• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.60-73
• /
• 2008

In this paper a three-phase ac-to-dc resonant converter with high input power factor and isolated output is proposed. To improve the input power factor of the converter, high frequency current is injected into the input of the three-phase diode bridge rectifier. It is injected through an impedance network consisting of a series of L-C branches from the output of the high frequency three-phase inverter. A narrow switching frequency variation is required to regulate the output voltage. A design example with different design curves is illustrated along with the component ratings. Experimental verification of the converter is performed on a prototype of 3 kW, 1000 V output, operating above 300 kHz. Experimental results confirm the concept of the proposed converter. Narrow switching frequency variation is required to regulate the output voltage.

• 산업기술연구
• /
• 제25권B호
• /
• pp.195-202
• /
• 2005

The rectifier characteristics and the quality of the input current worsens with the increase of unbalances or harmonics of the supply voltages. Rectifier input current harmonics interfere with proper power system operation, reduce rectifier power factor, and limit the power available from a given source. It is of importance to select appropriately the rectifier's output filter inductance to determine the rectifier input current waveform, the input current harmonics, and the power factor. This paper presents a quantitative analysis of single and three phase rectifier input current harmonics, total harmonic distortion, and power factor as a function of the output filter inductance under balanced and unbalanced conditions. Also, its performance under the supply voltage including harmonics be investigated. These results provide a reference for selecting reasonable rectifier's output filter inductance for given harmonics or power factor criterion.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.290-293
• /
• 2000

In this paper the algorithm which controls output voltage and power factor independently and the algorithm which controls output voltage with fixed unity power factor are compared and analyzed. These algorithms are applied to single-phase AC/DC parallel are applied to single-phase AC/DC parallel converters for a high speed train system. The control characteristic of the algorithms are compared and analyzed with respect to the output voltage and input power factor when system parameters vary.

• 한국방사선학회논문지
• /
• 제14권3호
• /
• pp.289-294
• /
• 2020

X-선영상의 품질과 환자의 피폭 관리를 위하여 X-선장치에서 출력되는 선량(공기 흡수선량(mGy)은 측정으로부터 자료화 하는 것이 필요하다. 이 연구의 목적은 X-선장치의 출력선량과 출력인자(Of)의 측정으로부터 출력선량을 계산할 수 있는 식을 구하는데 있다. X-선장치로부터 조사되는 X-빔의 출력선량과 출력인자는 XR멀티검출기를 사용하여 측정하였다. 결과로서, 관전류-조사시간 곱(mAs)으로 나누어진 측정된 출력선량과 설정관전압을 Allometric1 fit하여 출력선량 계산식을 얻었다. 이 식에 출력인자를 곱하여 최종 출력선량 계산식을 구하였다. 구하여진 최종 출력선량 계산식은 모든 관전압, 관전류, 조사시간, 조사야 그리고 거리에 적용하는데 유용할 것으로 사료된다.

• Journal of Power Electronics
• /
• 제4권1호
• /
• pp.18-27
• /
• 2004

The output storage capacitor of the PFC converters is commonly designed for the selected hold-up time or the allowed output ripple voltage percentage. Nevertheless, this output capacitor is a main contribution factor to the PFC system stability. Moreover, seeking for a minimum output storage capacitor that assures the PFC desired operation under all condition, and providing the advantage of a small size and low cost is the main interesting target for engineering. Therefore, in this issue the design steps of the PFC converter have been discussed depending on three choices, output ripple, hold-up time, and stability. It is cleared that any design must take the minimum required storage capacitor for stability prospective as step-l in deign, then apply for any other specification like hold-up time or ripple percentage.

• 토지주택연구
• /
• 제9권4호
• /
• pp.33-42
• /
• 2018

As a radiant heating panel gets more popularity, the need to study on evaluation method of thermal output of the panel also becomes increasing. Generally, the chamber using method is applied to evaluate the thermal output through an experiment. However, the chamber using method cannot be used due to the limitations on space and cost. EN1264 addresses the test equipment to evaluate the thermal output by using simpler experimental setup, and introduces application method in detail. However, there is not enough description of control methods to meet the experiment condition, and it is difficult to meet this when practical experiment. Therefore, this paper analysed the control error factors of when the thermal output experiment is performed. When EN1264 method is applied to evaluate the thermal output of the radiant floor heating panel, the error factor which is caused by the characteristic of test equipment cannot be removed by the control methods of chamber using method. In addition, the error factor can be occurred at the element which is located out of the control system. These possible error factors are defined as the characteristic error factors.

