• Journal of Korea Water Resources Association
• /
• v.48 no.12
• /
• pp.1065-1075
• /
• 2015

In the estuary where the structure such as river-mouth weir has been installed, the flow is developed very complicatedly due to river water from upstream, tide of the sea and floodgate operation. Especially, if basin outlets more than one exists in one estuary, the boundary conditions will be significantly more complex form. Saemangeum(SMG) project area in Korea is the most typical example. There are Mankyung river and Dongjin river in upstream. The water of them inflows into SMG project area. In the downstream, river flow was drained from inland to sea over the SMG sea dike through the sluice. The connecting channel was located between Mankyung and Dongjin basins. It functions not only as transportation by ship in ordinary period but also as flood sharing by sending flood flow to each other in flood period. Therefore, in order to secure the safety against flood, it is very important to understand the flood sharing capacity for connecting channel. In this study, the flood control effect was analyzed using numerical simulation. Delft3D was used to numerical simulation and simulated period was set up with neap tide, in which the maximum flood stage occurred due to poor drainage. Actually, three connecting channels were designed in land use plan of the SMG Master Plan, but they were simplified to a single channel for conciseness of analysis in this study. According to the results of numerical analysis, the water level difference between two basins was increased and the maximum flood stage at dike sluice was also upraised depending on decrease of conveyance. And the velocity induced by same water level difference was decreased when the conveyance became smaller. In certain conveyance above, there was almost no flood control effect. Therefore, if the results of this study are considered for design of connecting channel, it will be expected to draw the optimal conveyance for minimizing dredging construction cost while maximizing the flood control effect.

• Journal of Technology Innovation
• /
• v.24 no.4
• /
• pp.27-53
• /
• 2016

This case analyzed the efficiency of 79 R&D projects performed within one private research center in machine tools industry. DEA was used for efficiency analysis. Input variables were R&D investment expense and man-month. Output variables were achievement rate on target development period and expected net sales within 5-years. Samples are divided into product development, Prior technology development, and control technology development. The key result is that Prior technology showed the lowest efficiency because of high uncertainty. It was so difficult to determine its goals and to make its specific plans. With respect to scale, the proportions of CRS(constant returns to scale) were 34.6%, 14.3% and 38.9% for product development, prior technology, control technology respectively. As for IRS(increase returns to scale), they were 53.8%, 85.7% and 38.9% for product development, prior technology, control technology respectively. As for DRS(decrease returns to scale) they were 11.5%, 0% and 22.2% for product development, prior technology, control technology respectively. On the whole, in this case, insufficient input was more problematic than excessive input, which means the lack of investment in R&D. Prior technology can be the source of the future competitiveness of companies. To operate inefficient DMU efficiently, the optimal input should be managed and it is derived from comparison with the reference group.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.11 no.1
• /
• pp.11-28
• /
• 2005

Spasticity has been defined as "a motor disorder characterized by a velocity-dependent increased in tonic stretch reflexes with exaggerated tendon jerks, resulting from hyperexcitability of the stretch reflex, as one components of the upper motorneuron syndrome". Spasticity is one of the common symptoms of stroke patients and frequently interferes with the motor functions such as gait, posture and activities of daily living. Therefore, its management is becoming a major issue in physical therapy. The purpose of this study was to determined the effects of reciprocal inhibition by isometric contraction of pre-tibia muscle on spasticity in hemiplegic patients through Hoffmann reflex. The subjects were consisted 45 patients who had hemiplegia due to stroke. All subjects randomly assigned to 3 group: manual reciprocal inhibition program group(manual group), neuromuscular electrical stimulation group(NMES group) and control group. The manual group received voluntary isometric contraction of pre-tibia muscle. The NMES group received neuromuscular electrical stimulation on tibialis anterior. The control group was not received any therapeutic intervention. Before and after experiments, Hoffmann reflex, M-wave and Modified Ashworth scale was measure in all patients. The data of 30 patients who complete experimental course were statistically analysed. Modified Ashworth scale were significantly decreased after experiment in manual group(p<.01). The Hmax/Mmax ratios were significantly decreased after experiment in manual group(p<.o1). There were no statistical difference between pre-test and post-test with modified Ashworth scale in NMES group(p>.01). There were no statistical difference between pre-test and post-test with Hmax/Mmax ratios in NMES group(p>.01). There were no statistical difference between pre-test and post-test with modified Ashworth scale in control group(p>.01). There were no statistical difference between pre-test and post-test with Hmax/Mmax ratios in control group(p>.01). The present results revealed that reciprocal inhibition which produced by voluntary isometric contraction of pre-tibia muscle can be reduce spasticity of gastrocnemius. Therefore, reciprocal inhibition is useful to improve functional activities in hemiplegic patient. Further study should be done to analyse the effects of intervention duration of reciprocal inhibition, appropriate muscle contraction, optimal time to apply the reciprocal inhibition in more long period.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.631-638
• /
• 2022

