• 대한기계학회논문집B
• /
• 제27권8호
• /
• pp.1051-1060
• /
• 2003

The heat and mass transfer on two kinds of tube surfaces (bare stainless steel tube and Teflon coated tube) in steam-air mixture flow are experimentally studied to obtain design data for the heat exchanger of the latent heat recovery from flue gas. In the test section, 3-tubes are horizontally installed, and steam-air mixture is vertically flowed from the top to the bottom. The pitch between tubes is 67mm, the out-diameter of tube is 25.4mm, and the thickness is 1.2mm ; blockage factor (cross sectional tube area over the cross sectional area of the test section) is about 0.38. All of sensors and measurement systems (RTD, pressure sensor, flow-meter, relative humidity sensor, etc.) are calibrated with certificated standard sensors and the uncertainty for the heat transfer measurement is surveyed to have the uncertainty within 7%. As experimental results, overall heat transfer coefficient of the Teflon (FEP) coated tube is degraded about 20% compared to bare stainless tube. The degradation of overall heat transfer coefficient of Teflon coated tube comes from the additional heat transfer resistance due to Teflon coating. Its magnitude of heat transfer resistance is comparable to the in-tube heat transfer resistance. Nusselt and Sherwood numbers on Teflon (FEP) coated surface and bare stainless steel surface are discussed in detail with the contact angles of the condensate.

• Asian-Australasian Journal of Animal Sciences
• /
• 제28권2호
• /
• pp.252-259
• /
• 2015

The present study was conducted to investigate the efficacy of sweet potato powder (SPP) and water as a fat replacer in low-fat pork patties. Low-fat pork patties were developed by replacing the added fat with combinations of SPP and chilled water. Three different levels of SPP/chilled water viz. 0.5/9.5% (T-1), 1.0/9.0% (T-2), and 1.5/8.5% (T-3) were compared with a control containing 10% animal fat. The quality of low-fat pork patties was evaluated for physico-chemical (pH, emulsion stability, cooking yield, $a_w$), proximate, instrumental colour and textural profile, and sensory attributes. The cooking yield and emulsion stability improved (p<0.05) in all treatments over the control and were highest in T-2. Instrumental texture profile attributes and hardness decreased, whereas cohesiveness increased compared with control, irrespective of SPP level. Dimensional parameters (% gain in height and % decrease in diameter) were better maintained during cooking in the low-fat product than control. The sensory quality attributes juiciness, texture and overall acceptability of T-2 and T-3 were (p<0.05) higher than control. Results concluded that low-fat pork patties with acceptable sensory attributes, improved cooking yield and textural attributes can be successfully developed with the incorporation of a combination of 1.0% SPP and 9.0% chilled water.

• 한국산업보건학회지
• /
• 제5권2호
• /
• pp.172-183
• /
• 1995

The airborne concentrations of the welding fumes produced during $CO_2$ arcwelding process at shipbuilding, shiprepairing, container manufacturing and car accessary manufacturing industry were investigated. The effects how much reduced the welding fume were checked when the portable fan was used. The results were as follows; 1.The geometric mean of welding fume concentration in shipbuilding factory was $10.05mg/m^3$. This exposure concentration was higher than other 3 manufacturing industries at 95% confidence level. 2. The sampling filters for welding fume could be digested with acid within 1 hour by microwave oven. The recoveries for investigated metal elements were all over 95%. 3. The optimal wavelength could be selected for the simultaneous analysis of 8 metal elements by ICP(Inductively Coupled Plasma). 4. Noxious gases($O_1,NO_2$) produced during $CO_1$ gas arc welding process were detected that the concentration of ozone($O_1$) was less than 0.01 ppm and that of nitrogen dioxide($NO_2$) was 0.01-0.03 ppm. 5. The geometric mean of welding fume particle diameter was $1.26{\mu}m$ and geometric standard deviation was 1.51 for the counts when particle an analyzer(ELZONE) had been used. 6. When the portable fan had been used,the reduced percent of total welding fume for workers was about 47.8% when portable fan was applied to blow and 71.7% when to exhaust.

• Journal of Pharmaceutical Investigation
• /
• 제41권1호
• /
• pp.51-57
• /
• 2011

The objective of this study was to enhance the utilitization of Ibuprofen (IBU) by introducing the fast-disintegrating tablet (FDT) form. Presently, IBU is being widely used as a tablet or syrup form. But in contrast to these two formulations, IBU as FDT is not only convenient but also increases the control over the time release of the drug, noted by using Alginate beads. This study was carried out with Sodium Alginate and IBU at the ratios of 1:0, 1:0.5, 1:1, and 1:2 in order to produce a series of beads with different ratios. During the drying process of the beads, talc was added in beads to compare the effects with and without the talc. The final product was scanned with SEM imaging to determine the difference in the surface of the beads. The parameters assessed were the diameter, content assay, dissolution test and effectiveness of time-release. Direct compression method was used to prepare FDT containing IBU bead. The properties of FDT, such as hardness, disintegration time, were investigated. The dissolution profiles of FDT were tested using KP dissolution apparatus 1 (basket method). The results suggest addition of talc and drying the beads made the surface smooth and less vulnerable to clutter into chunks. The size of beads was less than 300 ${\mu}m$ which did not create a sandy feeling in the mouth. Thus, the beads formulation model made the sustained release of the drug possible, the hardness of FDT (1.25~1.50 $Kg/cm^2$) was acceptable and all the values of dissolving period were less than 30 seconds. The dissolution profile of FDT was same as that of IBU bead. The efficient dissolution profile and low price of IBU bead containing Sodium Alginate, the FDT formulation prepared from IBU bead can save the expenses and can improve the convenience of application of this drug.

