• 한국항공운항학회지
• /
• 제22권2호
• /
• pp.27-33
• /
• 2014

There are several methods to improve the flight efficiency of HALE(High Altitude Long Endurance) UAV(Unmaned Aerial Vehicle). Airframe structural point of view, weight reduction of the airframe structure is the most important method to improve the flight efficiency. In order to reduce the weight of airframe structures, new concepts which are different from traditional airframe structure design such as the mylar wing skin should be introduced. The spar is the most important component in a mylar skin wing structure, so the spar weight reduction is the key point for reduction of the wing structural weight. In this study, design trade-off study for the front spar of the HALE UAV wing is conducted in order to reduce the weight. Design and analysis procedure of high aspect ratio wing spar are introduced. Several front spar structures are designed and trade-off study regarding the weight and strength for the each spar are performed. Spar design configurations are verified by the static strength test. Finally, optimal front spar design is decided and applied to the HALE UAV wing design.

• 한국수소및신에너지학회논문집
• /
• 제25권2호
• /
• pp.145-150
• /
• 2014

This study investigates the preparation of anti-reflective (AR) coating film to improve the efficiency of solar cell. The AR coating film was successfully obtained by dip-coating with AR coatings prepared by sol-gel method. Fluoroalkylsilane was additionally introduced into the coatings to give the self-cleaning effect of AR coating film. We performed the abrasion test, pencil scratch hardness test and cross-cut test to identify the mechanical strength of AR coating film. As the results, the transmittance of AR coating films with 9.07, 18.13 and 27.20 of IPA/MTMS molar ratios were 93.1, 93.6 and 95.3%, respectively. The water contact angle and transmittance of AR coating film increased by the introduction of hydrophobicity. The prepared AR coating film shows the high level of abrasion, hardness and adhesion. The IPA/MTMS molar ratio of 27.20 and the withdrawing speed range of 0.20 ~ 0.28cm/sec are the optimal coating condition in terms of the transmittance and mechanical strength of AR coating film.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문 발표회
• /
• pp.43-48
• /
• 2003

This paper investigate that the effect of the concrete containing mineral admixtures(pozzolanic materials such as fly-ash, ground granulated blast-furnace slag, silica fume and meta kaolin) on the resistance properties to chloride ion invasion. The purposed testing procedure was applied to the concrete added mineral admixtures for 3~4 replacement ratios under W/B ratios ranged from 0.40 to 0.55. For the electrical migration test, Tang and Nilsson's method was used to estimate the migration coefficient of chloride ion. As a results, the W/B ratios, kinds of admixture and replacement ratios, water curing periods had a great effect on the migration coefficient of chloride ion, and the optimal replacement ratios of admixture had a limitation for each admixtures. Also, the addition of mineral admixtures by mass(replacement of OPC) enhanced the resistance of the mixture to chloride penetration compared with the plain concrete. The amount of acid soluble chloride ions and water soluble chloride ions were varied with the kinds of mineral admixtures. The compressive strength was shown related to the migration coefficient of chloride ion, the compressive strength increased with the decreasing migration coefficient of chloride ion. Below the 50MPa, the variation of migration coefficient of concrete added mineral admixtures was bigger than plain concrete.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문발표회
• /
• pp.43-48
• /
• 2003

This paper investigate that the effect of the concrete containing mineral admixtures(pozzaolanic materials such as fly-ash, ground granulated blast-furnace slag, silica fume and meta kaolin) on the resistance properties to chloride ion invasion. The purposed testing procedure was applied to the concrete added mineral admixtures for 3∼4 replacement ratios under W/B ratios ranged from 0.40 to 0.55. For the electrical migration test, Tang and Nilsson's method was used to estimate the migration coefficient of chloride ion. As a results, the W/B ratios, kinds of admixture and replacement ratios, water curing periods had a great effect on the migration coefficient of chloride ion, and the optimal replacement ratios of admixture had a limitation for each admixtures. Also, the addition of mineral admixtures by mass(replacement of OPC) enhanced the resistance of the mixture to chloride penetration compared with the plain concrete. The amount of acid soluble chloride ions and water soluble chloride ions were varied with the kinds of mineral admixtures. The compressive strength was shown related to the migration coefficient of chloride ion, the compressive strength increased with the decreasing migration coefficient of chloride ion. Below the 50MPa, the variation of migration coefficient of concrete added mineral admixtures was bigger than plain concrete.