Microgrid, which enables the production and consumption of electricity to be done independently on a small scale, has been studied on one of the solutions of reinforcement for flexibility of electronic system. This study examined the application effect of new microgrid by applying hybrid battery in electric power storage device. We designed the system to highlight the advantage of each battery and complement the disadvantage by using hybrid system with Lithium-ion battery and interval Redox flow battery. It runs with lithium-ion battery during the initial startup while the Redox flow battery operates for a long time at the end of excessive period, and it enables a discharge of Lithium-ion and Redox flow battery at the same time when the load has a large output. We chose Maldives as a subject of this study for organizing and optimizing independent microgrid. Maldives is the country to accomplish 100% domestic electricity in South Asia, but the whole electric power is supplied through diesel generation imported fossil fuel. We organized and optimized microgrid for energy independence on Malahini island to solve Maldives energy cost problem and global energy environment matters. We analyzed the daily power supply and accumulated the power supply from September 18, 2018~February 11, 2019. The accumulated power supply was about 120.4 MWh and the daily power supply was about 800~1000 kWh. Based on the collected information, we divided the cases into three models which are only diesel generator, solar generator as well as diesel generator, and solar+ESS+diesel generator. We analyzed the amount of oil consumption compared to the cost of construction and power output. The result showed that solar+ESS+diesel generator was most economically feasible. As well, we obtained that our considering hybrid battery system reduced the fuel consumption for diesel power generation about 10~15%.

• Journal of Bio-Environment Control
• /
• v.20 no.2
• /
• pp.93-100
• /
• 2011

Maintenance of adequate soil water potential during the period of crop growth is necessary to support optimum plant growth and yields. A better understanding of soil water movement within and below the rooting zone can facilitate optimal irrigation scheduling aimed at minimizing the adverse effects of water stress on crop growth and development and the leaching of water below the root zone which can have adverse environmental effects. The objective of this study was to evaluate the feasibility of using a portable irrigation controller with an Watermark sensor for the cultivation of drip-irrigated vegetable crops in a greenhouse. The control capability of the irrigation controller for a soil water potential of -20 kPa was evaluated under summer conditions by cultivating 45-day-old tomato plants grown in three differently textured soils (sandy loam, loam, and loamy sands). Water contents through each soil profile were continuously monitored using three Sentek probes, each consisting of three capacitance sensors at 10, 20, and 30 cm depths. Even though a repeatable cycling of soil water potential occurred for the potential treatment, the lower limit of the Watermark (about 0 kPa) obtained in this study presented a limitation of using the Watermark sensor for optimal irrigation of tomato plants where -20 kPa was used as a point for triggering irrigations. This problem might be related to the slow response time and inadequate soil-sensor interface of the Watermark sensor as compared to a porous and ceramic cup-based tensiometer with a sensitive pressure transducer. In addition, the irrigation time of 50 to 60 min at each of the irrigation operation gave a rapid drop of the potential to zero, resulting in over irrigation of tomatoes. There were differences in water content among the three different soil types under the variable rate irrigation, showing a range of water contents of 16 to 24%, 17 to 28%, and 24 to 32% for loamy sand, sandy loam, and loam soils, respectively. The greatest rate increase in water content was observed in the top of 10 cm depth of sandy loam soil within almost 60 min from the start of irrigation.

• Journal of Bio-Environment Control
• /
• v.28 no.3
• /
• pp.185-196
• /
• 2019

Abstract. This research was conducted to figure out the optimal size of the plug cell and seedling raising period in 'Nongwoo' and 'Nonghyeop' cultivars. In the first experiment on effect of plug cell size on growth of squash, seedlings were transplanted into hydroponic cultivation beds at different growing stages: Those in 32-cell trays with 3-4 true leaves at 25 days after sowing, those in 50-cell trays with 2 true leaves at 15 days after sowing, those in 105-cell trays just before a true leaf development, and those in 162-cell trays with only cotyledons at 8 days after sowing. In the second experiment on effect of seedling raising period on growth of squash, it was conducted to have different sowing dates. But the same transplanting date, based on the results of Experiment 1, and compared the differences in growth and fruit productivity as affected by plug cell size in the same way with experiment 1 including the cultivars and environmental conditions. After setting the transplanting date in advance, the number of days for sowing were calculated back for each treatment. In the first experiment, plant height was the greatest in 105-cell trays followed by 162, 50 and 32-cell trays in both cultivars. The best fruit quality was found in different treatments depending on the cultivars, although it was the lowest in 32-cell trays in both cultivars. The fruit quality was not significantly different among those from cell sizes. Therefore, when raising seedlings in 105-cell trays, the period of raising seedlings can be shortened as compared with the conventional 32-cell trays, and this change could reduce the workforce required for growing and transplanting seedlings. In the second experiment, after transplanting, shoot height and leaf width in the first measurement in both cultivars were greater in the 32-cell treatment. However, the last measurement after four weeks showed no significant difference in plant height, but significantly greatest leaf width in the smallest cell treatment, even as compared with that in 32-cell treatment. In case of 'Nongwoo', length and weight of the first harvested fruit showed the highest values in the treatment of 105-cell trays. In case of 'Nonghyeop' the 162-cell treatment along with the 105-cell treatment showed greatest length and weight of the first fruits. From these results, zucchini plug seedlings can be raised in plug trays with reduced cell sizes than the conventional 32-cell trays with improved fruit productivity.