• Journal of Chest Surgery
• /
• 제20권3호
• /
• pp.458-472
• /
• 1987

A heart supplies bloods of about 15, 000 liters to each human organ in a day. A normal function of heart valves is necessary to this act of heart. The disease of heart valve develops to a narrowness of a closure, resulting in an abnormal circulation of bloods. In an attempt to eliminate the affliction of heart valves, the operation method to repair with artificial heart valves has been developed and saved numerous patients over past 30 years. This replacement operation has been performed since early 1960`s in Korea, but all the artificial heart valves used are imported from abroad with very high costs until recent years. The artificial heart valve using pyrolytic carbon has been developed at KAIST, which was proved to be stable in the mechanical performance and durability. Therefore, the in viva performance of this valve was examined through animal tests. The artificial heart valves used in this study are tilting disc type valves, in which the disc were made of graphite coated with pyrolytic carbon and the cages were made of titanium. In viva testings of these valves were performed in 12 dogs, in which right ventriculo-pulmonary arterial [Croup I] or inter-aortic [Croup IV] valved conduit was implanted using polytetrafluoroethylene conduits containing KAIST valve and aortic valve [Group II] or pulmonary valve [Croup III] was replaced by a KAIST valve with a 21mm or 19mm tissue annulus diameter. In group I and II, pre-and post-operative transvalvular pressure gradient was measured and compared with other prosthetic valves. During post operative period laboratory examination was performed including hemoglobin, hematocrit, red cell count, white cell, lactic acid dehydrogenase and platelet. The eight surviving dogs were sacrificed and autopsy was performed at 2, 6, and 8 weeks. KAIST valve has low transvalvular gradient and relatively high orifice area. Average ventriculo-aortic peak systolic transvalvular gradient was 14 mmHg in 21 mm valve and 19 mmHg in 19 mm valve. The valve has slight intravascular hemolysis effect. Thrombogenic effect of low polishing quality and eddy currents around small orifice is high. The valve has vulnerability of disc movement. These animal tests suggest that the improvement of the heart valve design, surface polishing state and prescription methods.

• 대한수학회지
• /
• 제52권6호
• /
• pp.1323-1336
• /
• 2015

Let S be a semigroup with 0 and R be a ring with 1. We extend the definition of the zero-divisor graphs of commutative semigroups to not necessarily commutative semigroups. We define an annihilating-ideal graph of a ring as a special type of zero-divisor graph of a semigroup. We introduce two ways to define the zero-divisor graphs of semigroups. The first definition gives a directed graph ${\Gamma}$(S), and the other definition yields an undirected graph ${\overline{\Gamma}}$(S). It is shown that ${\Gamma}$(S) is not necessarily connected, but ${\overline{\Gamma}}$(S) is always connected and diam$({\overline{\Gamma}}(S)){\leq}3$. For a ring R define a directed graph ${\mathbb{APOG}}(R)$ to be equal to ${\Gamma}({\mathbb{IPO}}(R))$, where ${\mathbb{IPO}}(R)$ is a semigroup consisting of all products of two one-sided ideals of R, and define an undirected graph ${\overline{\mathbb{APOG}}}(R)$ to be equal to ${\overline{\Gamma}}({\mathbb{IPO}}(R))$. We show that R is an Artinian (resp., Noetherian) ring if and only if ${\mathbb{APOG}}(R)$ has DCC (resp., ACC) on some special subset of its vertices. Also, it is shown that ${\overline{\mathbb{APOG}}}(R)$ is a complete graph if and only if either $(D(R))^2=0,R$ is a direct product of two division rings, or R is a local ring with maximal ideal m such that ${\mathbb{IPO}}(R)=\{0,m,m^2,R\}$. Finally, we investigate the diameter and the girth of square matrix rings over commutative rings $M_{n{\times}n}(R)$ where $n{\geq} 2$.

