• Journal of Dental Rehabilitation and Applied Science
• /
• v.16 no.3
• /
• pp.197-210
• /
• 2000

Surface roughness is one of implant surface topography and it's found that surface roughness characterizations, such as surface energy, oxide layer thickness and its chemical composition, are closely correlated if the roughness is changed. Several studies showed the importance of analyzing surface structure so the surface structure of thread implant was analyzed to measure the implant quality exactly. In this study, surface roughness of 4 implants - MK $II^{(R)}$(Nobel Biocare), $RBM^{(R)}$(Life-Core, USA), $Osseotite^{(R)}$(3i, USA), $TPS^{(R)}$(Life-Core, USA) - were measured using $Accura^{(R)}$ and 40 implants were installed into 4 sets of ten bovine ribs based on the parameters from the measurements. From this test, the following conclusions for the initial stability were drawn by measuring and comparing RFA, Periotest Value (PTV), Removal Torgue Value (RTV). 1. $R_a$ value in surface roughness measurement was increasing by the order of $MKII^{(R)}$, $Osseotite^{(R)}$, $RBM^{(R)}$, $TPS^{(R)}$ and $R_q$ value was the same order. 2. $R_q$ value in each section was observed to increase by the order of $MKII^{(R)}$, $Osseotite^{(R)}$, $RBM^{(R)}$, $TPS^{(R)}$ in top and $MKII^{(R)}$, $RBM^{(R)}$, $Osseotite^{(R)}$, $TPS^{(R)}$ in mid-section but the value of $MKII^{(R)}$ bottom was the lowest, followed by $Osseotite^{(R)}$, $RBM^{(R)}$ and $TPS^{(R)}$. 3. RFA increased by the order of $RBM^{(R)}$(7042Hz), $MKII^{(R)}$(7047Hz), $Osseotite^{(R)}$(7076Hz), $TPS^{(R)}$(7168Hz) and there was no significance between each group. 4. PTV was increasing by the order of $MKII^{(R)}$(-1.62), $TPS^{(R)}$(-1.92), $Osseotite^{(R)}$ & $RBM^{(R)}$(-2.08) and there was no significance, either. 5. Removal torque in RTV measurement showed the increasing order of $MKII^{(R)}(5.31kgf{\cdot}cm)$, $Oeeotite^{(R)}(5.71kgf{\cdot}cm)$, $TPS^{(R)}(5.92kgf{\cdot}cm)$ and $RBM^{(R)}(7.24kgf{\cdot}cm)$ and there was no significance among groups. Above observations explains that surface roughness does not make any impact on the initial stability of implants installation.

• Journal of the Korean Magnetics Society
• /
• v.17 no.4
• /
• pp.166-171
• /
• 2007

We report the magneto-transport properties of an individual single crystalline Bi nanowire grown by a spontaneous growth method. We have successfully fabricated a four-terminal device based on an individual 400-nm-diameter nanowire using plasma etching technique to remove an oxide layer forming on the outer surface of the nanowire. The transverse MR (2496% at 110 K) and longitudinal MR ratios (38% at 2 K) for the Bi nanowire were found to be the largest known values in Bi nanowires. This result demonstrates that the Bi nanowires grown by the spontaneous growth method are the highest-quality single crystalline in the literatures ever reported. We find that temperature dependence of Fermi energy ($E_F$) and band overlap (${\triangle}_0$) leads to the imbalance between electron concentration ($n_e$) and hole concentration ($n_h$) in the Bi nanowire, which is good agreement with the calculated $n_e\;and\;n_h$ from the respective density of states, N(E), for electrons and holes. We also find that the imbalance of $n_e\;and\;n_h$ plays a crucial role in determining magnetoresistance (MR) at T<75 K for $R_T$ and at T<205 K for $R_L$, while mean-free path is responsible for MR at T>75 K for $R_T$ and T>205 K for $R_L$.

