• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.89-89
• /
• 2011

a-GIZO(비정질 Ga-In-Zn-O)박막은 유연하며 광학적으로 투명하고 높은 전자의 이동도를 갖는 반도체적 특성을 갖기 때문에 차세대 display분야에서 TFT(Thin-Film-Transistor)의 high speed active-matrix layer로써 각광을 받고 있다. 이 물질의 표면은 환경 및 표면처리에 매우 민감하며 [1,2], 이 표면에 metal이 증착되는 경우에도, 선행 연구에 의하면, 다양한 chemical state가 나타남을 알 수 있었다. 이것은 metal의 증착에 따라 metal과 a-GIZO 사이의 contact 저항이 달라짐을 의미한다. 우리는 a-GIZO 박막 위에 Au를 단계적으로 증착시키면서, Au coverage 증가에 따른 core-level과 valence에서의 x-ray photoelectron spectra의 변화를 살펴봄으로써 a-GIZO박막과 Au의 계면에서 일어나는 chemical state의 변화를 알 수 있었다. 특히, Au deposition의 전 처리과정으로써 Ne ion sputtering을 두 단계로 다르게 하여 a-GIZO의 표면환경에 따른 Au 증착의 영향을 살펴보았다.

• 한국표면공학회지
• /
• 제44권4호
• /
• pp.144-148
• /
• 2011

$Ga_2O_3$ doped $SnO_2$ thin films were grown by using pulsed laser deposition (PLD) technique on glass substrate. The optical and electrical properties of these films were investigated for different doping concentrations, oxygen partial pressures, substrate temperatures, and film thickness. The films were deposited at different substrate temperatures (room temperature to $600^{\circ}C$). The best opto-electrical properties is shown by the film deposited at substrate temperature of $300^{\circ}C$ with oxygen partial pressure of 80 m Torr and the gallium concentration of 2 wt%. The as obtained lowest resistivity is $9.57{\times}10^{-3}\;{\Omega}cm$ with the average transmission of 80% in the visible region and an optical band gap (indirect allowed) of 4.26 eV.

• Macromolecular Research
• /
• 제14권1호
• /
• pp.38-44
• /
• 2006

Vacuum deposited copper phthalocyanine (CuPc) was placed as a thin interlayer between indium tin oxide (ITO) electrode and a hole transporting layer (HTL) in a multi-layered, organic, light-emitting diode (OLEOs). The well-stacked CuPc layer increased the stability and efficiency of the devices. Thermal annealing after CuPc deposition and magnetic field treatment during CuPc deposition were performed to obtain a stacked-CuPc layer; the former increased the stacking density of the CuPc molecules and the alignment of the CuPc film. Thermal annealing at about 100$^{circ}C$ increased the current flow through the CuPc layer by over 25$\%$. Surface roughness decreased from 4.12 to 3.65 nm and spikes were lowered at the film surface as well. However, magnetic field treatment during deposition was less effective than thermal treatment. Eventually, a higher luminescence at a given voltage was obtained when a thermally-annealed CuPc layer was placed in the present, multi-layered, ITO/CuPc/NPD/Alq3/LiF/AI devices. Thermal annealing at about 100$^{circ}C$ for 3 h produced the most efficient, multi-layered EL devices in the present study.

• Bulletin of the Korean Chemical Society
• /
• 제35권2호
• /
• pp.353-356
• /
• 2014

We fabricated organic photovoltaic (OPV) based on ZnO ripple structure on indium tin oxide as electron-collecting layers and PTB7-F20 as donor polymer. In addition, atomic layer deposition (ALD) was used for preparing additional ZnO layers on rippled ZnO. Addition of 2 nm-thick ALD-ZnO resulted in enhanced initial OPV performance and stability. Based on photoluminescence results, we suggest that ALD-ZnO layers reduced number of surface defect sites on ZnO, which can act as electron-hole recombination center of OPV, and increased resistance of ZnO towards surface defect formation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.433-433
• /
• 2013

Graphene, $sp^2$-hybridized 2-Dimension carbon material, has drawn enormous attention due to its desirable performance of excellent properties. Graphene can be applied for many electronic devices such as field-effect transistors (FETs), touch screen, solar cells. Furthermore, indium tin oxide (ITO) is commercially used and sets the standard for transparent electrode. However, ITO has certain limitations, such as increasing cost due to indium scarcity, instability in acid and basic environments, high surface roughness and brittle. Due to those reasons, graphene will be a perfect substitute as a transparent electrode. We report the graphene synthesized by inductive coupled plasma enhanced chemical vapor deposition (ICP-PECVD) process on Cu substrate. The growth was carried out using low temperature at $400^{\circ}C$ rather than typical chemical vapor deposition (CVD) process at $1,000^{\circ}C$ The low-temperature process has advantage of low cost and also low melting point materials will be available to synthesize graphene as substrate, but the drawback is low quality. To improve the quality, the factor affect the quality of graphene was be investigated by changing the plasma power, the flow rate of precursors, the scenario of precursors. Then, graphene film's quality was investigated with Raman spectroscopy and sheet resistance and optical emission spectroscopy.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.175-175
• /
• 2008