• Geomechanics and Engineering
• /
• 제10권5호
• /
• pp.689-707
• /
• 2016

Soil stabilization is one of the useful method of ground improvement for soil with low bearing capacity and high settlement and unrequired swelling potential. Generally, the stabilization is carried out by adding some solid materials. The main objective of this research was to investigate the feasibility of stabilization of organic soils and sewage sludge to obtain low cost alternative embankment material by the addition of two different slags. Slags were used as a replacement for weak soil at ratios of 0%, 25%, 50%, 75% and 100%, where sewage sludge and organic soil were blended with slags separately. The maximum dry unit weights and the optimum water contents for all soil mixtures were determined. In order to investigate the influence of the slags on the strength of sewage sludge and organic soil, and to obtain the optimal mix design; compaction tests, the California bearing ratio (CBR) test, unconfined compressive strength (UCS) test, hydraulic conductivity test (HCT) and pH tests were carried out on slag-soil specimens. Unconfined compressive tests were performed on non-cured samples and those cured at 7 days. The test results obtained from untreated specimens were compared to tests results obtained from soil samples treated with slag. Laboratory tests results indicated that blending slags with organic soil or sewage sludge improved the engineering properties of organic or sewage sludge. Therefore, it is concluded that slag can be potentially used as a stabilizer to improve the properties of organic soils and sewage sludge.

• 한국산학기술학회논문지
• /
• 제14권3호
• /
• pp.991-996
• /
• 2013

본 논문에서는 유리와 구리의 이종재료 접합을 위해 고유진동수를 60 [kHz]로 갖는 초음파 혼을 설계하고자 하였다. 초음파 혼의 입력단과 출력단의 단면비, 혼의 길이 등 관계식을 통해 설정하였으며 설계된 혼의 타당성 분석을 위해 모달해석을 수행하였다. 기초실험을 통하여 공정변수 및 반응변수를 설정하였으며, 초음파 공구 혼을 이용하여 이종재료 접합 강도 실험을 실시하였다. 또한 실험 결과를 통해 최적 공정조건을 도출하였다.

• 한국산학기술학회논문지
• /
• 제16권12호
• /
• pp.8363-8369
• /
• 2015

본 연구에서는 고유동 콘크리트에서 일라이트 미분말을 대체한 콘크리트의 유동성과 충전성 및 압축강도 특성을 조사하기 위한 것이다. 이러한 목적으로 일라이트 미분말을 고유동 콘크리트에 5, 10, 15, 20%를 대체한 후 치환율에 따른 콘크리트의 특성을 알아보았다. 콘크리트 배합 후 굳지않은 콘크리트에서 슬럼프 플로우 시험, 500mm플로우 도달시간 및 O-lot 시험을 실시하였으며, 굳은 콘크리트의 특성으로 재령 28일에 고유동 콘크리트의 압축강도를 측정하였다. 시험결과 고유동 콘크리트의 유동성 및 충전 높이는 일라이트 미분말 10%를 대체하였을 때까지 증가하는 것으로 나타났다. 그리고 고유동 콘크리트의 압축강도 특성을 살펴본 결과에서도 일라이트 미분말 10%를 대체하였을 때까지 강도증진이 발생하였다. 따라서 본 실험결과 일라이트 미분말의 혼입율이 10%일 때 최적 치환율이 되었음을 확인할 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제45권5호
• /
• pp.511-518
• /
• 2017

