• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1553-1555
• /
• 2003

Coatings on glass with highly transparent conducting oxide films(TCOs) are performed mostly by using indium tin oxide(ITO). This Oxide material is very common for applications where both high electrical conductivity. Photovoltaic cells, transparent electrical heater, selective optical filter, and a optical transmittance are essential. In this study, ITO thin films were deposited on $SiO_2$/soda-line glass plates by a dc magnetron sputtering technique. The crystallinity and electrical properties of the films were investigated by X-ray diffraction(XRD), atomic force microscopy(AFM) scanning and 4-point probe. The optical transmittance of ITO films in the range of 300-800nm were measured with a spectrophotometer. As a result, we obtained polycrystalline structured ITO films with (222), (400), and (440) peak. Transmittance of all the films were higher than 90% in the visible range.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.901-904
• /
• 2000

In order to investigate the effect of deposition conditions on crystallographic properties of ZnO thin films by Facing Targets Sputtering system which can deposit thin films in plasma-free situation and change the deposition conditions in wide range. The characteristics of zinc oxide thin films on power, inter targets distance, and substrate temperature were investigated by XRD(x-ray diffractometer), alpha-step (Tencor) analyses. The excellently c-axis oriented zinc oxide thin films were obtained at sputter pressure 1mTorr, sputtering current 0.4A, substrate temperature 300$^{\circ}C$, inter target distance 100mm. In these conditions, the rocking curve of zinc oxide thin films deposited on Glass was 3.9$^{\circ}$.

• Transactions on Electrical and Electronic Materials
• /
• 제11권5호
• /
• pp.222-225
• /
• 2010

The preparation of tin oxide thin films by atomic layer deposition (ALD), using a tetrakis (ethylmethylamino) tin precursor, and the effects of a seed layer on film growth were examined. The average growth rate of tin oxide films was approximately 1.2 to 1.4 A/cycle from $50^{\circ}C$ to $150^{\circ}C$. The rate rapidly decreased at the substrate temperature at $200^{\circ}C$. A seed effect was not observed in the crystal growth of tin oxide. However, crystallinity and the growth of seed material were detected by XPS after thermal annealing. ALD-grown seeded tin oxide thin films, as-deposited and after thermal annealing, were characterized by X-ray diffraction, atomic force microscopy and XPS.

• 센서학회지
• /
• 제24권5호
• /
• pp.348-352
• /
• 2015

Thin nickel oxide films formed on uncooled and cooled $SiO_2/Si$ substrates using a radio frequency (RF) magnetron sputter powered by 200 W in a mixed atmosphere of argon and oxygen. Grazing-incidence X-ray diffraction and field emission scanning electron microscopy are used for the structural analysis of nickel oxide films. The electrical conductivity required for better bolometric performance is estimated by means of a four-point probe system. Columnar and (200) preferred orientations are discovered in both films regardless of substrate cooling. Electric resistivity, however, is greatly influenced by the substrate cooling. Oxygen partial pressure increase during the nickel oxide deposition leads to a rapid decrease in resistivity, and the resistivity is higher in the cooled nickel oxide samples. Even when small microstructure variations are applied, lower resistivity in favor of low noise performance is acquired in the uncooled samples.

• Bulletin of the Korean Chemical Society
• /
• 제32권9호
• /
• pp.3395-3399
• /
• 2011

Copper oxide thin films were synthesized by reactive radio frequency magnetron sputtering at different oxygen gas ratios. The chemical and physical properties of the thin films were investigated by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray diffraction (XRD). XPS results revealed that the dominant oxidation states of Cu were $Cu^0$ and $Cu^+$ at 0% oxygen ratio. When the oxygen ratios increased above 5%, Cu was oxidized as CuO as detected by X-ray induced Auger electron spectroscopy and the $Cu(OH)_2$ phase was confirmed independent of the oxygen ratio. The valence band maxima were $1.19{\pm}0.09$ eV and an increase in the density of states was confirmed after formation of CuO. The thickness and roughness of copper oxide thin films decreased with increasing oxygen ratio. The crystallinity of the copper oxide films changed from cubic Cu through cubic $Cu_2O$ to monoclinic CuO with mean crystallite sizes of 8.8 nm (Cu) and 16.9 nm (CuO) at the 10% oxygen ratio level.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.409-414
• /
• 1999

