• Journal of Soil and Groundwater Environment
• /
• v.10 no.1
• /
• pp.58-64
• /
• 2005

Several tests were conducted to determine the optimum operational conditions of soil washing techniques for floe-forming arsenic-contaminated soils, collected from D abandoned Iron-mine in Korea. The optimum cut-off size was 0.15 mm $(sieve\;\#100)$, about $94\%$ of the mass of soils. Both sodium hydroxide and hydrochloric acid were effective to remove arsenic and the optimum mixing ratio (soil [g] : washing solution [mL]) was 1:5 for both washing agents. Arsenic concentrations, determined by KST Methods, for the dried floe solids obtained from flocculation at pH 5-6 were $990\~1,086\;mg/kg$ dry solids, which were higher concentrations than at the other pH values. Therefore, batch tests for sequential washings with or without removing floc were conducted to find the enhancement of washing efficiencies. After removing floe with 0.2 M HCl, sequential washings of 1 M HCl followed by 1 M NaOH showed the best results (15 mg/kg dry soil). The arsenic concentrations of washing effluent from each washing step were about $2\~3\;mg/L$. However, when these acidic and basic effluents were mixed together, arsenic concentration was decreased to be less than $50\;{\mu}g/L$, due to the pH condition of coagulation followed by precipitation for arsenic removal.

• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.509-515
• /
• 1998

Activated coffee chars were prepared from coffee waste by chemical activation with zinc chloride. In this study, the following processes were carried out ; roasting step, carbonization step, chemical activation step, and washing and drying step. The roasting step of coffee waste was carried out at $300{\sim}400^{\circ}C$ for 10 minutes. The optimum condition of carbonization was at $650^{\circ}C$ for 1 hour. The most important parameter in chemical activation of coffee char was found to be the chemical ratio of activation agents. Activated coffee chars prepared by various activation methods were characterized in terms of the nitrogen BET surface area, the BJH pore volume and pore size distribution at 77 K. The $N_2$-BET surface areas and total pore volume of coffee chars prepared by the chemical activation with $ZnCl_2$ were determined as about $1110{\sim}1580m^2/g$ and $0.51{\sim}0.81cm^3/g$, respectively. Scanning Electron Microscopy (SEM) was used to observe the porosity and surface of activated coffee chars. From the results of SEM analysis, it was shown that active surface and many pores were formed after the chemical activation. The preparation of the activated coffee char from coffee waste was successfully carried out, which previews a possibility for exploitation of resources by recycling the waste.

• Journal of the Korean Ceramic Society
• /
• v.37 no.6
• /
• pp.604-611
• /
• 2000

Glass-ceramics containing a cordierite (2MgO-2Al2O3-5SiO2) as a main crystal phase was prepared from MgO-Al2O3-SiO2 system glass through a controlled 2-step heat treatment for the application to magnetic memory disk substrate for higher storage capacity. Parent glasses prepared with addition of CeO2 as a fulx and TiO2 as a nucleating agent were crystallized by a 2-step heat treatment i.e. nucleation and crystal grwoth. Then the maximum nucleation and crystal growth rates were investigated and several properties such as bending strength, surface hardness and surface roughness were also studied for heat treated glass. As a result, only a $\alpha$-cordierite was precipitated as a main crystal phase for all heat treatment conditions and the maximum nucleation and crystal growth rates were 2.4$\times$109/㎣.hr at 80$0^{\circ}C$ and 0.3${\mu}{\textrm}{m}$/hr at 915$^{\circ}C$ respectively. After being nucleated at 80$0^{\circ}C$ for 5 hours and then crystallized at 915$^{\circ}C$ for 1 hour, the heat treated glass had a crystal volume fraction of 17.6% and crystal size fo 0.3${\mu}{\textrm}{m}$, and showed the optimum properties for the application to magnetic memory disk substrates as follows. ; Bending strength of 192 MPa, Vidkers hardness of 642.1kgf/$\textrm{mm}^2$, and surface roughness of 27$\AA$.

• Journal of the Korean Institute of Navigation
• /
• v.11 no.2
• /
• pp.1-31
• /
• 1987

Nowadays, the transportation of almost all cargoes depends on sea routes in international trade. In the transaction of trade, cargo transportation must be completed on the base of two contrary objectives, one of which is to protect the vessel, cargoes and crew aborad her safely through every step of the transportation and the other is to pursue profits from the transaction of the trade. In spite of the great development of the modern techniques in shipbuilding today, many sea disaters of big merchant vessels have been occurring successively in winter seasons every year on the sea routes of the North Pacific Ocean. Whenever the accident of losing a vessel in rough sea occurred , many experts of the country to which the vessel belonged had tried to take out the reason of the missing without manifesting the exact cause of the unhappy occurrence. In this paper, we calculated ocean wave status along the route of the North Pacific Ocean theoretically concluded by us as optimum on the basis of weather and sea conditions. In the calculation, we used ITTC wave spectrum formula and meteorological data of "Winds '||'&'||' Waves of the north Pacific Ocean" edited by Ship Research Institute of Japan on the basic data assembled by World Meterological Organization through past 10 years. We selected three sample vessels of most common size in the North Pacific Ocean Routes, a container, a log carrier and a bulk carrier and applied tree sample vessels to the calculated sea conditions for getting the rolling angles of the vessels and stress exerting on the hulls. Examining the calculated results, we concluded as follows; 1. Under the condition of these status7 by beaufort scale, "heave to" maneuvering is the best and safest way to steer every vessel. 2. The most dangerous part of sea area along the west bound optimum route of the North Pacific Ocean in winter season, is the southern sea area of the Kamchatka peninsula.a peninsula.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.146-149
• /
• 2002

