• 상하수도학회지
• /
• 제12권2호
• /
• pp.99-105
• /
• 1998

This research explored the feasibility of preparing and utilizing a preformed polymeric solution of Al(III) for coagulation in water treatment. Slow base(NaOH) injection into supersaturated aluminum chloride solutions did produce high yields of the type of Al polymers useful to water treatment applications. PACl's characteristic analysis showed that the quantity of polymeric Al produced at value of $r(OH_{added}/Al)=2.2$ was 83% of the total aluminum in solution, as showing maximum contents and precipitate was dramatically increased when r was increased above 2.35. And PACl was stable during sitoring period so aging effect was negligible. Results of the coagulation of Nakdong river waters with three PACls showed that the effectiveness of the three coagulants can be considered as r = 2.2 > r = 2.0 > r = 2.35 which are also the order of higher polymeric aluminum contents. Coagulation results for synthetic water exhibited optimum dose of 0.25mM Al, for three PACls, but above optimum dose, r = 2.0 and 2.2 PACl impaired the coagulation and sedimentation of turbidity and humic acid because of the restabilization of particulate. The effect of pH for on coagulation of Nak Dong River water showed that it had much effect turbidity and TOC removal, especially near pH 7. But pH effect was little for turbidity and TOC removal when r = 2.35 PACl was used for coagulation, that PACl had much more precipitates content.

• KCI Concrete Journal
• /
• 제11권3호
• /
• pp.19-28
• /
• 1999

This study treated self-compacting high Performance concrete as two Phase materials of Paste and aggregates and examined the effect of powder and aggregates on self-compacting high performance, since fluidity and segregation resistance of fresh concrete are changed mainly by paste. To improve the fluidity and self-compactibility of concrete, optimum powder ratio of self-compacting high performance concrete using fly ash and blast-furnace slag as powders were calculated. This study was also designed to provide basic materials for suitable design of mix proportion by evaluating fluidity and compactibility by various volume ratios of fine aggregates, paste, and aggregates. As a result, the more fly ash was replaced, the more confined water ratio was reduced because of higher fluidity. The smallest confined water ratio was determined when 15% blast-furnace slag was replaced. The lowest confined water ratio was acquired when 20% fly ash and 15% blast-furnace slag were replaced together. The optimum fine aggregates ratio with the best compactibility was the fine aggregate ratio with the lowest percentage of void in mixing coarse aggregate and fine aggregate In mixing the high performance concrete. Self-compacting high performance concrete with desirable compactibility required more than minimum of unit volume weight. If the unit volume weight used was less than the minimum, concrete had seriously reduced compactibility.

• Advances in concrete construction
• /
• 제14권3호
• /
• pp.215-225
• /
• 2022

Thermal comfort and energy conservation are critical issues in the building sector. Energy consumption in the building sector should be reduced whilst enhancing the thermal comfort of occupants. Concrete is the most widely used construction material in buildings. Its thermal conductivity (k-value) has a direct effect on thermal comfort perception. This study aims to find the optimum value of replacing the normal aggregate with lightweight expanded clay aggregate (LECA) under high strengths and low thermal conductivity, density and water absorption. The k-value of the LECA concrete and its physical and mechanical properties have varying correlations. Results indicate that the oven-dry density, compressive strength, splitting tensile strength and k-value of concrete decrease when normal coarse aggregates are replaced with LECA. However, water absorption (initial and final) increases. Thermal conductivity and the physical and mechanical properties have a strong correlation. The statistical optimisation of the experimental data shows that the 39% replacement of normal coarse aggregate by LECA is the optimum value for maximising the compressive and splitting tensile strengths whilst maintaining the k-value, density and water absorption at a minimum.

• 한국조경학회지
• /
• 제26권1호
• /
• pp.96-112
• /
• 1998

This study aims to evaluate the potential of pro-environmental application(PEP) in streams conceptualized ecological conservation and recreational use to be in harmony with. The main content of research are to clarify the PEP, to establish the evaluation model, and to evaluate 3 streams(Dongchon, Seokhyunchon, Okchon) in Sunchon city. Researchers introduced 12 evaluation items(water quality, water quantity, vegetation-water area, vegetation conservation, streamscape, neighborhood landscape, stream width, optimum area, nearby landuse, facility in stream, distance from user, obstacle to acces) by 5 scales to evaluate the characteristics of natural and artificial factors in stream area and nearby area. Also to decide the weight of items, researchers surveyed the opinion of 22 landscape architects experienced stream-plan through delphi method. Lastly the pro-environmental potential on streams were calculated by the ecological potential and recreational potential indices to be standardized and indicidual sections in streams were divided 5 grades on the basis of PEP. The result of this study are as follows; 1) The evaluation model of PEP was constructed by 4 steps, such as the decision of weight, the measurement of scale, the calculation of potential indices, the gradation of individual sections in streams. 2) The ecological potential were highly influenced by natural factor such as water quality, vegetation conservation, vegetation-water area, but on the other hand the recreational potential were influenced by optimum area, distance from user, water quantity, obstacle to access. 3) The factors such as vegetation conservation, optimum area, nearby landuse, distance from user were function as discernment factors to evaluate relatively ecological and recreational potential. and water quality, water quantity, vegetation -water area, neighborhood landscape were acted as important items to decide PEP.

