• 대한기계학회논문집A
• /
• 제26권12호
• /
• pp.2590-2597
• /
• 2002

A new torque measuring apparatus adopting the basic principle of a capacitive type sensor is proposed in this article. Two plate electrodes are working as a capacitive sensor, whose capacitance varies as torque is applied. One end of each plate is connected to the torque carrying shaft. Output characteristics of the torque sensor were theoretically analyzed and its validity was investigated through experiment. Calculations and calibration experiments show that the output is nonlinear, that is, the sensitivity is very high at low torque but decreases as torque increases. The sensitivity of the proposed system is about 100 times roughly higher than that of a conventional 4-strain gauge type torque sensor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.273-275
• /
• 2006

In this paper, we introduce a new design of fuzzy neural networks using input-output data information of target system. The proposed fuzzy neural networks is constructed by input-output data information and used the center of data distance by HCM clustering to obtain the characteristics of data. A membership function is defined by HCM clustering and is applied input-output dat included each rule to conclusion polynomial functions. We use triangular membership functions and simplified fuzzy inference, linear fuzzy inference, and modified quadratic fuzzy inference in conclusion. In the networks learning, back propagation algorithm of network is used to update the parameters of the network. The proposed model is evaluated with benchmark data.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.431-435
• /
• 1998

This paper deals with the output characteristics of resonant PWM inverter type X-ray generators connected to different DC power units i.e. a single phase full bridge rectifier, a three phase full bridge rectifier and a power storage unit(PSU). The quality of X-ray beam depend on the pulsation waveforms of DC voltage supplied to the X-ray tulbe. In a X-ray generator, the waveforme of DC output voltage can be affected from hramonic distortion of DC input power. When a tube voltage waveform is distorded, the property of X-ray beam such as reproducibility, direcibility and doesage can be reduced. Therefore, we compared DC output waveforms and doesages with three thpe of DC power units and show the experimental results in this paper

• Journal of Power Electronics
• /
• 제17권5호
• /
• pp.1278-1287
• /
• 2017

Inverters are widely used in distributed power generation and other applications. However, their lack of inertia and variable impedance may cause system instability and power transfer inaccuracy. This paper proposes a control scheme for a single phase voltage-controlled inverter with some grid-friendly characteristics. The proposed control algorithm enables the inverter to function as a voltage source with an inner output impedance in both the islanded and grid-connected modes. Virtual inertia and rotor equations are embedded in the PLL part. Thus, the frequency stability can remain. The inner output impedance can be adjusted freely, which helps to accurately decouple and transmit the output active and reactive power. The proposed inverter operates like a traditional synchronous generator. Simulations and experiments are designed and carried out to verify the proposed control strategy.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 전력전자학술대회
• /
• pp.7-11
• /
• 2017

This paper describes a design concept of NPC1 power stack for 1500VDC megawatt level solar inverter. This stack uses three latest half-bridge IGBT modules with highest power density and operation junction temperature, which enable realization of power level beyond 1MW without paralleling. Critical design concept on loop inductance is explained. Dynamic characteristics are verified by double-pulse test. Thermal characteristics and output power limits are verified by thermal test. Temperature-sensitive component on PCB as output power constraint is identified. Different PCB repositioning solutions are tested to give the overall output power thermal derating curves, which enable output power of 1.15MW at $T_A=55^{\circ}C$ with $15^{\circ}C$ thermal margin. The power stack characteristic and performance change under different thermal environment is further analyzed.

• 조명전기설비학회논문지
• /
• 제26권6호
• /
• pp.16-28
• /
• 2012

This paper proposes a quasi Z-source converter(QZSC) with a diode-capacitor output filter to improve the output DC voltage boost ability. The proposed converter has the same quasi Z-source network topology compared with the conventional converter. But the proposed method is adopted a diode-capacitor filter as its output filter, since the conventional method is used an inductor-capacitor as its output filter. Under the condition of the same input-output DC voltage, the proposed method has more lower shoot-through duty ratio than the conventional method. Also, because the proposed converter has same voltage boost factor under lower shoot-through duty ratio compared with the conventional converter, the proposed converter can be operated with the lower capacitor voltage of Z-source network and the lower input current. To confirm the validity of the proposed method, PSIM simulation and a DSP based experiment were performed to acquire the output DC voltage 120[V] under the input DC voltage 80[V]. And the capacitor voltage and inductor current in Z-source network, the output voltage of each converter were compared and discussed.

• 한국광학회지
• /
• 제7권3호
• /
• pp.244-249
• /
• 1996

DIAL의 레이저광원으로 사용하는 다중통과 Ti:sapphire의 증폭시스템을 각-다중방식으로 개발하고 출력에너지와 스펙트럼 특성을 조사하였다. 개발된 2단의 다중통과 증폭기의 특성은 790nm파장에서 최대 출력에너지는 22mJ, 증폭이득은 20dB, 펌핑에너지에 대한 출력효율은 18%이다. 또한 스펙트럼선폭은 파장가변 범위 705-845nm에서 0.15$cm^{-1}$ /(9.3pm)이다. 최대 출력에너지 때 레이저빔 발산각은 X, Y축에서 각각 1.1, 1.5mrad이며 레이저빔의 quality factir N$^{2}$은 2.6이다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(1)
• /
• pp.113-116
• /
• 2004

Output power of a photovoltaic system changes continuously as it strongly depends on the weather condition(isolation and temperature). Therefore, it is necessary the theoretical model realizes the electrical output characteristics of solar cell. Of several theoretical models for real solar cell, both parametric model and interpolation model are used widely. In this paper, we have propose a improved model of solar cell using its output characteristics that can be extended to calculate the rear solar cell characteristics at various temperatures and insolation. And more, the theoretical research of several models of solar cell using simulation analysis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.270-273
• /
• 1996

This paper describes a type of piezoelectric transformer with improved design principles. It consists of a thin rectangular piezoelectric ceramic plate having two input electrodes and one output electrode. The length of each input and output electrode is nearly one third of that of piezoelectric transformer itself. In the driving section, the ceramic plate is poled in the thickness direction reversely with each other, and has electrodes on both main faces. The electric input near its fundamental resonance frequency is applied to the driving section in parallel and the output voltage from the generating section is connected to the resistor load. Its equivalent circuit is derived from the Mason\`s model. The frequency characteristics near the resonance frequency under no load have been investigated. Moreover, using this piezoelectric transformer we measured the LCD backlight characteristics.

• 한국항행학회논문지
• /
• 제24권4호
• /
• pp.299-304
• /
• 2020

본 논문은 평면형 구조를 갖는 원형 부채꼴 모양의 전력 분배기-결합기 설계에 대한 것이다. 이 구조는 직렬형으로 구성할 수 있으며 원형 부채꼴 모양으로 인하여 간단한 회로 구성과 출력의 크기와 위상 발란스 특성을 개선할 수 있으며, 이것은 단순한 입력 정합회로를 갖고 있으며 출력 포트 사이에 RC 병렬 회로를 삽입하여 출력의 반사계수와 고립도를 개선하였다. 설계된 분배기와 결합기는 구조적으로 부채꼴 모양의 대칭적으로 설계되었기 때문에 출력 포트를 2개 또는 4개로 구성하였을 때 출력 사이의 크기 발란스 ± 0.1 dB 와 위상 발란스 ± 1o를 갖는 우수한 특성을 갖고 있다. 이러한 전기적 특성을 확인하기 위해서 동작주파수 2 GHz에서 제작된 평면형 전력 분배기-결합기는 시뮬레이션과 특성이 잘 일치함을 확인하였다.