최근의 단열 재료에 대한 관심과 연구는 단열성능 이외의 복합적 성능을 요구하는 추세이다. 본 연구에서는 구조적인 성능을 가지는 왕겨숯 보드 개발을 위한 목재 섬유대 왕겨숯의 최적 비율을 찾고자 하였다. 왕겨숯을 활용하여 구조적 성능을 지니는 친환경 단열재를 개발하고자 기초 연구를 실시하여 다음과 같은 결론을 얻었다. 최종 왕겨숯 보드의 함수율은 3.2~4.1%로 얻어졌으며, 밀도는 0.58~0.68로 우수한 구조재료로서의 가능성을 보였다. 휨강도는 길이방향으로 9.1-32.6 MPa, 그리고 폭방향으로는 9.2-34.1 MPa로 나타났다. 통상적으로 사용되는 MDF 수준의 휨강도를 얻을 수 있어 구조적 성질을 가지는 단열재 개발의 가능성을 찾을 수 있었다.

• Membrane and Water Treatment
• /
• 제6권3호
• /
• pp.205-224
• /
• 2015

A novel hydrophilic poly (vinylidene fluoride)/poly (p-phenylene terephthalamide) (PVDF/PPTA) blend membrane was prepared by in situ polycondensation of p-phenylene diamine (PPD) and terephthaloyl chloride (TPC) in PVDF solution with subsequent nonsolvent induced phase separation (NIPS) process. For comparison, conventional solution blend membrane was prepared directly by adding PVDF powder into PPTA polycondensation solution. Blend membranes were characterized by means of viscometry, X-ray photoelectron spectroscopy (XPS), Field Emission Scanning Electron Microscopy (FESEM). The effects of different blending methods on membrane performance including water contact angle (WCA), mechanical strength, anti-fouling and anti-compression properties were investigated and compared. Stronger interactions between PVDF and PPTA in in situ blend membranes were verified by viscosity and XPS analysis. The incorporation of PPTA accelerated the demixing rate and caused the formation of a more porous structure in blend membranes. In situ blend membranes exhibited better hydrophilicity and higher tensile strength. The optimal values of WCA and tensile strength were $65^{\circ}$ and 34.1 MPa, which were reduced by 26.1% and increased by 26.3% compared with pure PVDF membrane. Additionally, antifouling properties of in situ blend membranes were greatly improved than pure PVDF membrane with an increasing of flux recovery ratio by 25%. Excellent anti-compression properties were obtained in in situ blend membranes with a stable pore morphology. The correlations among membrane formation mechanism, structure and performance were also discussed.

• 소성∙가공
• /
• 제30권6호
• /
• pp.291-300
• /
• 2021

Currently, starting with electric vehicles, the application of ultra-high-strength steel sheets and light metals has expanded to improve mileage by reducing vehicle weight. At a time when internal combustion engine vehicles are rapidly changing to electric vehicles, the application of ultra-high-strength steel is expanding to satisfy both weight reductions and the performance safety of the chassis parts. There is an urgent need to improve the quality of parts without defects. It is particularly difficult to estimate the part formability through the finite element method (FEM) in the burring operation, so product design has been based on the hole expansion ratio (HER) and experience. In this study, design of experiment (DOE), analysis of variance (ANOVA), and regression analysis were combined to optimize the formability by adjusting the process variables affecting the burring formability of ultra-high-strength steel parts. The optimal variables were derived by analyzing the influence of variables and the correlation between the variables through FE analysis. Finally, the optimized process parameters were verified by comparing experiment with simulation. As for the main influence of each process variable, the initial hole diameter of the piercing process and the shape height of the preforming process had the greatest effects on burring formability, while the effect of a lower round of punching in the burring process was the least. Moreover, as the diameter of the initial hole increased, the thickness reduction rate in the burring part decreased, and the final burring height increased as the shape height during preforming increased.