• 산업기술연구
• /
• 제27권B호
• /
• pp.161-167
• /
• 2007

The objetives of this study are to set up optimum extraction temperature, time and organic solvent for propolis extraction, to investigate chemical properties, and to develop health foods from propolis preparation. In this study, ethanol and ultrasonic extracts method performed to optimum extraction temperature was at 60, $20^{\circ}C$, optimum extraction time was at 12, 4 hours and optimum extraction amount of solvent was at 20, 15 times of propolis weight. When various ethanol solutions were used, whereas flavonoid content was highest in 70, 80% aqueous ethanol, respectively. So the ultrasonic extracts method used gave better results than the ethanol extracts method in this work. Extraction of propolis with etanol and ultrasonic extracts method was performed by using the water and various concentrations of aqueous ethanol as solvent. Sensitivity of propolis samples to Staphylococcus aureus was investigated and the results were shown. Samples of water extract did not inhibit microbial growth, where as 50% aqueous ethanol extract the largest inhibitory zone for Staphylococcus aureus, then decreased inhibition with increasing ethanol concentrations.

• Journal of Biosystems Engineering
• /
• 제12권4호
• /
• pp.31-43
• /
• 1987

This study was performed to develop a hot water boiler system with small scale automatic rice hull furnace for the multi-purpose use in the farm. For the experiment a prototype hot water boiler system with rice hull furnace was fabricated, which was equipped with automatic hull feeder, igniter and ash removal device. Optimum operational conditions of the prototype: system were analyzed. The results arc summarized as follows. 1. The temperature measured right above the burning surface should be higher than $500^{\circ}C$ combustion. 2. The top zone of the combustion chamber was the most suitable location of the thermocouple to pick up the control temperature for the automatic operation of the rice hull furnace. 3. The content of carbon monoxide in the flue gas was increased with the filling height of burning material but it was less than 0.3 percent in volume in this experiment. When the filling height was expressed as the ratio of rice hull feed rate to the volume of the combustion chamber above the burning surface, the optimum ratio was about $150kg/m^3-h$. 4. The combustion efficiency of the prototype was higher than 95 percent when the feed rate was 1.1 to 2.3 kg/h and moisture content of rice hull was 22.4 percent (w.b.) or less. 5. It was estimated that the optimum operational conditions of the system were 1.3 to 2.0 kg/h in feed rate, 70 to 100 percent in excess air and 500 to $510^{\circ}C$ in control temperature. 6. The efficiency of coil heal exchanger increased with a decrease in feed rate of rice hull. When the rice hull feed rates were 1.1, 1.7 and 2.3 kg/h, the efficiencies of coil heat exchanger were about 34, 30 and 25 percent and heat transfer rates were 5.7, 7.6 and 8.8 MJ/h, respectively. When the flat plate heat exchanger was used in addition to the coil heat exchanger, the efficiency of the heat exchanger system increased to 48 percent.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2007년도 학술발표회 논문집
• /
• pp.46-52
• /
• 2007

