• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.4
• /
• pp.51-56
• /
• 2008

Thermoforming is one of the most versatile and economical processes available for shaping polymer products, but obtaining a uniform thickness of the final product using this method is difficult. Heater power adjustment is very important because the thickness distribution depends strongly on the distribution of the sheet temperature. In this paper, the steady-state optimum distribution of heater power is first ascertained by a numerical optimization to obtain a uniform sheet temperature. The time-dependent optimal heater input is then determined to decrease the temperature difference through the direction of the thickness using the response surface method and the D-optimal method. The optimal results show that the time-dependent optimum heater power distribution gives an acceptable uniform sheet temperature in the forming temperature range by the end of the heating process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.1-9
• /
• 2016

Optimum cross-sectional shape of an automotive disc brake was developed based on FEM thermal analyses and the Taguchi method. Frictional heat flux and convection heat transfer coefficients were first calculated using equations and applied to the disc to calculate accurate temperature distribution and thermal deformations under realistic braking conditions. Maximum stress was generated in an area with highest temperature under pads and near the hat of ventilated disc and vanes. The SN ratio from Taguchi method and MINITAB was applied to obtain the optimum cross-sectional design of a disc brake on the basis of thermal deformations. The optimum cross-section of a disc can reduce thermal deformation by 15.2 % compared to the initial design.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.34 no.1
• /
• pp.29-37
• /
• 1985

During Severe emergencies which result in the case of outage of large generator units, an automatic underfrequency protection scheme can prevent the system frequency from decaying and improve the system stability. This paper presents methods and results of a study on the optimum load shedding scheme which covering as follows. 1) Detail representation of governor model 2) Determination of optimum load shedding amount 3) Selection of action time settings of UFR 4) Comparsson of load shedding programs By this study, the optimum system operating method was recommended for reliable operation of power system.

• 전기의세계
• /
• v.14 no.4
• /
• pp.8-17
• /
• 1965

Firstly, this study has analyzed the following factors affecting the optimum specifications and design of distributive transformers: 1. Facilities installation cost per unit power output. 2. Facilities operating & maintenance cost per unit power output. 3. Production cost per unit power output. 4. Load factor. 5. Loss factor. Secondly, it has clarified the relations between the following factors and the specifications and design of distributive transformers; 1. No-load loss., 2. Load loss., 3. Voltage regulation., 4. Exciting current. Finally, it has determined the method of the most economic design for the transformers using the above factors and relations, and, for optimum the illustrative purpose, suggested their optimum specifications, way of evaluation, and merits by means of typical example.

• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.1
• /
• pp.69-76
• /
• 1989

This paper presents a method of the optimum design for rotating shaft of centrifugal pump. That is, the object is to optimize the system in stability at the operating speed, unbalance response in the vicinity of the rotor critical speed, leakage flow of the seals. The objective function is composed of these three elements and is minimized by changing seal cleareance, diamoters, and lengths. A typical double suction centrifugal pump is analyzed and its objective function is presented. Then the optimum dimensions of seals are obtained, and vibration characteristics at both initial and optimum conditions are investigated.

• Textile Coloration and Finishing
• /
• v.11 no.5
• /
• pp.38-43
• /
• 1999

A calculation method of optimum parameters on dual adsorption isotherm system was examined. The optimum parameters were obtained by non-linear regression analysis based upon a limited solute concentration of dual adsorption isotherm. The results were analyzed with adducing experimental data of formerly reported treaties. The percentage mean deviation of dual adsorption equation calculated with optimum parameters was less than about 5% of experimental data, which was far less than results obtained with parameters of the adduced treatises.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2001.10a
• /
• pp.136-141
• /
• 2001

In this study, computer program for the optimum design of two continuous box culvert was developed. It was shown that even though the starting points and optimization method are different, the objective function and optimum design variables converge to a value within a close range respectively, and consequently the optimum design program developed in this study is reliable and robust. MMFD is the most efficient one from the viewpoint of convergency and computing time.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.2
• /
• pp.95-102
• /
• 2003

In this paper, optimum design is considered over the retaining wall with seismic constraints. The sequential linear programming method(SLP) is used as a rational approach to this optimum design. To make a comparison between the seismic design and the normal design, retaining wall with 4~7m height were adopted. It is shown that the seismic design is more expensive (over 30%) than the normal design for the construction cost.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.12 no.1
• /
• pp.25-32
• /
• 2008

A pin fin is optimized based on the increasing rate of heat loss by using a two-dimensional analytic method. The optimum heat loss, corresponding optimum thermal resistance and fin length are presented as a function of the fin base thickness, convection characteristic numbers ratio, fin outer radius and ambient convection characteristic number. One of the results shows that both the optimum heat loss and fin length decrease linearly whereas the optimum thermal resistance increases very slightly with increase of the fin base thickness.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2000.10a
• /
• pp.206-212
• /
• 2000

In this study, computer program for the optimum design of agricultural aqueduct tunnel was developed. It was shown that even though the starting points and optimization method are different, the objective function and optimum design variables converge to a value within a close range respectively, and consequently the optimum design program developed in this study is reliable and robust. 3D-design drawing can be drawn using automation design computer program developed in this study