• Food Science and Preservation
• /
• v.13 no.2
• /
• pp.216-222
• /
• 2006

Microwave energy (2450 MHz) was applied to extract health-effective component (HEC) from grape seed. Three different solvents approved for grape seed extract such as water, ethanol and acetone, were confirmed in their microwave-heating properties and by which extraction efficiencies were determined. Microwave-assisted extraction (MAE) was performed under different parameters; microwave power : (0, 50, 100 and 150), time : (1, 3, 5, 7, and 9 min), the sample to solvent ratio : (1:20, 1:10, 1:5 and 1:2.5), and particle size(whole, 20, 40 and 60 mesh) and the subsequent extracts were used for determining their physicochemical properties, such as total yield : (TY), total phenolics : (TP), catechin content : (CC), electron donating ability : (EDA), and browning color. The heating properties of solvent demonstrated the optimal ranges of microwave and time as 100 W and 2 to 6 min. The TY and HFC content were higher with increasing powers in water and ethanol solvent, while HFC content were lower in acetone at over 100 W. The longer of extraction time up to 5 min, the higher extraction efficiency. Based upon the overall MAE efficiency and solvent recovery, it was found optimal to use 10 times volume of ethanol for 10 mesh of seed particle at 100 W.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.17 no.4
• /
• pp.79-90
• /
• 2021

This paper presents a study to reduce the effect of blast pressure on the blast valves installed in protection tunnels, where the shape of the tunnel entrance and the blast pocket is optimized based on the predetermined basic shape of the protective tunnels. The reliability of the numerical tunnel models was examined by performing analyses of mesh convergence and overpressure stability and with comparison to the data in blast-load design charts in UFC 3-340-02 (DoD, 2008). An optimal mesh size and a stabilized distance of overpressure were proposed, and the numerical results were validated based on the UFC data. A parametric study to reduce the blast overpressures in tunnel was conducted using the validated numerical model. Analysis was performed applying 1) the entrance slope of 90, 75, 60, and 45 degrees, 2) two blast pockets with the depth 0.5, 1.0, and 1.5 times the tunnel width, 3) the three types of curved back walls of the blast pockets, and 4) two types of the upper and lower surfaces of the blast pockets to the reference tunnel model. An optimal solution by combining the analysis results of the tunnel entrance shape, the depth of the blast pockets, and the upper and lower parts of the blast pockets was provided in comparison to the reference tunnel model. The blast overpressures using the proposed tunnel shape have been reduced effectively.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.23 no.2
• /
• pp.65-92
• /
• 2019

We survey a recently developed immersed finite element method (IFEM) for the interface problems. The IFEM uses structured grids such as uniform grids, even if the interface is a smooth curve. Instead of fitting the curved interface, the bases are modified so that they satisfy the jump conditions along the interface. The early versions of IFEM [1, 2] were suboptimal in convergence order [3]. Later, the consistency terms were added to the bilinear forms [4, 5], thus the scheme became optimal and the error estimates were proven. For elasticity problems with interfaces, we modify the Crouzeix-Raviart based element to satisfy the traction conditions along the interface [6], but the consistency terms are not needed. To satisfy the Korn's inequality, we add the stabilizing terms to the bilinear form. The optimal error estimate was shown for a triangular grid. Lastly, we describe the multigrid algorithms for the discretized system arising from IFEM. The prolongation operators are designed so that the prolongated function satisfy the flux continuity condition along the interface. The W-cycle convergence was proved, and the number of V-cycle is independent of the mesh size.

• Journal of Mushroom
• /
• v.21 no.3
• /
• pp.110-117
• /
• 2023

Cordycepin (3'-deoxyadenosine) is a nucleoside analog known for its diverse range of biological activities. This study investigated the effect of different types of sawdust on the production of the bioactive compound cordycepin. The results of the study showed that different types of wood sawdust affected the biosynthesis of cordycepin and a significant increase was observed when the conventional SDB medium was replaced with 1% NaOH treated pine sawdust. To optimize cordycepin production from Paecilomyces tenuipes in a medium containing 1% NaOH-pretreated pine sawdust, we employed Response Surface Methodology (RSM) in its Box-Behnken design (BBD) canonical form. The optimal conditions were determined as follows: a particle size of 109.5111-mesh (140 ㎛) for 1% NaOH-pretreated pine sawdust, an input weight of 21.1679 g/L, and an incubation time of 73.8423 hours. According to our model, this combination is expected to yield a maximum cordycepin content of 896.1428 ㎍/mL. Experimental validation of this prediction was performed using the suggested optimal conditions, resulting in an average cordycepin content of 922.6771 ㎍/mL across three replicates, thus confirming the model's accuracy.

• Journal of Sensor Science and Technology
• /
• v.25 no.6
• /
• pp.399-405
• /
• 2016

Scent diffuser using micro-pore piezo actuator achieved a commercial success because of its cheap production cost, but it is easy to be use for IT-based contents due to difficulty of scent intensity control. To solve this problem, we control the emission amount of scent diffuser by changing amplitude and frequency of input voltage applied to micro-pore piezo actuator. And, we analyzed the effect of density of cotton core on emission amount and a relationship between hole-size of mesh in piezo actuator and viscosity of scents to design a mechanically optimal scent device.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.4
• /
• pp.96-101
• /
• 2015

