• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.150.2-150.2
• /
• 2015

In this study, we analyzed the electric and optical characteristics by using various deposition rate ($0.5{\AA}$, $1.0{\AA}$ and $1.5{\AA}/s$) in order to enhance the performance in organic light-emitting devices (OLED). The organic multi-layer structures were deposited with NPB ($500{\AA}$ as hole transport layer), Alq3 ($600{\AA}$ as electron transport layer and emission layer) and LiF ($8{\AA}$ as electron injection layer) via SUNIC PLUS200 on Glass/ITO substrates. In this experiment, we examined the relationship between porous state of organic deposition and mobility of the organic materials. Among the three deposition rates, $0.5{\AA}/s$ achieved the highest performance of (10,786cd/m2, 4.387cd/A) comparing with that of $1{\AA}/s$ (7,779cd/m2, 3.281cd/A) and $1.5{\AA}/s$ (5,167cd/m2, 2.693cd/A). We confirmed that low deposition rate helps to arrange organic materials densely and to move easily another atomic location using inter-chain transporting by orbital overlap.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.6
• /
• pp.512-518
• /
• 2006

In this paper, we investigated the deposition of pentacene thin film on a large area substrate by Organic Vapor Phase Deposition(OVPD) and applied it to fabrication of Organic Thin Film Transistor(OTFT). We extracted the optimum deposition conditions such as evaporation temperature of $260^{\circ}C$, carrier gas flow rate of 10 sccm and chamber vacuum pressure of 0.1 torr. We fabricated 72 OTFTs on the 4 inch size Si Wafer, Which produced the average mobility of $0.1{\pm}0.021cm^2/V{\cdot}s$, average subthreshold slope of 1.04 dec/V, average threshold voltage of -6.55 V, and off-state current is $0.973pA/{\mu}m$. The overall performance of pentacene TFTs over 4 ' wafer exhibited the uniformity with the variation less than 20 %. This proves that OVPD is a suitable methode for the deposition of organic thin film over a large area substrate.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.154-156
• /
• 2005

In the device structure of ITO/tris (8-hydroxyquinoline) aluminum(Alq3)/Al, we investigated the Organic Light-Emitting Diodes (OLEDs) properties as a function of the deposition rate of the $Alq_3$. The deposition rate was from 0.5 to 2.0 $[{\AA}/s]$ in a base pressure of $5{\times}10^{-6}$ [Torr]. It was found that a $Alq_3$ deposition rate of around 1.5 $[{\AA}/s]$ is the optimum for the maximum luminous properties. The optimum deposition rate of $Alq_3$ is 1.5 $[{\AA}/s]$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.264-266
• /
• 2005

Manufacture of OLED device used thermal evaporation method. However thermal evaporation method has many defect as thermal damage of substrate, difficult of dopant rate control and low utilization of organic materials. so we suggest PLD(Pulsed Laser Deposition) method that solution of these problems. PLD method has many advantage as without thermal damage, easy indicate of deposition rate per one pulse and good utilization of organic materials. In this paper we apply the PLD method for manufacture of device so we present high efficiency device manufacture using PLD method that has good deposition uniformity, surface rough and deposition rate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.394-394
• /
• 2012

We fabricated organic-inorganic superlattice films using molecular layer deposition (MLD) and atomic layer deposition (ALD). The MLD is a gas phase process in the vacuum like to atomic layer deposition (ALD) and also relies on a self-terminating surface reaction of organic precursor which results in the formation of a monolayer in each sequence. In the MLD process, 'Alucone' is very famous organic thin film fabricated using MLD. Alucone layers were grown by repeated sequential surface reactions of trimethylaluminum and ethylene glycol at substrate temperature of $80^{\circ}C$. In addition, we developed UV-assisted $Al_2O_3$ with gas diffusion barrier property better than typical $Al_2O_3$. The UV light was very effective to obtain defect-free, high quality $Al_2O_3$ thin film which is determined by water vapor transmission rate (WVTR). Ellipsometry analysis showed a self-limiting surface reaction process and linear growth of each organic, inorganic film. Composition of the organic films was confirmed by infrared (IR) spectroscopy. Ultra-violet (UV) spectroscopy was employed to measure transparency of the organic-inorganic superlattice films. WVTR is calculated by Ca test. Organic-inorganic superlattice films using UV-assisted $Al_2O_3$ and alucone have possible use in gas diffusion barrier for OLED.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.649-652
• /
• 2003

Organic thin-film transistors were fabricated using pentacene as an active electronic material. Device characteristics are improved with increasing the deposition rate of pentacene. It is observed that the deposition rate influences on the interface properties between pentacene and polystyrene, and the molecular ordering of pentacene film. In this paper, we report the effects of the deposition rate of pentacene film on the device performance.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.998-1000
• /
• 2003

We have investigated thin film morphology of pentacene thin films by the process of low-pressure gas assisted organic vapor deposition (LP-GAOVD). Source temperature, inert gas flow rate, substrate temperature and deposition pressure during film deposition is used to vary the growth rate, thin film morphology and the crystalline grain size of pentacene thin films. The electrical properties of pentacene thin films for applications in organic thin film transistor and electrophoretic displays will be discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.12
• /
• pp.1063-1066
• /
• 2009

In this study, we fabricated pentacene organic thin film trasistors(OTFTs) which used aluminum oxide as the gate insulator. Aluminum oxide for OTFTs was deposited on glass substrate with a different deposition rate by E-beam evaporation. In case of the deposition rate of $0.1\;{\AA}$, the fabricated aluminum oxide gate insulating OTFT showed a threshold voltage of -1.36 V, an on/off current ratio of $1.9{\times}10^3$ and field effect mobility $0.023\;cm^2/V_s$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.270-270
• /
• 2016

We fabricated an organic-inorganic nano laminated encapsulation layer using molecular layer deposition (MLD) combined with atomic layer deposition (ALD). The $Al_2O_3$ inorganic layers as an effective single encapsulation layer were deposited at 80 degree C using ALD with alternating surface-saturation reactions of TMA and $H_2O$. A self-assembled organic layers (SAOLs) were fabricated at the same temperature using MLD. MLD and ALD deposition process were performed in the same reaction chamber. The prepared SAOL-$Al_2O_3$ organic-inorganic nano laminate films exhibited good mechanical stability and excellent encapsulation property. The measurement of water vapor transmission rate (WVTR) was performed with Ca test. We controlled thickness-ratio of organic and inorganic layer, and specific ratio showed a lowest WVTR value. Also this encapsulation layer contained very few pin-holes or defects which were linked in whole area by defect test. To apply into real OLEDs panels, we controlled a film stress from tensile to compressive and flexibility defined as an elastic modulus with organic-inorganic ratio. It has shown that OLEDs panel encapsulated with nano laminate layer exhibits better properties than single layer encapsulated in acceleration conditions. These results indicate that the organic-inorganic nano laminate thin films have high potential for flexible display applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.419-419
• /
• 2012

We fabricated the Polyamide 4,6 (PA46) thin film using Adipoyl chloride and 1,4-butadiamine. PA46 film was grown at $70^{\circ}C$ by Molecular Layer Deposition (MLD) method. MLD is sequential and self-terminating fabrication method for organic thin film. The growth rate of PA46 is $3.5{\acute{\AA}}$ cycle. The thickness of PA46 film was measured by Ellipsometer. Surface morphology of this film was investigated by Atomic Force Microscopy (AFM) and roughness is directly proportional to number of growing cycles.