• The Journal of the Acoustical Society of Korea
• /
• v.17 no.3E
• /
• pp.53-57
• /
• 1998

Spectral information at a speech coder should be quantized with sufficient accuracy to keep perceptually transparent output speech. Spectral information at a low bit rate speech coder is usually transformed into corresponding line spectrum pair parameters and is often quantized with a vector quantization algorithm. As the vector quantization algorithm generally has high complexity in the optimal code vector searching routine, the complexity reduction in that routine is investigated using the ordering property of the line spectrum pair. When the proposed complexity reduction algorithm is applied to the well-known split vector quantization algorithm, the 46% complexity reduction is achieved in the distortion measure compu-tation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.7
• /
• pp.1574-1578
• /
• 1997

In this paper, some problems that occur from faulty elements in a direction finding system composed of the linear array are studied and the method which improves the performance is proposed. The faulty element means the sensor that has no output or highly reduced gain than other normal sensors. In the presence method, the ocrrecting vector is calculated by maximizing the spatial spectrum subject to a constraint. The compensated spatial spectrum is obtained by this vector. The computer simulations have been performance to study the performance of the proposed method.

• Current Optics and Photonics
• /
• v.2 no.5
• /
• pp.443-447
• /
• 2018

We propose a diode-pumped cesium laser using frequency locking of a pump laser that can effectively increase the maximum output power of the cesium laser. We simultaneously monitored the absorption spectrum of cesium and the laser output power, and the frequency of pump laser was locked at the center of the $D_2$ absorption line of the cesium atom to obtain an effective gain enhancement. Using this scheme, we have achieved output power increase of ~0.1 W compared to when frequency locking was not applied. Furthermore, by optimizing the temperature of the cesium cell and the reflectivity of the output coupler, we successfully achieved an output power of 1.4 W using the pump power of 2.9 W, providing a slope efficiency of 61.5% and optical-to-optical efficiency of 49%.

• Korean Journal of Optics and Photonics
• /
• v.5 no.2
• /
• pp.266-271
• /
• 1994

The output power and the energy of Rh-6G dye laser were enhanced by the mixture of Rh-560 dye whose fluorescence spectrum was coincident with the absorption spectrum of Rh-6G. The argon filled coaxial flashlamp used for pulsed pumping and argon laser for CW pumping. The concentration of Rh-6G dye was optimized in each pumping method before Rh-560 dye was mixed in Rh-6G dye solution. In the coaxial flash lamp pumped Rh-6G laser the output energy was increased about 30% when Rh-560 was mixed at 1% of Rh-6G concentration. In the case of argon laser pumping with multiline, the output power was increased 18% at the concentration of 2.5%. In the single line laser pumping, the output power was enhanced more efficiently. The power enhancements were 72% and 88% when the pumping wavelengths were 488 nm and 514.5 nm respectively. ively.

• Journal of the Optical Society of Korea
• /
• v.7 no.4
• /
• pp.258-263
• /
• 2003

Simple algebraic expressions are derived to approximate the optimal input RMS pulse width and the resulting output RMS pulse width in single-mode fibers. The results are compared with the previously published methods and with numerical results by the split-step Fourier method. In addition, for a transform-limited Gaussian input pulse, it is shown that there is no optimum input pulse width to minimize the output spectrum width. Finally, with fiber nonlinearity, it is shown mathematically that there is not an optimum input pulse width to minimize the product,${\sigma}_t{\sigma}_{\omega}$, which is inversely proportional to the transmission capacity of WDM systems.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.5
• /
• pp.152-161
• /
• 2017

The CBTC(Communication based Train Control) system employed on 2.4GHz ISM band adopt the IEEE802.11.x standard. Therefor communication time delay, distortion and data losses will be produced. To overcome these problems, CPSK(Continuous Phase shift keying) modulated DS/SS(Direct Sequence Spread Spectrum) transmitter with 908MHz carrier frequency is proposed. Through the eye diagram and scatter diagram the performance is analysed. And the phase noise characteristic of the local oscillator is measured about 60dBc/Hz, this means that the phase noise performance is very good compared to the signal. Reference frequency suppression of the 2nd local oscillator is 50dB below compared to the signal. Through the polarities of the complementary signal equally probable, the line spectrum of the output spectrum is eliminated. The nonlinear effects which introduce the spectral spreading or spectral regeneration is reduced remarkably.

• The Journal of the Korea Contents Association
• /
• v.18 no.11
• /
• pp.430-446
• /
• 2018

In this paper, we conducted a comparative study on the methodology for impact analysis as the economic grounds for formulating policy and investment plan concerned with utilizing spectrum resource. In order to provide numerical results for objective comparison and selection among policy and investment planning, methods to be analyzed are focused on quantitative methodology based on mathematical models, consequently the utility and limits of econometric model, input-output analysis, computable general equilibrium and system dynamics are compared from various viewpoints including analysis cost. Besides, we compared the methodologies in the standpoint of utilizing spectrum and discussed the recent findings of mixed models combining multiple methodologies to exploit the advantages of each methodology and to offset the limit. Results of the research can be used as reference indicators to select the method that conforms to the purpose and priority of analysis verifying the efficiency of execution of policies and investment plans.

• Progress in Medical Physics
• /
• v.11 no.2
• /
• pp.141-146
• /
• 2000

Power spectrum analysis is a powerful noninvasive tool for quantifying autonomic nervous system activity. In this paper, We developed a measuring system for Autonomic Nervous Activity by using power spectrum analysis method to obtain the activities of autonomic nervous system. This system adopt a isolated power for patient's safety. In this system, Two output signal is obtained - R-R interval time variability and Respiration time variability. Time variability is use to find out some disease related to Autonomic Nervous System. Experimental tested range is 30 ～ 240 BPM for ECG and 15～80 BPM for Respiration.

• Journal of Biosystems Engineering
• /
• v.33 no.1
• /
• pp.63-68
• /
• 2008

This study was carried out to find a useful method to predict hardness of tomato using optical spectrum data. Optical spectrum of reflectance and transmittance data were collected processed by 9 kind of preprocessing methods-normalizations of mean, maximum and range, SNV (standard normal variate), MSC (multiplicative scatter correction), the first derivative and second derivative of Savitzky-Golay and Norris-Gap. With the preprocessed and non-processed original spectrum data, prediction models of hardness of tomato were developed using analytical tools of PLS (partial least squares) and MLR (multiple linear regression) and tested for their validation. The test of validation resulted that the analytical tools of PLS and MLR output similar performances while the transmittance spectra showed much better result than the reflectance spectra.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.5
• /
• pp.7-12
• /
• 2005

This paper presents several time series methods to analyze the chatter mechanics by using the power spectrum of these algorithms considering the cutting dynamics. In this study, several time series models such as AR(burg, forwardbackward, geometric lattice, instrument variable, least square, Yule Walker), ARX(1s, iv4), ARMAX, ARMA, Box Jenkins, Output Error were modeled and compared with one another. Finally, it was proven that time series modelings are also a desirable and reliable algorithm than the other conventional methods(FFT) for the calculation of the chatter mode in turning operation. Also, the spectrum of times series methods is a little bit more powerful than the FFT fer the detection of a high noisy and weak chatter mode. The radial cutting force Fy has been used for spectrum and chatter stability lobe analysis in this study.