In the previous study, we investigated the physical properties of new organic fillers made from major agricultural byproducts, including rice husks, peanut husks and garlic stems, and we estimated that rice husk was the best candidate for use as new organic fillers in paperboard. In this study, an organic filler prototype was produced with rice husk and the mill trials were carried out in a white liner chipboard (duplexboard) mill. The rice husk organic filler was added to the middle ply of SC $350g/m^2$ to determine the optimal conditions for the manufacture of rice husk organic fillers. The mill trials were performed three times and the bulk improvement and drying energy reduction were measured to identify the functionality of the rice husk organic filler compared to that of the commercial wood powder. In the first mill trial, the test failed because the surface roughness of the duplexboard had deteriorated after the rice husk organic filler was added to the OCC stock. As all of the particles remaining on the 60 mesh sieves were removed and the particle size was decreased by increasing the length of the grinding process, the surface roughness of the duplexboard did not be deteriorated in the second mill trial. However, the bulk improvement and drying energy reduction were not observed. In the final mill trial, as the particle size of the rice husk organic filler was controlled by increasing the portion of particles passing through the 60 mesh sieves and remaining 100 mesh sieves, higher bulk improvement and drying energy reduction were acquired compared to the commercial wood powder.

• Korean Journal of Food Science and Technology
• /
• v.26 no.3
• /
• pp.305-309
• /
• 1994

Precooked powder of redbean porridge (RP) was prepared by the series of process extrusion, drying, milling and blending with a mixture of whole redbean flour and corn starch and others. The optimum process and quality of products for RP were investigated. After extrusion under the moisture content 24 to 26%, twin screw speed 350 rpm, extrusion temperature 150 to $155^{\circ}C$ and feed rate 60 kg/hr, the product had a higher quality with its natural redbean flavor/color. During the extrusion process, extrusion temperature and specific mechanical energy increased from 150 to $198^{\circ}C$ and from 134 to 144 kwh/ton respectively, as the amount of addition water decreased from 6 to 2 kg/hr. By the hot air drying of redbean extrudate (RE). it could be dried below to 4% moisture content, of which level considered as an optimal moisture content for anti-caking of the powdered product, at $80^{\circ}C$ for 4hrs and at $100^{\circ}C$ for 1.5 hrs respectively. In the sieve analysis of extrudate powder, when the product milled through a mesh size of 0.5 mm or 1.0 mm, about 80% or 65% of the feed was passed a 65 mesh screen respectively. Moisture absorption of final blended products was formed a cake under 100% of relative humidity after 13 hrs of storage. As the amount of RE powder reduced, the flavor score of products decreased by sensory evaluation of products prepared by the different ratio of RE powder, corn starch and sugar.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.68 no.1
• /
• pp.20-26
• /
• 2023

Fiber content in the storage roots of sweetpotato varies between different varieties. For examples, the high fiber content of certain types has a poor texture when steamed or roasted. This study was conducted to evaluate the optimal sieve mesh size for separating fibers, the chemical composition of fibers and differences in fiber content among different varieties. We found that the separated fiber content (dry weight) of mashed and steamed sweetpotato was higher after washing three times (143.3 mg/100 g) compared with that washed five times (128.4 mg/100 g). The Hogammi variety remained 85.9% of total fiber content at 10 mesh (2,000 ㎛) and 9.6% of total fiber content at 30 mesh (600 ㎛), and Jinyulmi remained 74.9 and 16.7% of total fiber content , respectively. Therefore, a 30 mesh sieve was considered the most suitable for fiber separation. Among the 10 studied cultivars, Jinhongmi showed the lowest amount of fiber (24.8 mg/100 g) and Hogammi had the highest amount (111.4 mg/100 g), which was 4.5 times larger than that of Jinhongmi. Cellulose, hemicellulose and lignin content of separated fibers showed no difference between the viscous-type Hogammi and powdery-type Jinyulmi varieties, with averages of 32.5, 22.3 and 29.6%, respectively. Correlation results using the Image J program showed a significant correlation between the distribution of the stained area and the fiber content (R = 0.74, p < 0.05). Staining distribution differed among varieties, suggesting that a simple fiber content test could be performed using the staining method on raw sweetpotato. These results provide useful information to help inform farmers on the fiber content of different sweetpotato varieties.

• Journal of Forest and Environmental Science
• /
• v.24 no.1
• /
• pp.53-59
• /
• 2008

Extracellular enzyme activities of Fomitopsis palustris were determined by the particle sizes, culture periods and concentrations of wood particle substrate which was mixture of 4 domestic coniferous woods, such as Pinus densiflora, Larix leptolepsis, Pinus koraiensis, and Pinus rigida. The results showed that the culture conditions had an effect on the secretion of most of the extracellular enzymes from Fomitopsis palustris in the mixed wood particle substrate. :The optimal culture conditions for enzyme activities were 80~100 mesh in wood particle size, 7.5% in concentrations of wood substrate, and 4~8 weeks in culture period.

• Journal of Mushroom
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2021

The choice of the culture medium is an important factor for the mass production of mycelia in submerged cultures. The influence of liquid medium on the mycelial dry weight of Paecilomyces tenuipes was investigated in this study. The regression equation is expressed as Y=-1292.94187+17.78612X1+18.92425X2+2.11464X3-0.019375X1X2-0.006276X1X3+0.008177X2X3-0.070169X12-0.292175X22-0.008818X32, where Y represents the value of the mycelial dry weight (g/L), X1 is the particle size of wood sawdust in liquid medium (mesh), X2 is the concentration of the wood sawdust in liquid medium, and X3 is incubation time (h). The medium was optimized using a response surface methodology, and the optimal medium contained 30 g of wood sawdust (140 mesh), 20 g of glucose, and 10 g/L of peptone. Under these conditions, the mycelial dry weight reached 38.1 g/L (actual value). The culture medium containing wood sawdust is simple and easy to use, highly efficient, and eco-friendly, and its effectiveness in large preparations of P. tenuipes mycelia with low material costs has been demonstrated.