• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.5
• /
• pp.1785-1795
• /
• 2013

Most of the previous models for analysis of shallow water flow assumed the uniform velocity distributions over the flow depth so that they produced incorrect velocity prediction at meandering part due to the ignorance of secondary current. In this study, the vertical velocity profiles in longitudinal and transverse direction were decomposed as the mean and variation components, which resulted in additional dispersion stresses terms in momentum equations. The proposed model were applied at the channels with $30^{\circ}$, $90^{\circ}$, $270^{\circ}$ bends, and shallow water flow in curved channel was analyzed using dispersion stresses. The dispersion stresses acted as a sink or source in the momentum equations, which caused the transverse convection of momentum to shift from the inner bank to the outer bank.

• Journal of Environmental Impact Assessment
• /
• v.14 no.6
• /
• pp.427-441
• /
• 2005

In order to choose proper dispersion model and emission factors suitable in Korea in evaluating the effect of pollutants emitted by the vehicles in highway on nearby area, various road dispersion models and vehicle emission factors were reviewed. With theoretical inter-comparisons of the exiting models for line source, CALINE 3 and CALINE 4 models which were suggested by US EPA were selected as the road dispersion models for further evaluation with the measurement. The emission factors suggested by Korean Ministry of Environment was turned out to be appropriate since the classification of vehicle kinds was simple and easy to apply in Korea. The comparisons of predicted concentrations by CALINE 3 and 4 models with the measurements in flat, fill and bridge road types showed that CO and PM-10 were in good agreements with experiments and the differences between CALINE 3 and 4 models are negligible. The model concentrations of $NO_2$ by CALINE 4 were also in good agreement with the measurement but those by CALINE 3 were over-predicted. The discrepancies in CALINE 3 model were due to rapid decay reaction of $NO_2$ near the highway, which was not included in CALINE 3 model. For the road type with one & two side cutting grounds, the similar patterns as the flat & fill road type for CO, PM10, & $NO_2$ were observed but the number of data for comparison in these cases were not enough to draw the conclusion. These results lead to the conclusion that CALINE4 model is proper in road environmental impact assessment near the highway in flat, fill and bridge road types.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.272-277
• /
• 2014

We studied in-line monitoring the dispersion of highly energetic material simulant by a twin screw extruder having a high temperature ultrasonic system. The simulant suspension system consisted of ethylene vinyl acetate and Dechlorane plus 25 as binder and filler, respectively. With increasing filling fraction, the ultrasonic velocity was not changed but the attenuation linearly decreased. It was possible to estimate the solid fraction of well dispersed suspension system by measuring ultrasonic attenuation. The ultrasonic attenuation of samples filled over 60 v% approached straight line with increasing filling fraction when the samples was extruded repeatedly. It was due to the enhanced dispersion of solid particles in the suspension system. It was believed that the degree of dispersion and filling fraction could be obtained by combination of on-line measurement like ultrasonic attenuation and off-line analysis like TGA and SEM with image analyzer.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.3
• /
• pp.211-223
• /
• 2000

The atmospheric dispersion of a pollutant emitted from a hypothetical source located in the middle of the Yochon Industrial Estate was simulated by using the Regional Atmospheric Modeling System (RAMS). Four horizontally nested grids were employed: the coarsest one covered the southern part of the Korean Peninsula including Mt. Chiri and the finest one covered the Yochon Industrial Estate and the surrounding area. Wind fields were initially assumed horizontally homogeneous with a wind speed of 4m/s, the average for the Yosu area, and were developed without both external forces and diurnal changes in order to investigate the terrain-induced phenomena. Wind directions that could emphasize the terrain effects on the pollutant transport and that could carry pollutants to a highly-popluated area were selected for the dispersion study. A pollutant was released for 24hours from a grid-base volume source after a 24-h blank run for developing the wind field. The dispersion study showed that the pollutant from the present source location did not directly affect the Yosu City, but showed high concentrations at locations behind the hills 5 to 6 km away from the source according to wind directions. When the wind speed was low, close to calm condition, the pollutant was detected at upstream locations 6 to 7 km from the source. In comparison with the results from the RAMS simulation, the Industrial Source Complex Short-Term Model(ISCST3) predicted a narrow dispersion that was sensitive to the wind direction. When the wind velocity was affected by the local environment, the ISCST3 calculation using that data also gave a lop-sided result, which was different from the distribution of the pollutant reproduced by RAMS.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.198-198
• /
• 2006

Tin doped $In_2O_3$ sputtering target is widely used to produce a various kinds of flat panel display because of high transmittance in visible region and high electrical conductivity. In2O3 and SnO2 powders were prepared by a homogeneous precipitation method using metal source, respectively, the calcining and sintering behavior of the indium-tin oxide(In2O3-SnO2) composite powders were studied. The tin oxide(SnO2) dispersion condition in ITO sputtering target was improved by increasing calcining temperature. And the tin oxide dispersion was also improved by reducing the tin oxide contents in the ITO target from 30 to 5wt%. SnO2 dispersion and densification of ITO target is very difficult to control due to sublimation of SnO2 at over 1150C.