• 대한방사선치료학회지
• /
• 제25권2호
• /
• pp.107-113
• /
• 2013

목 적: 호흡동조 시스템을 이용한 양성자치료 시 생성되는 양성자빔을 측정하고 분석함으로써 호흡동조 양성자치료의 정확성을 검증하고자 한다. 대상 및 방법: 호흡동조 양성자치료를 실시한 환자 세 명의 치료계획을 이용하여 양성자 치료 시스템에서 양성자빔을 생성했다. 이때 자체 제작한 구동 팬톰을 사용하여 호흡동조 시스템을 적용해 분할 조사되는 양성자빔을 재현하였다. 양성자빔의 중요특성인 Range, Spread-Out Bragg Peak (SOBP), Output factor를 각 5회씩 측정하였으며 호흡동조 시스템을 적용하지 않은 연속 양성자빔에서도 동일한 항목들을 측정했다. Range와 SOBP 측정에는 Multi-Layer Ionization Chamber, Output factor 측정에는 Scanditronix Wellhofer와 Farmer chamber를 사용했다. 결 과: 호흡동조 시스템을 적용한 경우 세 환자의 평균 Range는 7.226, 12.216, 19.918 $g/cm^2$, SOBP는 4.950, 6.496, 8.486 $g/cm^2$, Output factor는 0.985, 1.026, 1.138 cGy/MU였으며, 적용하지 않은 경우 평균 Range는 7.230, 12.220, 19.920 $g/cm^2$, SOBP는 4.940, 6.512, 8.490 $g/cm^2$, Output factor는 0.984, 1.027, 1.136 cGy/MU로 측정됐다. 평균 Range의 차는 -0.004, -0.004, -0.002 $g/cm^2$, SOBP는 0.010, -0.016, -0.004 $g/cm^2$, Output factor는 0.001, -0.001, 0.002 cGy/MU로 나타났다. 결 론: 호흡동조 양성자치료 시 분할 조사된 양성자빔과 연속 조사된 양성자빔의 Range, SOBP 및 Output factor 모두 차이가 미미했다. 따라서 본 연구를 통해 호흡동조 시 발생된 양성자빔의 선질을 검증하였고 이를 이용한 양성자치료의 정확성 또한 확인할 수 있었다.

• Journal of Power Electronics
• /
• 제19권6호
• /
• pp.1380-1392
• /
• 2019

Input filters are very important to matrix converters (MCs). They are used to improve grid side current waveform quality and to reduce the input voltage distortion supplied to the grid side. Due to the effects of the input filter and the output power, the grid side power factor (PF) is not at unity when the input power factor angle is zero. In this paper, the displacement angle between the grid side phase current and the phase voltage affected by the input filter parameters and output power is analyzed. Based on this, a new grid side PF unity compensation method implemented in the indirect space vector pulse width modulation (ISVPWM) method is presented, which has a larger compensation angle than the traditional compensation method, showing a higher grid side PF at unity in a wide output power range. Simulation and experimental results verify that the analysis of the displacement angle between the grid side phase current and the phase voltage affected by the input filter and output power is right and that the proposed compensation method has a better grid side PF at unity.

• Journal of Power Electronics
• /
• 제12권1호
• /
• pp.88-97
• /
• 2012

This paper presents a method for the digital control of a high power factor AC/DC converter employing the power balance control technique to achieve a fast response of the output voltage control. To avoid the effects of an output voltage ripple in the voltage control loop, the average output voltage is sampled and used as a feedback signal for the output voltage controller. The proposed control technique was verified by simulations using MATLAB/Simulink and its implementation was realized by a dsPIC30F4011 digital signal processor to control a CUK topology AC/DC converter with a 48V output voltage and a 250 W output power. The experimental results agree with the simulation results. The proposed control technique achieves a fast transient response with a lower line current distortion than is achieved when using a conventional proportional-integral controller and the power balance control technique with the conventional sampling method.

• Radiation Oncology Journal
• /
• 제4권2호
• /
• pp.165-172
• /
• 1986

전자선 치료시에 납판이나 저융점 합금이 조사면의 형태의 변형을 위하여 사용되고 있다. 콜리메이팅 장치와 마찬가지로 조사면 변형을 위한 물질도 전자선의 출력에 영향을 미친다. 저자들은 폴리스티렌 팬톰에 삽입된 Farmer형 전리함을 이용하여 Clinac-18의 전자선의 변형된 조사면에 대한 출력율을 측정하고 출력율에 영향을 미치는 요인들에 관해 분석했다. 전자선의 출력율은 전자선의 초기 에너지, 콜리메이팅 장치뿐만 아니라 조사면 크기에도 좌우되었다. 변형된 조사면에 대하여 잔자선의 에너지에 관계없이 X-선 콜리메이터와 전자선 어플리케이터의 조합이 고정되면 조사면의 크기 대 출력율은 A/P로 표시된 등가조사면의 크기에 따라 변하지만 조사면의 형태에 대해서는 무시할 수 있었다. 그러나 개조사면에 대한 출력율은 변형조사면의 출력율로부터 예상될 수 없고, 그것들만의 독립적인 관계를 가지고 있었다. 어플리케이터와 콜리메이터의 조합이 고정된 경우에 한해서 판자선의 변형조사면에 대한 출력율은 A/P로서 표시된 등가 조사면 방법에 의하여 구할 수 있다.