• Nutrition Research and Practice
• /
• 제10권5호
• /
• pp.524-529
• /
• 2016

BACKGROUND/OBJECTIVES: Use of smaller plates to control food intake is a commonly recommended strategy for restricting energy intake, despite conflicting results. Therefore, the aim of this study was to examine whether or not three different sizes of plates influence energy intake during a multi-itemed buffet meal in normal weight women. SUBJECTS/METHODS: This was a cross-over study conducted on 37 female participants aged 19-25 years with normal BMI levels. Participants were recruited from Hacettepe University and the surrounding community. On experimental days, participants ate a standard breakfast and were then randomly assigned to eat lunch using a small (19 cm), medium (23 cm), or large (28 cm) diameter plate. Visual analogue scale (VAS) scores on sensory and satiety outcomes were measured for all meals. Energy and macronutrient intakes during lunch were recorded. RESULTS: There was no evidence that use of a smaller plate size reduced energy or specific macronutrient intake during the free choice lunch meal. Multiple visits to the serving table were not associated with energy or macronutrient intake. Plate size did not affect VAS scores during the test days. CONCLUSIONS: Plate size did not influence energy intake, meal composition, or palatability in normal weight women during a multi-itemed open buffet lunch. Studies in natural settings at the population level are needed to clarify current outcomes.

• 한국환경복원기술학회지
• /
• 제20권2호
• /
• pp.1-12
• /
• 2017

This study aims to provide the basic habitat data for the alternative breeding sites of Family Ardeidae including Ardea cinerea, Egretta alba modesta, Egretta intermedia, Egretta garzetta, Bubulcus ibis and Nycticorax nyciticorax. Species numbers, flight directions for detecting foraging grounds and current vegetation structure were investigated nesting at Gunsan urban forest area. Data were collected over a period of 10 weeks, from 15 June - 31 August 2014. The total nest and population of Family Ardeida were 684 and 1,712 respectively. Percentage of birds observed flying in 8 major compass directions were as follows. 57.27% of all birds were observed flying northwest, 22.09% were observed flying south and 13.40% were flying north. For possible foraging areas, to the northwest, there are Geumgang river tidal flats, and to the south, paddy fields and streams within 2km. Flying directions by species (${\chi}^2=287.18$, P<.001, Cramer's V=0.12) and by seasons(${\chi}^2=839.94$, P<.001, Cramer's V=0.19) showed significant difference statistically. In relation between species and directions, 60.31% and 24.05% of Bubulcus ibis and 59.40% and 23.00% of Ardea cinerea were observed flying northwest and south respectively. Vegetation in the sites consist of an overstory of 3 to 7 species. At site 1, Pinus thunbergii was the dominant species and site 2, Chamaecyparis obtusa. Understory vegetation is composed of shrubs, saplings and small trees of Chamaecyparis obtusa, Quercus acutissima, Smilax china and Platycarya strobilacea. Egrets and herons usually nested at the dense population and canopy overlayed forest, and especially branches and leaves of smallwood with less than 10cm of breast height diameter were relatively severely damaged due to the nesting and excreta.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.649-652
• /
• 2011

산화제 유동 변화를 위한 디스크를 예혼합실에 장착하여, 디스크의 직경과 길이를 변경하며 PMMA/GOx를 이용한 하이브리드 로켓 모터의 지상연소시험을 수행하였다. 디스크에 의해 산화제 유동의 와류유출(vortex shedding)이 발생하여, 연소율과 압력 진동 등의 연소 특성이 변화하였다. 연소실험 후 PMMA를 축방향으로 잘라내어 연소면을 관찰하여, PMMA의 연소면 전체에서 딤플 형태의 패턴이 발견하었다. 이는 연소 과정 중 연소면 근처에서 발생하는 blowing 효과에 의해 변화된 산화제 유동의 경계층 특성에 기인한 것으로 보이며, LES 기법을 이용하여 수행한 수치적 연구 결과와 일치한다. 이는 하이브리드 로켓 모터의 연소불안정 현상을 이해하는데 중요한 자료로 판단된다.

• 한국미생물·생명공학회지
• /
• 제30권2호
• /
• pp.111-115
• /
• 2002

천연 황색소 생산을 위하여 Monascus anka Nakazawa et Sato IFO 4478(KCCM l1832 strain) 균주를 모균주로 하여 UV 조사 및 NTG(N-methyl-N'-nitro-N-nitrosoguanidine)처리 및 이들 방법을 병용하는 방법을 사용하여 모균주와는 색소생성 특성이 다르게 황색소를 단일성분으로 생성하는 변이주를 분리하고 그 특성을 조사하였다. leucine, cystein, aspartic acid, glutamic acid 와 asparagine 등 5종의 아미노산에 대한 영양요구주를 분리하였고 이중 asparagine 영양요구주 Y7은 colony 형태와 균사의 직경에서 약간의 차이를 나타내지만 전형적인 Monascus 균주의 특성을 지니고 있었으며 특히 유성생식에 의한 번식 특성이 강하여 색소 생성에 유리한 조건을 지니고 있었다. 그리고 Y7은 밝은 색조의 황색소를 단일 성분으로 생성하며 10대 이상의 계대배양에서도 색소 생성 특성이 안정하였고 색소 생성량이 모균주보다 약 2.2배 높은 값을 나타내고 있었다. 이때 생성된 황색소는 373 nm에서 단일 흡수 peak를 나타내고 물, 에탄올 등 극성용매에 대한 용해성이 높은 특성을 나타내며 생성된 색소의 대부분이 균체 밖으로 배출되는 특성을 지니고 있었다.