• 한국기계가공학회지
• /
• 제8권3호
• /
• pp.98-104
• /
• 2009

The objective of this paper is to investigate the effect of factors on the dynamic stiffness variation of boring bar. The experiment was carried out by Taguchi Method and Orthogonal array table. The results indicate that overhang was found out to be dominant factor with 95% confident intervals and feed rate and depth of cut were insignificant. In addition, analysis of loss function shows that loss value increased sharply from 3D to 4D(D is a shank diameter). Consequently, there is critical point which changes property of dynamic stiffness.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.125-134
• /
• 1997

This study was conducted by L9 orthogonal array to obtain optimum spray parameters for This study was conducted by L9 orthogonal array to obtain optimum spray parameters for $Cr_3C_2 - 7wt%$(80wt%Ni-20wt%Cr) coating powder. The factors were hydrogen flow rate, oxygen flow rate, gun-to-work distance, powder feed rate. And evaluation methods for the coating were surface roughness, oxygen concentration, micro-hardness, pore size and distribution, low angle ($30^{\circ}$) erosion rate, and microstructure of coating. The optimum HVOF spray conditions were proved as follows : hydroen flow rate ; 681 SLPM, oxygen flow rate ; 215 SLPM $H^2/O^2 ratio= 3.16), gun-to-work distance ; 22cm, powder feed rate; 25g/min. The hardness (Hv300) was 1147 and the erosion rate ($30^{\circ}$degree) was $3.16\times10^{-4}$g/g. It is believed that the optimized spray conditions can be improved the wear-resistance and anti-erosion characteristics of the coating.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권2호
• /
• pp.171-175
• /
• 1995

Optimum condition of remote plasma enhanced chemical vapor deposition using orthogonal array method was chosen. Characteristics of oxide films deposited by RPECVD with SiH$_{4}$ and N$_{2}$O gases were investigated. Etching rate of the optimized SiO$_{2}$ films in P-etchant was about 6[A/s] that was almost the same as that the high temperature thermal oxide. The films showed high dielectric breakdown field of more than 7[MV/cm] and a resistivity of 8*10$^{13}$ [.ohmcm] around at 7[MV/cm]. The interface trap density of SiO$_{2}$/Si interface around the midgap derived from the high frequency C-V curve was about 5*10$^{10}$ [/cm$^{2}$eV]. It was observed that the dielectric constant of the optimized SiO$_{2}$ film was 4.29.

• 한국ITS학회 논문지
• /
• 제9권1호
• /
• pp.34-41
• /
• 2010

본 논문에서는 복조후 전송 (DF: Decode-and-Forward) 중계기를 사용하는 협력통신 (Cooperative Communication) 시스템에서 동일 채널로 전송된 다른 신호에 의해 단말기에 발생할 수 있는 간섭 완화 방법에 대해 분석하고 실험하였다. 간섭완화 방법은 동일 채널로 전송할 신호를 직교 부호를 이용하여 부호화한 후 전송하면, 수신기는 미리 알고 있는 직교 부호를 이용하여 자신이 원하는 신호만 수신하는 것이다. 본 논문에서 이용한 직교 부호는 직교 골드 부호 (Orthogonal Gold Code) 를 이용하였다. 하지만 직교 골드 부호 이외에 직교 성질을 가지는 다른 부호를 직교 부호로 사용할 수 있다. 또한 추가적인 배열 이득으로 인해 시스템 성능을 향상시키기 위해 시공간 블록 부호화 (STBC : Space Time Block Coding) 개념을 적용하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.487-488
• /
• 2007

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.162-165
• /
• 2004

On this study, we improved diaphgram for micro speaker performance using Taguchi method in discrete design space. The design of diaphgram has an effect on performance of micro speaker such as, thickness of diaphgram, shape of diaphgram, etc. Therefore this study carried to decide shape of diaphgram and thickness of diaphgram for minimizing 2nd natural frequency of diaphgram using Taguchi method. we showed improved design factors that minimized 2nd natural frequency of diaphgram. Also, 2nd natural frequency of diaphgram for micro speaker is reduced up to 37 percent maintaining twist mode shape. From the results of ANOVA, 2nd natural frequency of diaphgram for micro speaker have an effect on position of the outer curved shape and thickness of diaphgram.

• 지능정보연구
• /
• 제5권1호
• /
• pp.1-12
• /
• 1999

강건설계(robust design)는 낮은 비용으로 잡음에 강건한 고품질의 제품이나 공정을 설계하는 체계적이고 효율적인 방법이다. 그러나 강건설계의 과정 중 비표준 직교배열의 사용과 교호인자을 포함한 실험계획은 다소 복잡하고, 전문지식이 필요한 부분으로 비전문가에는 난해한 작업이다. 이를 해결하기 위하여 본 연구에서는 표준직교배열의 변형과 선점도를 이용하여 교호인자를 직교배열의 열에 자동으로 할당하는 전문가시스템 prototype을 개발하였다. 사용자가 수준별 인자수와 교호작용의 유무를 입력하면, 시스템은 적절한 직교배열을 선정하여 필요에 따라 변형하며, 제어인자와 교호작용을 직교배열표에 자동으로 할당하여 출력한다. 개발된 시스템을 사용함으로써 초보자도 직교배열을 쉽게 변형할 수 있으며 다수의 교호인자를 포함한 실험계획을 빠르게 할 수 있다. 본 연구에서 이용된 지식은 문헌에서 추출하였으며, 추론 전략으로는 규칙기반추론(rule-based reasoning)을 이용하였다.

• 대한기계학회논문집
• /
• 제17권10호
• /
• pp.2509-2517
• /
• 1993

Lapping is a very complicated and random process resulting from the variation of abrasive grains in its sizes and shapes and from the numerous factors having an effect on the process quality. Thus it needs to be analyzed by experimental method rather than by theoretical method to obtain the relative effects of factors quantitatively. In this study, cylindrical lapping experiment designed by Taguchi's L8 orthogonal array was performed and analyzed by Yates' ANOVA table. As a result, effective factors and interaction effects were identified and discussed. Also the optimal factor combination to obtain the largest improvement of surface roughness was selected and confirmatory experiments were peformed.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.31-38
• /
• 2012

In this paper, we selected primary cutting parameters that influence on surface roughness of cut bottom surface in end-milling for SM25C material. Those are overhang, depth of cut, feed rate and spindle speed. And then performed orthogonal array experiment and ANOVA by Taguchi method to determine that improved level combination of cutting parameters for betterment of working efficiency and surface roughness one of quality characteristics. And we verified a advisability of prediction model by verification test about level combination. From the results, main cutting parameter influences on surface roughness is spindle speed and the next is feed rate.

• 한국기계가공학회지
• /
• 제8권4호
• /
• pp.48-53
• /
• 2009

Inconel 718 alloy, widely used as material of aircraft engine, has a good mechanical property in high temperature, strong anti-oxidation characteristics in oxidated current over $900^{\circ}C$, and also is not easily digested in the air containing sulfur, therefore, its usage as mechanical component is expanding rapidly. Even though Inconel alloy 718 is difficult to machine, it requires highly precise processing/machining to sustain its component quality of high accuracy. In this paper, general turning operation conditions are tested to select the best cutting process condition by measuring surface roughness through implementing experiments with orthogonal array of cutting speed, feeding speed and cutting depth as processing parameters based on the Taguchi method. Optimal turning operation conditions are extracted from the proposed experimental models.