• 한국안전학회지
• /
• 제20권4호
• /
• pp.46-53
• /
• 2005

Existing study far fire-resistant concrete has been done already. but it is not found out how the waste tyre mixing concrete will be acted against fire. This waste tyre concrete molds under the condition of $0^{\circ}C,\;200^{\circ}C,\;400^{\circ}C,\;600^{\circ}C$ were heated in gas oven. It was worried about that they might be fractured down at about $800^{\circ}C$ so that they can not be tested. compressive strength for the test molds are made with commercially used $180kg/cm^2,\;210kg/cm^2,\;240kg/cm^2,\;270kg/cm^2$ mixing saw dust with proportion such as 0.05%, 0.1%, 0.2%, 0.4%, 0.6%, 0.8%, 1.0%, 1.2%, 1.4%, 1.6%, 1.8%, 2.0% compressive strength at $200^{\circ}C$ was approximately 20% from the original, while approximately 30% deoreased at $400^{\circ}C$. their results are not quite different from the normal concrete condition even though they contains saw dust in it. The higher strength the concrete has, the less strength was decreased. There are almost no difference in strength under the condition of less than $400^{\circ}C$, but damage of concrete structure could be considerable large with more than $400^{\circ}C$.

• 대한건축학회논문집:구조계
• /
• 제34권7호
• /
• pp.19-26
• /
• 2018

This study tested 25 lightweight aggregate concrete (LWAC) mixtures using the expanded bottom ash and dredged soil granules to examine the compressive strength gain of such concrete with different ages. The test parameters investigated were water-to-cement ratios and the natural sand content for the replacement of lightweight fine aggregate. The compressive strength gain rate in the basic equation specified in fib model code was experimentally determined in each mixture and then empirically formulated as a function of the water-to-cement ratio and oven-dried density of concrete. When compared with 28-day compressive strength, the tested LWAC mixtures exhibited relatively low gain ratios (0.49~0.82) at an age of 3 days whereas the gain ratios (1.16~1.41) at 91 days were higher than that (1.05~1.15) of the conventional normal-weight concrete. Thus, the fib model equations tend to overestimate the early strength gain of LWAC but underestimate the long-term strength gain. The proposed equations are in good agreement with the measured compressive strength development of LWAC at different ages, indicating that the mean and standard deviation of the normalized root mean square errors determined in each mixture are 0.101 and 0.053, respectively.

• 한국산학기술학회논문지
• /
• 제22권2호
• /
• pp.26-32
• /
• 2021

카본 전극 페로브스카이트 태양전지의 광활성층을 형성하는데 열판, 오븐, 쾌속열처리로 방법을 달리하며 이때 광전기적 특성과 미세구조 변화를 확인하였다. Glass/FTO/compact TiO2/meso TiO2/meso ZrO2/perovskite/carbon electrode 구조의 페로브스카이트 태양전지 소자를 열판 공정, 오븐 공정, RTA(rapid thermal annealing) 공정을 이용하여 준비하였다. 이때 광전기적 특성과 미세구조를 solar simulator와 광학현미경, 장발산주사전자현미경을 이용하여 각 소자의 특성을 분석하였다. 광전기적 특성 분석 결과, RTA 공정을 이용하여 제작한 소자에서 가장 우수한 광전기적 특성을 확인할 수 있었다. 미세구조 분석 결과 열판 공정과 오븐 공정으로 제작한 시편은 카본 전극 상부에 과잉 페로브스카이트 상이 형성되고, RTA 공정으로 제작한 시편에서는 시편 상부에 과잉 페로브스카이트 상 없이, 균일한 페로브스카이트가 형성된 것을 확인할 수 있었다. 또한 단면 미세구조에서는 RTA 공정으로 제작한 소자가 다공성 카본 전극 층에 고밀도의 페로브스카이트 층을 형성하여 우수한 광전기적 특성을 나타내었다. 따라서 대면적 소자 제작의 공정시간을 고려한 새로운 열처리방안으로 RTA 방법의 채용 가능성을 확인하였다.

• 한국식품조리과학회지
• /
• 제20권6호
• /
• pp.643-649
• /
• 2004

돼지고기를 전기그릴($EG;\;260^{\circ}C$, 5분) 및 전자렌지(MW, 6분)를 이용하여 조리 한 후 일정기간 냉장(0-14일), 냉동(0-90일) 보존한 시료와 이를 MW(1 min)로 재가열한 시료의 변이원성, 지질과 산화도(TBA), 및 육조직(SEM)을 연구하였다. S9 mix를 첨가하지 않은 상태에서 냉장 및 냉동 저장 기간에 따른 변이원성 유발 정도는 저장 기간이 증가함에 따라 변이원성이 증가하였고, 대사활성물질을 첨가했을 때 더 높은 변이원성을 나타내어 간접변이원이 더 많이 존재함을 확인하였으며, MW 재가열 처리 시는 더 높은 변이원성을 나타내었다. MW(6 min)로 조리했을 때 EG로 조리한 것보다 변이원 유발 가능성 면에서 보다 안전하다고 할수 있으나 냉동저장하고 재가열시는 변이원성 유발 가능성이 보다 높다고 사료된다. 변이원성과 과산화지질 생성간의 상관관계는 대사활성물질을 첨가하지 않았을 때 냉장 저장시 r=0.85, 냉동 저장 시 r=0.86이었고, MW 재가열하였을 때 냉장 저장 시 r=0.98, 냉동 저장 시 r=0.83으로 냉장 저장이 더 높은 상관관계를 나타내었다. SEM을 이용하여 육조직을 관찰한 결과 MW로 조리한 시료 및 MW로 재가열한 시료에서 더 많은 수증기 통로가 관찰되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.1113-1115
• /
• 2002