• Journal of Radiation Protection and Research
• /
• v.41 no.3
• /
• pp.260-267
• /
• 2016

Background: This study analyzes the differences in the annual averaged atmospheric dispersion factor and ground deposition factor produced using two classification methods of atmospheric stability, which are based on a vertical temperature difference and the standard deviation of horizontal wind direction fluctuation. Materials and Methods: Daedeok and Wolsong nuclear sites were chosen for an assessment, and the meteorological data at 10 m were applied to the evaluation of atmospheric stability. The XOQDOQ software program was used to calculate atmospheric dispersion factors and ground deposition factors. The calculated distances were chosen at 400 m, 800 m, 1,200 m, 1,600 m, 2,400 m, and 3,200 m away from the radioactive material release points. Results and Discussion: All of the atmospheric dispersion factors generated using the atmospheric stability based on the vertical temperature difference were shown to be higher than those from the standard deviation of horizontal wind direction fluctuation. On the other hand, the ground deposition factors were shown to be same regardless of the classification method, as they were based on the graph obtained from empirical data presented in the Nuclear Regulatory Commission's Regulatory Guide 1.111, which is unrelated to the atmospheric stability for the ground level release. Conclusion: These results are based on the meteorological data collected over the course of one year at the specified sites; however, the classification method of atmospheric stability using the vertical temperature difference is expected to be more conservative.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.5
• /
• pp.390-397
• /
• 2010

0.5wt% Ru/$\alpha-Al_2O_3$ catalysts are prepared by deposition-precipitation method for the preferential CO oxidation In order to investigate the effect of pH on the Ru dispersion and particle size, the pH of precursor solution is adjusted to between 5.5 and 9.5. 0.5wt% Ru/$\alpha-Al_2O_3$ catalyst prepared at the pH of 6.5 has high Ru dispersion of 17.9% and small particle size of 7.7nm. In addition, 0.5wt% Ru/$\alpha-Al_2O_3$ catalyst prepared at the pH 6.5 is easily reduced at low temperatures below $150^{\circ}C$ due to high dispersion of $RuO_2$ particle and shows high CO conversion over 90% in the wide temperature range between $100^{\circ}C$ and $160^{\circ}C$. Moreover, the deposition-precipitation is a feasible method to improve the Ru dispersion as compared to the impregnation method. The 0.5wt% Ru/$\alpha-Al_2O_3$ catalyst prepared by deposition-precipitation exhibits higher CO conversion than 0.5wt% Ru/$\alpha-Al_2O_3$ catalysts prepared by impregnation due to higher metal dispersion and better reducibility at low temperature.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.5 no.4
• /
• pp.279-287
• /
• 1993

Three dimensional linear transient wave propagation over a constant depth is presented using Green's function method. Present solution is proved to be a more general solution from which the existing solutions are obtained by using the appropriate assumptions. The effect of dispersion on wave height attenuation is shown and discussed on the numerical results of the solution.

• Earthquakes and Structures
• /
• v.9 no.2
• /
• pp.305-320
• /
• 2015

The present paper is devoted to study SH-wave propagation in heterogeneous layer laying over an inhomogeneous isotropic elastic half-space. The dispersion relation for propagation of said waves is derived with Green's function method and Fourier transform. As a special case when the upper layer and lower half-space are homogeneous, our derived equation is in agreement with the general equation of Love wave. Numerically, it is observed that the velocity of SH-wave increases with the increase of inhomogeneity parameter.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.2
• /
• pp.79-93
• /
• 2015

Three-dimensional structures of large ocean rings in the Gulf Stream region are investigated using the HYbrid Coordinate Ocean Model (HYCOM). Numerically simulated flow structures around four selected cyclonic and anticyclonic rings are compared with two different horizontal resolutions: $1/12^{\circ}$ and $1/48^{\circ}$. The vertical distributions of Lagrangian Coherent Structures (LCSs) are analyzed using Finite Size Lyapunov Exponent (FSLE) and Okubo-Weiss parameters (OW). Curtain-shaped FSLE ridges are found in all four rings with extensions of surface ridges throughout the water columns, indicating that horizontal stirring is dominant over vertical motions. Near the high-resolution rings, many small-scale flow structures with size O(1~10) km are observed while these features are rarely found near the low-resolution rings. These small-scale structures affect the flow pattern around the rings as flow particles move more randomly in the high-resolution models. The dispersion rates are also affected by these small-scale structures as the relative horizontal dispersion coefficients are larger for the high-resolution models. The absolute vertical dispersion rates are, however, lower for the high-resolution models, because the particles tend to move along inclined eddy orbits when the resolution is low and this increases the magnitude of absolute vertical dispersion. Since relative vertical dispersion can reduce this effect from the orbital trajectories of particles, it gives a more reasonable magnitude range than absolute dispersion, and so is recommended in estimating vertical dispersion rates.