• Journal of the Korean Vacuum Society
• /
• v.19 no.2
• /
• pp.128-133
• /
• 2010

ZnO:Al films were deposited by DC-pulsed magnetron sputtering using a two-step process involving the control of the oxygen pressure. The seed layers were prepared with various Ar to oxygen flow ratios and the bulk layers were deposited under pure Ar. As the oxygen pressure during the deposition of the seed layer increased, the crystallinity and degree of (002) texturing increased. The resistivity gradually decreased with increasing crystallinity from $4.7\times10^4\Omega{\cdot}cm$ (no seed) to $3.7\times10^4\Omega{\cdot}cm$ (Ar/$O_2$ = 9/1). The etched surface showed a crater-like structure and an abrupt morphology change appeared as the crystallinity was increased. The sample deposited at an Ar/$O_2$ flow ratio of 9/1 showed a very high haze value of 88% at 500 nm, which was explained by the large feature size of the craters, as shown in the AFM image.

• Membrane Journal
• /
• v.13 no.3
• /
• pp.162-173
• /
• 2003

The pseudo n-type polyaniline was prepared by doping of camphorsulfonic acid(CSA) and dodecylbenzenesulfonic acid(DBSA) as the dopants in solvent of N-methyl-2-pyrrolidinone(NMP). The dopants in polymer structure was qualitatively analyzed using FT-IR. The influence on electrochemical properties with dopant concentration of PANI film were investigated. The electrochemical characteristics of the n-type PANI electrode that coated on ITO were evaluated by cyclic voltammetry(CV) and AC impedance method. The prepared PANI were confirmed as n-type PANI from FT-IR and CV. The charge transfer resistance of film on PANI/CSA electrode were measured as 1.14{\sim}1.09k{\mu}$by AC impedance. The charge transfer resistance of PANI/DBSA electrode decreased with increasing the mole ratio of DBSA as 27.73{\sim}8.37 k{\mu}$. The double layer capacitance of PANI/CSA electrode was showed almost constant value as $13.47{\sim}14.59 {\mu}F$ and that of PANI/DBSA electrode increased with increasing mole ratio of DBSA from 0.49 to $1.20 {\mu}F$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.139-139
• /
• 2010

금속 실리사이드 나노입자는 열적 및 화학적 안정성이 뛰어나고, 절연막내에 일함수 차이에 따라 깊은 양자 우물구조가 형성되어 비휘발성 메모리 소자를 제작할 수 있다. 그러나 단일 $SiO_2$ 절연막을 사용하였을 경우 저장된 전하의 정보 저장능력 및 쓰기/지우기 시간을 향상시키는 데 물리적 두께에 따른 제한이 따른다. 본 연구에서는 터널장벽 엔지니어링을 통하여 물리적인 두께는 단일 $SiO_2$ 보다는 두꺼우나 쓰기/지우기 동작을 위하여 인가되는 전기장에 의하여 상대적으로 전자가 느끼는 상대적인 터널 절연막 두께를 감소시키는 방법으로 동작속도를 향상 시킨 $SiO_2/Si_3N_4/SiO_2$ 및 $Si_3N_4/SiO_2/Si_3N_4$ 터널 절연막을 사용한 금속 실리사이드 나노입자 비휘발성 메모리를 제조하였다. 제조방법은 우선 p-type 실리콘 웨이퍼 위에 100 nm 두께로 증착된 Poly-Si 층을 형성 한 이후 소스와 드레인 영역을 리소그래피 방법으로 형성시켜 트랜지스터의 채널을 형성한 이후 그 상부에 $SiO_2/Si_3N_4/SiO_2$ (2 nm/ 2 nm/ 3 nm) 및 $Si_3N_4/SiO_2/Si_3N_4$ (2 nm/ 3 nm/ 3 nm)를 화학적 증기 증착(chemical vapor deposition)방법으로 형성 시킨 이후, direct current magnetron sputtering 방법을 이용하여 2~5 nm 두께의 $WSi_2$ 및 $TiSi_2$ 박막을 증착하였으며, 나노입자 형성을 위하여 rapid thermal annealing(RTA) system을 이용하여 $800{\sim}1000^{\circ}C$에서 질소($N_2$) 분위기로 1~5분 동안 열처리를 하였다. 이후 radio frequency magnetron sputtering을 이용하여 $SiO_2$ control oxide layer를 30 nm로 증착한 후, RTA system을 이용하여 $900^{\circ}C$에서 30초 동안 $N_2$ 분위기에서 후 열처리를 하였다. 마지막으로 thermal evaporator system을 이용하여 Al 전극을 200 nm 증착한 이후 리소그래피와 식각 공정을 통하여 채널 폭/길이 $2{\sim}5{\mu}m$인 비휘발성 메모리 소자를 제작하였다. 제작된 비휘발성 메모리 소자는 HP 4156A semiconductor parameter analyzer와 Agilent 81101A pulse generator를 이용하여 전기적 특성을 확인 하였으며, 측정 온도를 $25^{\circ}C$, $85^{\circ}C$, $125^{\circ}C$로 변화시켜가며 제작된 비휘발성 메모리 소자의 열적 안정성에 관하여 연구하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.459-463
• /
• 2017