• Journal of fish pathology
• /
• v.26 no.2
• /
• pp.59-64
• /
• 2013

This study aimed to develop an algorithm to determine the optimal injection position in olive flounder, Paralichthys olivaceus when a vaccine is injected into the fish by using a vision-based automatic equipment measruing the total length (TL), width and weight of the fish. Over a 5-month period, 500 olive flounders were examined to analyze the relation of the fish size and to the shape and location of its abdomen, using radiography, a ruler plate and scale. There were significant correlations between the TL and the shape and location of the abdomen. The abdomen was located 0.232TL - 2.7221 mm ($R^2$=0.8787) from the end of the mouth of the fish. The height and width of the abdomen in the fish were 0.1292TL + 1.8768 mm ($R^2$=0.7935) and 0.183TL-5.9791 mm ($R^2$=0.8641), respectively. The injection point in the abdominal region avoiding organs was determined by calculating the center of gravity of the abdomen volume. This can be expressed as g (0.2759TL - 2.0965, 0.1295TL - 4.2325) on the basis of TL line coordinates. The injection point by the expressed coordinates had errors for the x and y axes as 12.15 mm and 8.28 mm, respectively. These were enough to use the algorithm to injection for the equipment. This automated method to determine the position of any part in the fish can also be used for other purposes, for example, intramuscular injection or auto-tagging of fish.

• Journal of Environmental Science International
• /
• v.17 no.4
• /
• pp.439-449
• /
• 2008

Algicidal bacterium was isolated from sea water during the declining period of Cochlodinium polykrikoides blooms and this bacterium had a significant algicidal activity against C. polykrikoides. In this study, algicidal bacterium was identified on the basis of biochemical and chemotaxonomic characteristics, and analysis of 16S rDNA sequences. The algicidal bacterium showed 98.6% homology with Micrococcus luteus ATCC $381^T$. Therefore, this bacterium was designated Micrococcus luteus SY-13. The optimal culture conditions of the algicidal bacterium was $25^{\circ}C$, initial pH 8.0, and 3.0% NaCl concentration. M. luteus SY-13 is assumed to produce secondary metabolites which have algicidal activity. When 10% culture filtrate of this strain was applied to C. polykrikoides ($1.0\;{\times}\;10^4\;cells/ml$) cultures, over 98% of C, polykrikoides cells were destroyed within 6 hours. The culture filtrate of M. luteus SY-13 exhibited similar algicidal activity after heat-treatment at $121^{\circ}C$ for 15 min. While algicidal activity remained in filtrates with pH adjusted to 8.0, loss of algicidal activity occurred when the pHs of filtrates were adjusted to over 9.0 or heat-treated at $121{\times}180^{\circ}C$ for 1 hour. M. luteus SY-13 showed significant algicidal activities against C. polykrikoides (98.9%) and a wide algicidal range against various harmful algal bloom (HAB) species. However, there was no algicidal effect on diatom and marine livefood organisms except Isocrysis galbana. These results suggest that M. luteus SY-13 could be a candidate for use in the control of HABs.

• The KIPS Transactions:PartC
• /
• v.8C no.1
• /
• pp.75-87
• /
• 2001

The Conditional Access System is the complete system for ensuring that broadcasting services are only accessible to those who are entitled to receive them. Four major parts to this system are scrambling, descrambling, authentication and encryption. For the proper operation, which means hard-to- break and uninterrupted service, secure key management and efficient delivery mechanism are very important design factors to this system. Performance analysis is another important factor to this system that is used in massive subscriber environment. In this thesis, one of the secure and efficient key management mechanisms is proposed. For the secrecy of this mechanism, hierarchical stacking of keys and key generation matrix are proposed. For the proof of efficient delivery of those keys, simulation results and performance analysis. which is based on queuing analysis, are presented. Lastly, optimal key generation and delivery period, maximal and minimal key deliver time, and communication capacity for data collection are presented for various subscriber volume.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.4
• /
• pp.622-630
• /
• 2016

In the operation of a low earth orbit satellite, a series of antenna commands are transmitted from a ground station to the satellite within a visibility window (i.e., the time period for which an antenna of the satellite is visible from the station) and executed to control the antenna. The window is a limited resource where all data transmission is carried out. Therefore, minimizing the transmission time for the antenna commands by reducing the data size is necessary in order to provide more time for the transmission of other data. In this paper, we propose a geometric compression method based on B-spline curve fitting using dominant points in order to compactly represent the antenna commands. We transform the problem of command size reduction into a geometric problem that is relatively easier to deal with. The command data are interpreted as points in a 2D space. The geometric properties of the data distribution are considered to determine the optimal parameters for a curve approximating the data with sufficient accuracy. Experimental results demonstrate that the proposed method is superior to conventional methods currently used in practice.