As flue gas desulfurization (FGD) wastewater contains high concentrations of nitrate and is very low in organic carbon, the feasibility of nitrate removal by autotrophic denitrification using Thiobacillus denitrificans was studied. This autotrophic bacteria oxidizes elemental sulfur to sulfate while reducing nitrate to elemental nitrogen gas, thereby eliminating the need for addition of organic compounds such as methanol. Owing to the unusually high concentrations of dissolved salts $(Ca^{2+},\;Mg^{2+},\;Na^+,\;K^+,\;B^+,\;SO_4^{2-},\;Cl^-,\;F^-,)$ in the FGD wastewater, extensive laboratory-scale and pilot-scale tests were carried out in sulfur-limestone reactors (1) to determine the effect of salinity on autotrophic denitrification, (2) to evaluate the use of limestone for pH control and as source of inorganic carbon for microbial growth, and, (3) to find the optimum environmental and operational conditions for autotrophic denitrification of FGD wastewater. The experimental results demonstrated that (1) autotrophic denitrification is not inhibited up to 1.8 mol total dissolved salt content; (2) inorganic carbon and inorganic phosphorus must be present in sufficiently high concentrations; (3) limestone can supply effective buffering capacity and inorganic carbon; (4) the high calcium concentration may interfere with pH control, phosphorus solubility and limestone dissolution, hence requiring pretreatment of the FGD wastewater; and, 5) under optimum conditions, complete autotrophic denitrification of FGD wastewater was obtained in a sulfur-limestone packed bed reactor with a sulfur:limestone volume ratio of 2:1 for volumetric loading rates up to 400g $NO_{3^-}N/m^3.d$. The interesting interactions between autotrophic denitrification, pH, alkalinity, and the unusually high calcium and boron content of the FGD wastewater are highlighted. The engineering significance of the results is discussed.

• 대한환경공학회지
• /
• 제32권5호
• /
• pp.437-442
• /
• 2010

본 연구에서는 반도체 폐수에 함유된 불소 처리 시 유동상 반응기 (FBR)을 이용하여 불소 제거 효율을 극대화 시키는 조건에서 발생하는 슬러지의 함수율을 최소화 시키고 $CaF_2$의 순도를 높이고자 하였다. 이를 위해 최적 pH 및 $Ca^{2+}$ 주입몰 비 ($[Ca^{2+}]/[F^-]$)가 도출되었다. 연구 결과 pH 및 $Ca^{2+}$ 주입 몰비가 증가함에 따라 불소 제거효율은 증가하였으며, 최적조건에서 79.8%의 불소제거효율이 관찰되었다. 불소 제거 효율이 최적인 조건에서 인 제거 효율은 약 9.3% 로서 불소 제거시 $Ca^{2+}$과 ${PO_4}^{3-}$-P의 부 반응이 거의 발생하지 않아 높은 순도의 $CaF_2$이 침전 슬러지로 발생하는 것으로 나타났다. 또한 이때 슬러지 함수율은 약 19.3%로 매우 낮은 것으로 나타나 불소 제거, 슬러지 순도 및 함수율 측면에서 FBR은 매우 효과적인 불소 제거 공정인 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.607-616
• /
• 2006

More strict construction control of railway roadbeds is demanded in high speed railway system because of heavier repeated dynamic loading than conventional railways. The aim of this study is to propose a compaction control methodology of crushed-rock-soil-fills including as large particles as $200\sim300mm$ in diameter, which are easily encountered in high speed railway roadbed. Field tensity evaluation and in turn compaction control of such crushed-rock-soil-fills are almost impossible by conventional methods such as in-situ density measurements or plate loading tests. The proposed method consists of shear wave measurements of compaction specimens in laboratory and in-situ measurements of fills. In other words, compaction control can be carried out by comparing laboratory and field shear wave velocities using as a compaction control parameter. The proposed method was implemented at a soil site in the beginning and will be expanded to crushed-rock-soil-fills in future. One interesting result is that similar relationship of shear wave velocity and water content was obtained as that of density and water content with the maximum value at the optimum moisture content.

• 한국건축시공학회지
• /
• 제2권3호
• /
• pp.131-138
• /
• 2002

The objective of the study is to examine the characteristic correlations between reinforcing carbon fiber and interfacial adhesion agent since the interfacial adhesion strength between reinforcing carbon fiber and matrices is believed to be an essential element influencing the physical properties in carbon fiber reinforced cement composite using slurry method. The integrity of interfacial adhesion between reinforcing fiber and cement not only affects the quality of fiber reinforced cement composite but also influences to a large degree the physical properties of the cement composite when producing carbon fiber reinforced cement composite using slurry method. Having analyzed the physical properties 1.e., water content, tensile strength, flexural strength and flexural toughness of carbon fiber reinforced cement composite specimens, C-PAM(cation polyacrylamide) was determined to be an optimum interfacial adhesion agent. The study has also demonstrated that interfacial adhesion strength varies largely on the content and type of the reinforcing fiber. Judging from magnified view of the tensile shear cross-section using VMS(video microscope system), interfacial adhesion strength between reinforcing fiber and matrices is affected by the type of interfacial adhesion agent. According to the result of the experiments, C-PAM was determined to be an ideal interfacial adhesion agent when using carbon fiber in producing carbon fiber reinforced cement composite with the optimum content of carbon fiber being established.