Hot dip galvanizing in the steel plant is one of the most widely used methods for preventing the corrosion of steel materials including structures, steel sheets, and materials for industrial facilities. While hot dip galvanizing has the advantage of stability and economic feasibility, it has difficulty in repairing equipment and maintaining the facilities due to high-temperature oxidation caused by Zn Fume where molten zinc used in the open spaces. Currently, SM45C (carbon steel plate for mechanical structure, KS standard) is used for the equipment. If a part of the equipment is resistant to high temperature and Zn fume, it is expected to improve equipment life and performance. In this study, the manufactured Ni alloy was tested for its corrosion resistance against Zn fume when it was used in the hot dip galvanizing equipment in the steel plant. Two kinds of materials currently used in the equipment, new Ni alloy and Inconel(typical corrosion-resistant Ni alloy), were selected as the reference groups. Two kinds of molten metal were used to confirm the corrosion of each alloy according to the molten metal. Zn fume was generated by bubbling Ar gas from molten Zn in a furnace($500{\sim}700^{\circ}C$) and the samples were analyzed after 30 days. After 30 days, the specimens were taken out, the oxide layer on the surface was confirmed with an optical microscope and SEM, and the corrosion was confirmed using a potentiodynamic polarization test. Corrosion depends on the type of molten metal.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.4
• /
• pp.207-213
• /
• 2018

Not only efficiency of chlorine evolution reaction (CER) but also durability namely service life is very important property in dimensional stable anode for Ballast Water Management System (BWMS) for marine ships. Many researchers have been focused on improving efficiency of CER by controlling composition, phase and surface area for a long time, but the efforts to increase durability was relatively small. In this study, we have investigated the effect of $TiO_2$ protective interlayers on efficiency and durability of DSA electrodes. $TiO_2$ protective interlayers were prepared by thermal oxidation at 500, 600 and $700^{\circ}C$ on Ti substrate. And then the DSA electrodes consisting of $Ti/RuO_2-PdO-TiO_2$ were prepared by thermal decomposition method on $TiO_2$ interlayers. The efficiencies of CER of DSA electrodes without $TiO_2$ interlayer and with $TiO_2$ interlayer grown at 500, 600 and $700^{\circ}C$ were 94.19, 94.45, 84.60 and 76.75% respectively. On the otherhand, durabilities were 30, 55, 90 and 65 hours respectively. In terms of industrial aspect, the performance of DSA is considered high efficiency and durability which can correspond to total production of chlorine. If we considered the performance index of DSA as the product of efficiency and durability, performance indices could be recalculated as 28.26, 50.85, 76.14 and 49.89 respectively. As the thermal oxidation temperature increasing, life time were increased remarkerbly, while efficiency of CER was decreased slightly. As a result, DSA electrode with $TiO_2$ interlayer grown at $600^{\circ}C$ has shown about 2.7 times performace of original DSA electrode without $TiO_2$ interlayer.