투명전극으로 사용되고 있는 Indium tin oxide (ITO) 박막은 전기적 전도도와 기판과의 접확성, 화학적 안정성, 광투과율 등의 특성과 함께 우수한 전기 광학적 거동을 보이고 있다. 그러나 ITO는 고가의 재료이기 때문에 대체 투명전극으로 Al을 도핑한 ZnO 박막의 연구가 활발히 진행되고 있다. ZnO:Al 박막은 chemical vapor deposition, reactive magnetron sputtering, electron-beam evaporation, pulsed laser deposition 등의 당양한 방법을 이용하여 증착하였다. 그러나 최근 낮은 온도에서 대면적의 균일성과 우수한 특성 때문에 atomic layer depositon (ALD) 방법을 이용하여 많은 연구가 진행되고 있으며, 이런 투명전극은 태양전지를 위해 연구되어지고 있다. 따라서 본 연구에서는 ALD 방법으로 Al의 도핑 양을 조절하여, ZnO:Al 박막을 제조하여 그 특성을 평가하고, 또한 ZnO TFT를 제작하여 발표하고자 한다. ZnO와 ZnO:Al 박막은 실리콘과 유리 기판 위에 ALD (Lucida-D200, NCD Technology) 장치로 증착하였다. DEZn, TMA, $H_2O$는 ZnO와 ZnO:Al 박막을 증착하기 위한 전구체와 반응가스로 사용하였다. 증착된 박막은 XRD와 HRTEM을 이용하여 결정구조와 미세구조를 분석하였다. AFM과 4-point probe를 이용하여 증착된 박막의 표면 거칠기와 면저항을 관찰하였다. semiconductor parameter 분석기를 이용하여 제작된 ZnO TFT를 평가하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.425-425
• /
• 2008

The transparent conducting oxides(TCOs) are widely used as electrodes for most flat panel display devices(FPDs), electrodes in solar cells and organic light emitting diodes(OLED). Among them, indium oxide materials are mostly used due to its high electrical conductivity and a high transmittance in the visible spectrum. The present study reports on a study of the electrical and optical properties of IGZO thin films prepared on glass and PET substrates by the combinational magnetron sputtering. We use the targets of IZO and Ga2O3 for the deposition process. In some case the deposition process is coupled with the End-Hall ion-beam treatment onto the substrates before the sputtering. In addition we control the deposition rate to optimize the film quality and to minimize the surface roughness. Then we investigate the effects of the Ar gas pressure and RF power during the sputtering process upon the electrical, optical and morphological properties of thin films. The properties of prepared IGZO thin films have been analyzed by using the XRD, AFM, a-step, 4-point probe, and UV spectrophotometer.

• Bulletin of the Korean Chemical Society
• /
• 제30권1호
• /
• pp.92-96
• /
• 2009

A new precursor [$Zr(acac)_{3}(H_{2}O)_{2}$] was synthesized by Sonochemical technique and used to deposit thin $ZrO_{2}$ film on quartz and ceramic substrate via ultrasonic aerosol assisted chemical vapour deposition (UAACVD) at 300 ${^{\circ}C}$ in oxygen environment followed by annealing of the sample for 2-3 minutes at 500 ${^{\circ}C}$ in nitrogen ambient. The molecular structure of the precursor determined by single crystal X-ray analysis revealed that the molecules are linked through intermolecular hydrogen bonds forming pseudo six and eight membered rings. DSC and TGA/FTIR techniques were used to determine thermal behavior and decomposition temperature of the precursor and nature of evolved gas products. The optical measurement of annealed $ZrO_{2}$ film with tetragonal phase shows optical energy band gap of 5.01 eV. The particle size, morphology, surface structure and composition of deposited films were investigated by XRD, SEM and EDX.

• 한국전기전자재료학회논문지
• /
• 제24권6호
• /
• pp.468-472
• /
• 2011

Conductive $SrMoO_3$ thin films were fabricated by RF magnetron sputtering with the powder-type sputtering target, and annealed for crystallization. When RTP (rapid thermal processing) in vacuum was applied, the fabricated thin films showed the mixed phases of $SrMoO_3$ and $SrMoO_4$, but $SrMoO_3$ phase could be promoted by the lowering of the working pressure during deposition. In order to eliminate $O_2$ gas during deposition and annealing, further lowering of the working pressure and furnace annealing in hydrogen atmosphere were tried. With the optimization of the deposition and annealing conditions, the thin film with nearly single-phase of $SrMoO_3$ was obtained, and it showed good electrical conduction properties with a low resistivity of $2.5{\times}10^{-3}{\Omega}{\cdot}cm$ at room temperature.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.100-100
• /
• 2000

Aluminium oxide (Al2O3) films have been investigated for many applications such as insulating materials, hard coatings, and diffusion barriers due to their attractive electrical and mechanical properties. In recent years, application of Al2O3 films for dielectric materials in integrated circuits as gates and capacitors has attracted much attention. Various deposition techniques such as sol-gel, metalorganic decomposition (MOD), sputtering, evaporation, metalorganic chemical vapor deposition (MOCVD), and pulsed laser ablation have been used to fabricate Al2O3 thin films. Among these techniques, reactive sputtering has been widely used due to its high deposition rate and easy control of film composition. It has been also reported that the sputtered Al2O3 films exhibit superior chemical stability and mechanical strength compared to the films fabricated by other processes. In this study, Al2O3 thin films were deposited on Pt/Ti/SiO/Si2 and Si substrates by DC reactive sputtering at room temperature with variation of the Ar/O2 ratio in sputtering ambient. Crystalline phase of the reactively sputtered films was characterized using X-ray diffractometry and the surface morphology of the films was observed with Scanning election microscopy. Effects of Th Ar/O2 ratio characteristics of Al2O3 films were investigated with emphasis on the thickness dependence of the dielectric properties. Correlation between the dielectric properties and the microstructure was also studied