• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.5
• /
• pp.769-772
• /
• 2016

In this paper, the overhang structure was applied to the axial flux permanent magnet (AFPM) motor. This paper describes the overhang effect in the AFPM motor. Moreover, the overhang effect was analyzed according to the different overhang length and an optimal overhang structure was proposed. Finally, the proposed structure was applied to design, analysis and experiment of prototype motors. Through the comparison between 3D finite element analysis results and experimental ones, the validity of proposed structure is clarified.

• Structural Engineering and Mechanics
• /
• v.74 no.4
• /
• pp.533-545
• /
• 2020

An optimal design method for a spoke double-layer cable-net structure (SDLC) is proposed in this study. Simplified calculation models of the SDLC are put forward to reveal the static responses under vertical loads and wind loads. Next, based on an energy principle, the relationship among the initial prestress level, cross-sectional areas of the components, rise height, sag height, overall displacement, and relative deformation is proposed. Moreover, a calculation model of the Foshan Center SDLC is built and optimized. Given the limited loading cases, material properties of the components, and variation ranges of the rise height and sag height, the self-weight and initial prestress level of the entire structure can be obtained. Because the self-weight of the cables decreases with increasing of the rise height and sag height, while the self-weight of the inner strut increases, the total weight of the entire structure successively exhibits a sharp reduction, a gradual decrease, a slow increase, and a sharp increase during the optimization process. For the simplified model, the optimal design corresponds to the combination of rise height and sag height that results in an appropriate prestress level of the entire structure with the minimum total weight.

• Journal of KSNVE
• /
• v.8 no.3
• /
• pp.428-434
• /
• 1998

Optimal design of a piezoelectric smart structure is studied for cabin noise control. A cubic shaped acoustic cavity with a flat plate which covers one side is taken as the problem. The sensor signal is returned to the actuator through a negative gain. The acoustic cavity is modeled using the modal approach which represents the pressure fields in the cavity as a sum of mode shapes of the cavity with unknown coefficients. By using orthogonality of the mode shapes of the cavity, finite element equation for the structure with the influence of the acoustic cavity is derived. The objective function is the average pressure at a certain region, so-called silent zone, in the cavity and the design variables are the locations and sizes of the piezoelectirc actuator and sensor. The optimal design is performed at several frequencies and the results show a remarkable noise reduction. To see the robustness of the optimally designed result, the configuration is used to examine the noise reduction at different frequencies. By adjusting the gain at each frequencies, it is possible to reduce the noise in comparison with the result when the actuator is not activated.

• Journal of Korean Association for Spatial Structures
• /
• v.19 no.2
• /
• pp.43-50
• /
• 2019

A smart connective control system was invented recently for coupling control of adjacent buildings. Previous studies on this topic focused on development of control algorithm for the smart connective control system and design method of control device. Usually, a smart control devices are applied to building structures after structural design. However, because structural characteristics of building structure with control devices changes, a iterative design is required for optimal design. To defeat this problem, an integrated optimal design method for a smart connective control system and connected buildings was proposed. For this purpose, an artificial seismic load was generated for control performance evaluation of the smart coupling control system. 20-story and 12-story adjacent buildings were used as example structures and an MR (magnetorheological) damper was used as a smart control device to connect adjacent two buildings. NSGA-II was used for multi-objective integrated optimization of structure-smart control device. Numerical simulation results show the integrated optimal design method proposed in this study can provide various optimal designs for smart connective control system and connected buildings presenting good control performance.

• International Journal of Automotive Technology
• /
• v.5 no.3
• /
• pp.189-194
• /
• 2004

The viscoelastic layer material is widely used to control the noise and vibration characteristics of the panel structure. This paper describes the design technology of the effective vibration damping treatment using the concept of the equivalent parameter of viscoelastic layer materials. Applying the equivalent parameter concepts based on theories of shell, it is possible to simulate the finite element analysis of damping layer panel treatments on the vibration characteristics of the structure. And it is achieved the reduced computational cost and the optimal design of topological distribution for the reduction of vibration effect.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.4
• /
• pp.66-72
• /
• 2003

This paper proposes an optimum, problematic design for structural and control systems, taking a 3-D truss structure as an example. The structure is subjected to initial static loads and time-varying disturbances. The structure is controlled by a state feedback H$_{\infty}$ controller which suppress the effects of disturbances. The design variables are the cross sectional areas of truss members. The structural objective function is the structural weight. For the control objective, we consider two types of performance indices, The first function represents the effect of the initial loads. The second function is the norm of the feedback gain, These objective functions are in conflict with each other but are transformed into one control objective by the weighting method. The structural objectives is treated as the constraint, By introducing the second control objective which considers the magnitude of the feedback gain, we can create a design to model errors.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.10a
• /
• pp.266-271
• /
• 1996

Optimal design of disk shaped piezoelectric actuator and sensor mounted on the plate structure is studied for the control of noise radiated fro the structure. The sensor signal is returned to the actuator through negative gain. Finite element modelling is used for the plate structure and the disk shaped piezoelectric sensor and actuator. The objective function is the total radiated sound power and the design variables are the locations and sizes of the piezoelectric actuator and sensor. The optimal is performed at the resonance and the off resonance frequency and the results show good noise reduction.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3
• /
• pp.356-363
• /
• 2013

Mechanical molding press which is used for transformation process during semiconductor manufacturing process has structural deformations by pressure. If these deformations have over limit range, life of the press itself can be reduced and it will be exerted on a bad effect for quality of the semiconductor. In this research, the main plates and links of a press are analyzed in relation to the structural deformations caused by pressure excluding thermal deformations. After modifying the modeling, the analysis is performed again to determine optimal design of the press, and this design is introduced to ensure that most of the stresses on the main plates are within safe allowable limits. As a result, an optimal design method for the structure is investigated to produce the desired pressure even when the size of the main structure is minimized.

• Structural Engineering and Mechanics
• /
• v.81 no.6
• /
• pp.677-689
• /
• 2022

Generally, the goal of seismic retrofit design of an existing structure using energy dissipation devices is to determine the optimum design parameters of a retrofit device to satisfy a specified limit state with minimum cost. However, the presence of multiple parameters to be optimized and the computational complexity of performing non-linear analysis make it difficult to find the optimal design parameters in the realistic 3D structure. In this study, genetic algorithm-based optimal seismic retrofit methods for determining the required number, yield strength, and location of steel slit dampers are proposed to retrofit an asymmetric soft first-story structure. These methods use a multi-objective and single-objective evolutionary algorithms, each of which varies in computational complexity and incorporates nonlinear time-history analysis to determine seismic performance. Pareto-optimal solutions of the multi-objective optimization are found using a non-dominated sorting genetic algorithm (NSGA-II). It is demonstrated that the developed multi-objective optimization methods can determine the optimum number, yield strength, and location of dampers that satisfy the given limit state of a three-dimensional asymmetric soft first-story structure. It is also shown that the single-objective distribution method based on minimizing plan-wise stiffness eccentricity turns out to produce similar number of dampers in optimum locations without time consuming nonlinear dynamic analysis.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.1
• /
• pp.73-80
• /
• 2012

It is important to design the optimal shape in the initial process because the influences on the design and construction are large according to the shape and pattern of spatial structures. However, the existing optimal shape designs for spatial structure are performed by the designer's intuition and experiences. Therefore, this study proposes the integrated process using the topology optimization and cellular automata model. First, the initial optimal shapes are obtained by using the topology optimization, and then the spatial truss structural patterns are created through the application of cellular automata rules. Finally, the optimal shapes to satisfy the various design conditions are generated by the structural analysis and size optimization.