• Korean Journal of Environment and Ecology
• /
• v.33 no.5
• /
• pp.596-604
• /
• 2019

This study conducted a sediment culture experiment to investigate the effects of sediment oxygen demand (SOD) and environmental factors on sediment and water quality. We installed a leaching tank in the laboratory, cultured it for 20 days, and analyzed the relationship between P and Fe in the sediment. As a result, the dissolved oxygen of the water layer decreased with time, while the oxidation-reduction potential of the sediment progressed in the negative direction to form an anaerobic reducing environment. The SOD was measured to be 0.05 mg/g at the initial stage of cultivation and increased to 0.09 mg/g on the 20th day, indicating the tendency of increasing consumption of oxygen by the sediment. The change is likely to have caused by oxygen consumption from biological-SOD, which is the decomposition of organic matter accumulated on the sediment surface due to the increase of chl-a, and chemical-SOD consumed when the metal-reducing product produced by the reduction reaction is reoxidized. The correlation between SOD and causality for sediment-extracted sediments was positive for Ex-P and Org-P and negative for Fe-P. The analysis of the microbial community in the sediment on the 20th day showed that anaerobic iron-reducing bacteria (FeRB) were the dominant species. Therefore, when the phosphate bonded to the iron oxide is separated by the reduction reaction, the phosphate is eluted into the water to increase the primary productivity. The reduced substance is reoxidized and contributes to the oxygen consumption of the sediment. The results of this study would be useful as the reference information to improve oxygen resin.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.34 no.3
• /
• pp.167-173
• /
• 2008

Pearlescent pigments have been widely used in cosmetic applications. Up to date; the most widely used pearl effect pigment is the mica-based pigment, which uses natural mica as the substrate that is in turn coated with metal of oxide interference layer. However, when natural mica is employed as a base material the final product often has a yellowish color, mainly due to the fact that natural mica contains low levels of iron as an impurity[1,2]. This study was focused on developing a pearl pigment which might have a similar sparkling effect as snow. This effect was found to be due to its structure and purity, and this concept was also applied to development of our pearl pigments. More specifically, this invented pearl effect pigments are the mixture of glass-flake and glass-flake coated metal oxides and present the optical properties of snow matrix such as refractive index and particle size, unlike only the glass-flake or glass-flake coated metal oxides to be applied in. Using base material having similar physical properties (refractive index and particle size) as snow matrix as platelet for pearl effect pigments, these invented pigments present a three-dimensional glittering effect of the snow matrix. With this invented figments an applied; we achieved the beauty of snow crystal from makeup products containing these pigments.

• Nuclear Engineering and Technology
• /
• v.49 no.5
• /
• pp.1044-1062
• /
• 2017

The construction project of the Kijang research reactor (KJRR), which is the second research reactor in Korea, has been launched. The KJRR was designed to use, for the first time, U-Mo fuel. Plate-type U-7 wt.% Mo/Al-5 wt.% Si, referred to as U-7Mo/Ale5Si, dispersion fuel with a uranium loading of $8.0gU/cm^3$, was selected to achieve higher fuel efficiency and performance than are possible when using $U_3Si_2/Al$ dispersion fuel. To qualify the U-Mo fuel in terms of plate geometry, the first miniplates [HANARO Miniplate (HAMP-1)], containing U-7Mo/Al-5Si dispersion fuel ($8gU/cm^3$), were fabricated at the Korea Atomic Energy Research Institute and recently irradiated at HANARO. The PIE (Post-irradiation Examination) results of the HAMP-1 irradiation test were analyzed in depth in order to verify the safe in-pile performance of the U-7Mo/Al-5Si dispersion fuel under the KJRR irradiation conditions. Nondestructive analyses included visual inspection, gamma spectrometric mapping, and two-dimensional measurements of the plate thickness and oxide thickness. Destructive PIE work was also carried out, focusing on characterization of the microstructural behavior using optical microscopy and scanning electron microscopy. Electron probe microanalysis was also used to measure the elemental concentrations in the interaction layer formed between the U-Mo kernels and the matrix. A blistering threshold test and a bending test were performed on the irradiated HAMP-1 miniplates that were saved from the destructive tests. Swelling evaluation of the U-Mo fuel was also conducted using two methods: plate thickness measurement and meat thickness measurement.