The aim of stereotactic radiosurgery(SRS) is to deliver a high dose to a target region and a low dose to critical organ through only one or a few irradiation. To satisfy this aim, optimized irradiating conditions must be searched in the planning. Thus, many mathematical methods such as gradient method, simulated annealing and genetic algorithm had been proposed to find out the conditions automatically. There were some limitations using these methods: the long calculation time, and the difficulty of unique solution due to the different shape of tumor. In this study, optimization protocol using ideal models and data base was proposed. Proposed optimization protocol constitutes two steps. First step was a preliminary work. Some possible ideal geometry shapes, such as sphere, cylinder, cone shape or the combination, were assumed to approximate the real tumor shapes. Optimum variables such as isocenter position or collimator size, were determined so that the high dose region could be shaped to fit ideal models with the arrangement of multiple isocenter. Data base were formed with those results. Second, any shaped real targets were approximated to these models using geometry comparison. Then, optimum variables for ideal geometry were chosen from the data base predetermined, and final parameters were obtained by adjusting these data. Although the results of applying the data base to patients were not superior to the result of optimization in each case, it can be acceptable as a starting point of plan.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1962-1965
• /
• 2004

In this paper, the new algorithm for blind adaptive decorrelating parallel interference canceller detector in direct-sequence code division multiple access (DS-CDMA) synchronous communication systems is proposed. The goal of this paper is to improve the performance of the blind adaptive decorrelating parallel interference cancellation detector (BAD/PIC). The proposed blind adaptive decorrelating detector is using optimum step-size technique bootstrap algorithm as an initial stage of PIC, which does not require a training sequence. Therefore, this algorithm has a superior view of utilizing bandwidth and reduces the complexity of computation of inversion cross-correlation matrix. The computer simulation results show that the bit error rate performance of the proposed algorithm for the new structure of detector is better than that of the other detectors such as matched filters, the conventional PIC, and the blind adaptive decorrelating PIC detector.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.56-59
• /
• 1988

The main purpose of Set-up control of hot strip mill plant is to obtain the most regular thickness. Then the learning or adaptive computer control in hot strip rolling mill has been developed. But it is very difficult to keep the inter-stands load distribution ratio uniform; so that the deviation of strip flatness is not avoidable. This leads to the degradation of quality of the products. In this report, an improved method base on the steepest descent method including the computation of optimum step size. This method is applied to the off-line simulation. In consequence, the better balances of inter-stands load distribution is achieved in addition to improvements of output thickness of hot strip mill in POSCO.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.2
• /
• pp.182-191
• /
• 2001

The paper describes the improvement on concurrent subspace optimization(CSSO) via automatic differentiation. CSSO is an efficient strategy to coupled multidisciplinary design optimization(MDO), wherein the original design problem is non-hierarchically decomposed into a set of smaller, more tractable subspaces. Key elements in CSSO are consisted of global sensitivity equation, subspace optimization, optimum sensitivity analysis, and coordination optimization problem that require frequent use of 1st order derivatives to obtain design sensitivity information. The current version of CSSO adopts automatic differentiation scheme to provide a robust sensitivity solution. Automatic differentiation has numerical effectiveness over finite difference schemes tat require the perturbed finite step size in design variable. ADIFOR(Automatic Differentiation In FORtran) is employed to evaluate sensitivities in the present work. The use of exact function derivatives facilitates to enhance the numerical accuracy during the iterative design process. The paper discusses how much the automatic differentiation based approach contributes design performance, compared with traditional all-in-one(non-decomposed) and finite difference based approaches.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.311-318
• /
• 2013

The paper describes the prediction method for the unsteady flow field and the aeroacoustic noise of an small axial fan. The prediction method is comprised of various CFD conditions and acoustic analogy by using Ffowcs Williams-Hawkings equation. The diameter of tested axial fan is 170 mm and number of blade is 5. Virtual anechoic room which has same size with real one was used for CFD. URANS and LES models were used. For mesh dependence study, a different mesh type was tested and optimized mesh was selected. Calculation conditions were also studied such as time step and turbulence model for accurate noise analysis. In this paper, we got optimum analysis conditions and computational results. The unsteady pressure fluctuation at given 4 points were compared between the measured data and computational results. Also, the predicted acoustic spectrum at 3 given microphone points were compared with measured ones.

• Journal of Korea Foundry Society
• /
• v.11 no.6
• /
• pp.455-462
• /
• 1991

The formation of brittle intermetallic compound such as $VAl_3$ tends tp lower the toughness of V-Al alloys. Also, due to the high melting point of vanadium, it is difficult to make that alloy by previous ingot metallurgy method. To depress the technique has been adopted. The effect of particle size and milling time on the phase has been thoroughly studied. For mechanical alloying, SPEX mixed/mill has been used. The milling time and the composition of V and Al are varied to find the optimum condition of forming amorphous phase. The X-Ray Diffrection pattern, microstructure detection, microhandess test, experiments are carried out to analyze MA product. When the final step is reached, no lamellar-structure is detected. The steady state condition is observed after 8 hours and 10 hours milling for 15wt.%Al and 30wt.%Al alloy, respectively. The microhardness continuously increases up to 10 hours after then it remains constant.