}C$. Internal carbon dioxide concentrations of apples drastically increased immediately after treatments at 40, 45, and $50^{\circ}C$, then decreased to normal level 1 day after treatment at $0^{\circ}C$. Although internal oxygen concentration of apples showed reversed trend to internal carbon dioxide, no significant differences were observed in concentrations of carbon dioxide and oxygen during storage after treatment of apples at 55, 60, and $65^{\circ}C$. Concentration of internal ethylene of apples treated at 40, 45, and $50^{\circ}C$ increased, similarly to that of carbon dioxide upon heat treatment, then, during storage, decreased to below levels of control and apples treated at 55, 60, and $65^{\circ}C$. Firmness of apples treated at 45 and $50^{\circ}C$ were 6.42 and 10.53% higher than that of control at $0^{\circ}C$ after 7 days after treatment.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.188-192
• /
• 2005

The conversions to SiC-based ceramics of a polycarbosilane (PCS) with and without oxidation curing were carried out. A yield and an oxygen content of conversed SiC-based ceramics were evaluated. The weight losses of conversed SiC-based ceramics by both processes analyzed to estimate the high temperature stability after heat treatment at high temperature in vacuum. The yield of SiC­based ceramics after oxidation curing was higher than that without curing process. However, the weight loss of SiC-based ceramics with oxidation curing was larger than that without curing process after heat treatment.