• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.708-713
• /
• 2000

The design of experiment(DOE) is getting more attention in the engineering community since it is easy to understand and apply. Recently, engineering designers are adopting DOE with orthogonal arrays when they want to design products in a discrete design space. In this research, a design flow with orthogonal arrays is defined fur structural design according to the general DOE. The design problem is defined as a general structural optimization problem. Sensitivity information is evaluated by the analysis of variance(ANOVA), and an optimum design is determined from analysis of means(ANOM). Interactions between design variables are investigated to achieve additivity which should be valid in DOE. When strong interactions exit, a method is proposed. Some methods to consider the problem are suggested.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권11호
• /
• pp.505-510
• /
• 2005

On this study, we optimized maximizing the thrust force at the TFLM(Transverse Flux Linear Motor) using design of experiments by the table of orthogonal array and the analysis of means(ANOM), and classified the most contributive design factor maximizing the thrust force at the TFLM by analysis of variance(ANOVA). From now on, we are going to apply the required technique to design various uses and shapes of the TFLM.

• 전자공학회논문지S
• /
• 제35S권7호
• /
• pp.46-52
• /
• 1998

This paper presents an experimenal proof for criteria of selecting an optimum adaptive beamforming (ABF) algorithm for a large distorted phased array. A single point target embedded in clutter model is suggested to compare four well-known ABF algorithms. These algorithms are tested to low variance and high variance real data for self-calibrating a large distored phased array. It is shown that these algorithms require at least one dominant scatterer with large radar cross section (RCS) or multiple scatterers with moderate RCS in the field of view. Experimental results are provided to demonstrate the comparisons of the four algorithems in terms of gain loss and image correlaion coefficient, along with corresponding reconstructed cross-range images and range-azimuth images.

• Journal of the Korean Data and Information Science Society
• /
• 제23권4호
• /
• pp.843-850
• /
• 2012

The inferences of data obtained from periodic inspection and type I censoring for the three step stress accelerated life test are studied in this paper. The failure rate function that a log-quadratic relation of stress and the tampered failure rate model are considered under the exponential distribution. The optimal stress change times which minimize the asymptotic variance of maximum likelihood estimators of parameters is determined and the maximum likelihood estimators of the model parameters are estimated. A numerical example will be given to illustrate the proposed inferential procedures.

• 대한산업공학회지
• /
• 제24권3호
• /
• pp.367-379
• /
• 1998

This paper considers two modes of partially accelerated life tests for items having Weibull lifetime distributions. In a use-to-acclerated mode each item is first run at use condition and, if it does not fail for a specified time, then it is run at accelerated condition until a predetermined censoring time. In an accelerated-to-use mode each one is first run at accelerated condition and, if it does not fail for a specified time, then it is run at use condition. Maximum likelihood estimators of the parameters of the lifetime distribution at use condition, and the 'acceleration factor' are obtained. The stress change time for each mode is determined to minimize the asymptotic variance of the acceleration factor, and the two modes are compared. For selected values of the design parameters the optimum plans are obtained, and the effects of the incorrect pre-estimates of the design parameters are investigated. Minimizing the generalized asymptotic variance of the estimators of the model parameters is also considered as an optimality criterion.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.625-632
• /
• 2012

Optimization of process parameters in polymer extrusion is an important task to reduce manufacturing cost. To determine the optimum values of the process parameters, it is essential to find their influence on the strength of polymer breathable thin film. The significance of six important process parameters namely, extruder cylinder temperature, extruder speed, extruder dies temperature, cooling roll temperature, stretching ratio, stretching roll temperature on breathable film strength of polymer extrusion was determined. Moreover, this paper presents the application of Taguchi method and analysis of variance (ANOVA) for maximization of the breathable film strength influenced by extrusion parameters. The optimum parameter combination of extrusion process was obtained by using the analysis of signal-to-noise ratio. The conclusion revealed that extruder speed and stretching ratio were the most influential factor on the film strength, respectively. The best results of film strength were obtained at higher extruder speed and stretching ratio.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1055-1056
• /
• 2011

This paper deals with optimum design criteria for maximum torque density & minimum current density of a single phase line-start permanent-magnet motor (LSPMM) using RSM (Response Surface Methodology) & FEM (Finite Element Method). The focus of this paper is to find a design solution through the comparison of torque density and minimum current density resulting from rotor shape variations. And then, a central composite design (CCD) mixed resolution is introduced, and analysis of variance (ANOVA) is conducted to determine the significance of the fitted regression model.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1059-1060
• /
• 2011

This paper deals with optimum design criteria for maximum torque density & minimum torque ripple of Flux Switching Motor (FSM) using RSM & FEM. The focus of this paper is to find a design solution through the comparison of torque density and torque ripple according to rotor shape variations. And then, a central composite design(CCD) mixed resolution is introduced, and analysis of variance (ANOVA) is conducted to determine the significance of the fitted regression model.

• 전기학회논문지
• /
• 제59권3호
• /
• pp.549-554
• /
• 2010

This paper deals with optimum design criteria for maximum torque density & minimum torque ripple of Flux Switching Motor (FSM) using RSM & FEM. The focus of this paper is to find a design solution through the comparison of torque density and torque ripple according to rotor shape variations. And then, a central composite design(CCD) mixed resolution is introduced, and analysis of variance (ANOVA) is conducted to determine the significance of the fitted regression model.

• 품질경영학회지
• /
• 제27권3호
• /
• pp.79-93
• /
• 1999

The common accelerated life test(ALT) consists of test methods applying a constant stress, higher than the use condition stress, to items. There we, however, situations for which a progressive stress ALT, in which the stress on a test item is continuously increased with time, Is more convenient to perform testing and simpler in analyzing data than a constant stress ALT. When a product under constant stress s follows a Weibull distribution with parameters $\theta$(5) and $\beta$, maximum likelihood(ML) estimators of parameters involved in the model are obtained and their asymptotic distributions are derived under stress bounded ramp tests in which the stress is increased linearly from use condition stress to the stress upper bound. The optimum test plans are also found which minimize the asymptotic variance of the ML estimator of the log mean life at design constant stress. For selected values of the design parameters, tables useful for finding optimal test plans are given. The effect of the pre-estimates of design parameters is studied.