The influence of ion beam energy and reactive oxygen partial pressure on the electrical and crystallographic characteristics of transition metal oxide compound(Cr0x) film was studied in this paper. Chromium oxide films were prepared onto the coverglass using Ion Beam Sputter Deposition(1BSD) technique according to the processing conditions of the partial pressure of reactive oxygen gas and ion beam energy. Crystallinity and grain size of as-deposited films were analyzed using XRD analysis. Thickness and Resistivity of the films were measured by $\alpha$-step and 4-point probe measurement. As results, according to the XRD, XPS and resistivity measurement, the deposited films were the cermet type films which has a crystal structure including amorphous oxide(a-oxide) phase and metal Cr phase simultaneously. The increasernent of the ion b m energy during the deposition process happened to decreasernent of metal Cr grain size and the rapid change of resistivity above the critical $O_2$ partial pressure.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.208-208
• /
• 2010

Indium zinc tin oxide (IZTO) thin films were studied as a possible alternative to indium tin oxide (ITO) films for providing low-cost transparent conducting oxide (TCO) for thin film photovoltaic devices. IZTO films were deposited onto glass substrates at room temperature. A dc/rf magnetron co-sputtering system equipped with a ceramic target of the same composition was used to deposit TCO films. Earlier studies showed that the resistivity value of $In_{0.6}Zn_{0.2}Sn_{0.2}O_{1.5}$ (IZTO20) films could be lowered to approximately $6{\times}10^{-4}ohm{\cdot}cm$ without sacrificing optical transparency and still maintaining amorphous structure through the optimization of process variables. The growth rate was kept at about 8 nm/min while the oxygen-to-argon pressure ratio varied from 0% to 7.5%. As-deposited films were always amorphous and showed strong oxygen pressure dependence of electrical resistivity and electron concentration values. Influence of forming gas anneal (FGA) at medium temperatures was also studied and proven effective in improving electrical properties. In this study, the chemical composition of the targets and the films varied around the $In_{0.6}Zn_{0.2}Sn_{0.2}O_{1.5}$ (IZTO20). It was the main objective of this paper to investigate how off-stoichiometry affected TCO characteristics including electrical resistivity and optical transmission. In addition to the composition effect, we have also studied how film properties changed with processing variables. IZTO thin films have shown their potential as a possible alternative to ITO thin films, in such way that they could be adopted in some applications where currently ITO and IZO thin films are being used. Our experimental results are compared to those obtained for commercial ITO thin films from solar cell application view point.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.49.2-49.2
• /
• 2010

Copper oxide films have been deposited on silicon substrates by direct current magnetron sputtering of Cu in O2 / Ar gas mixtures. The target oxidation occurring as a result of either adsorption or ion-plating of reactive gases to the target has a direct effect on the discharge current and the resulting composition of the deposited films. The kinetic model which relates the target oxidation to the discharge current was proposed, showing the one-to-one relationship between discharge current characteristics and film stoichiometry of the deposited films.

• Journal of Korean Vacuum Science & Technology
• /
• 제2권2호
• /
• pp.85-91
• /
• 1998

The electrochromic behaviors of de-magnetron sputtered tungsten oxide thin films were investigated during coloration and bleach cycles using in situ real-time spectroscopic ellipsometry. Effective medium approximation and least-squares regression analyses were employed to investigate the electrochromic process. The optical properties of the tungsten oxide film were analyzed using the oscillator model and the evolution of the process using a reaction-limited model. In these analyses, we found that two different reaction rates were associated with the process. We ascribe this behavior to the microstructure of this films.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.783-786
• /
• 2003

Thin films of vanadium oxide(VOx) have been deposited by r.f. magnetron sputtering from $V_2O_5$ target in gas mixture of argon and oxygen. The oxygen/(oxygen+argon) partial pressure ratio of 0% and 8% is adopted. Crystal structure and optical properties of films sputter-deposited under different oxygen gas pressures and in situ annealed in vacuum at $400^{\circ}C$ for 1h and 4h are characterized through XRD and optical absorption measurements. The films as-deposited are amorphous, but $0%O_2$ films annealed for time longer than 4h and $8%O_2$ films annealed for time longer than 1h are polycrystalline. The optical transmission of the films annealed in vacuum decreases considerably than the as-deposited films and the optical absorption of all the films increases rapidly at wavelength shorter than about 550nm. Indirect and direct optical band gaps were decreased with increasing the annealing time.