Mesoporous silica, MCM-41, was synthesized by sol-gel method. The organic structure-directing agent must be removed to make the desired proes. To achieve this, alternative calcination method using microwave oven was adapted to this removal stage. Microwave calcination was shown to provide a novel, rapid and inexpensive method of praparing nanoporous material. It was studied how the porous structure, surface area and pore size distribution were changes under microwave calcination.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.293-296
• /
• 2002

Surface relief holograms are fabricated by means of irradiation of laser interference patterns. The diffraction efficiency and the surface relief depth depend on the writing energy and the polarization of the writing laser beam. This structure is very stable at temperatures under glass transition temperature $T_g$ and can be erased by heating above $T_g$. We proposed a new technique to control the surface relief structure. The electric charge was deposited on the surface relief grating in a corona-depositing poling setup in an oven. The first-order diffraction efficiency measured before and after corona discharge increased from about 0.24 % to about 28 %. This diffraction efficiency increase is mainly caused by the increase of the relief depth caused by the electric charge. The relief depth is increased from 20 nm to 350 nm by corona charging. .

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.251-252
• /
• 2008

In this study, we have investigated electrical properties of semiconductive materials for power cable caused by copper tape shield structure. Volume resistivity of specimens was measured by volume resistivity meter after 10 minutes in the pre-heated oven of both 23 [$^{\circ}C$] and 90 [$^{\circ}C$]. From this experimental results, the volume resistivity had different properties because of PTC/NTC tendency at between 23 [$^{\circ}C$] and 90 [$^{\circ}C$].

• 한국산업융합학회 논문집
• /
• 제2권2호
• /
• pp.61-68
• /
• 1999

The variety of crystalline structure and mechanical properties of PP filament treated with dry heat treatment at different draw ratio has been studied. Crystalline structure and mechanical properties of annealed PP filament at different draw ratio has been examined by XRD, UTM, and density method. Heat treatment has been carried out $100^{\circ}C$, $120^{\circ}C$ $140^{\circ}C$ for 30min. in dry oven. From the results of this study, it found the following facts. It was found that the crystallinity and crystallite size of (110) plane of sample were increased with increasing of annealed temperature and draw ratio. The crystalline form of annealed sample which was undrawn showed ${\alpha}$, ${\beta}$ mixing form below $120^{\circ}C$ and showed ${\alpha}$ form at $140^{\circ}C$. But the crystalline form of annealed sample which was drawn showed ${\alpha}$ form at $120^{\circ}C$. Initial modulus and tensile strength were increased with increasing of annealing temperature, and the degree of orientation was decreased with decreasing of annealing temperature.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.835-837
• /
• 2017

본 연구에서는 필라멘트 와인딩을 이용한 원통형 복합재 격자구조체의 제작 공정을 서술하였다. 원통형 복합재 격자구조체는 크게 네 단계의 제작 공정을 통해 제작된다. 격자 형상을 갖는 실리콘 금형을 맨드릴에 설치하고 연속 섬유를 실리콘 금형 위에 와인딩 한다. 섬유의 와인딩 후 모든 영역에서 동일한 두께를 갖도록 섬유 교차부의 압착 공정을 수행한다. 마지막으로 복합재 격자구조체를 오븐에서 경화하고 금형을 탈형한다. 제작된 제품의 치수는 설계 사양과 비교하여 2.4%의 오차가 발생하는 것을 확인하였다.

• 한국산업융합학회 논문집
• /
• 제3권4호
• /
• pp.345-351
• /
• 2000

The change of crystalline structure of drawn PP filaments were investigated. Samples were treated by isothermally annealed after elevated heating from $20^{\circ}C$. Measurements were carried out with XRD for crystallite size and density gradient tube for crystallinity. Isothermally heat treatment were carried out at the temperature of $100^{\circ}C$, $120^{\circ}C$ and $140^{\circ}C$ for 10min., 30min. and 60min. in dry oven. The isothermal heat treatment after elevated heating from $20^{\circ}C$ were carried out at the temperature of $100^{\circ}C$, $120^{\circ}C$ and $140^{\circ}C$ for 10min., 30min. and 60min. with heating rate of $1^{\circ}C$/min., $5^{\circ}C$/min. and $10^{\circ}C$/min. From the results of this study, it found the following facts. It was found that the crystallinity and crystallite size of (110) plane of sample were increased with increasing of annealed temperature and time. Also crystallinity and crystallite size of samples which were isothermally annealed after elevated heating from $20^{\circ}C$ were higher than those of isohtermally annealed samples.