• 한국광학회지
• /
• 제21권2호
• /
• pp.53-60
• /
• 2010

본 논문에서는 휴대전화용 백라이트 유닛의 광학시트를 줄이면서도 휘도와 휘도균일도 및 시야각을 유지하기 위한 복합 도광판을 설계하고 가공하였다. 복합 도광판의 패턴은 가공성을 고려하여 윗면에는 마이크로 급의 프리즘 패턴을 형성하고 아랫면은 나노 및 마이크로 급의 크기가 다른 두 개의 음각 프리즘 패턴을 형성하였다. 이러한 패턴 형상은 금형 코어를 이용한 사출성형을 통해 복합 도광판의 가공성을 확인하였다. 특히 최적화된 복합 도광판은 프리즘 시트 한 장만을 채용하여 통상적인 백라이트 유닛과 유사한 휘도 4560 cd/$m^2$, 휘도균일도 83%, 수직 시야각 $60^{\circ}$, 수평 시야각 $56^{\circ}$라는 성과를 얻을 수 있었다. 결과적으로 도광판의 윗면과 아랫면에 복합 패턴들을 형성함으로써 기존의 백라이트 유닛에서 확산시트 및 프리즘시트 1장을 제거하여 BLU에 적용될 수 있음을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 추계학술대회논문집
• /
• pp.224-227
• /
• 1997

In Ni and Zn plating, microstructure and corrosion behavior of electrodeposits with various electroplating condition were investigated. Optical microstructure, SEM images and polarization curves of electrodeposits are different with plating time and temperature.

• 한국재료학회지
• /
• 제29권6호
• /
• pp.392-397
• /
• 2019

A cold roll-bonding process is applied to fabricate an AA6061/AA5052/AA6061 three-layer clad sheet. Two AA6061 and one AA5052 sheets of 2 mm thickness, 40 mm width, and 300 mm length are stacked, with the AA5052 sheet located in the center. After surface treatment such as degreasing and wire brushing, sample is reduced to a thickness of 1.5 mm by multi-pass cold rolling. The rolling is performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 400 mm at rolling speed of 6.0 m/sec. The roll bonded AA6061/AA5052/AA6061 complex sheet is then hardened by natural aging(T4) and artificial aging(T6) treatments. The microstructures of the as-roll bonded and age-hardened Al complex sheets are revealed by optical microscopy; the mechanical properties are investigated by tensile testing and hardness testing. After rolling, the roll-bonded AA6061/AA5052/AA6061 sheets show a typical deformation structure in which grains are elongated in the rolling direction. However, after T4 and T6 aging treatment, there is a recrystallization structure consisting of coarse equiaxed grains in both AA5052 and AA6061 sheets. The as roll-bonded specimen shows a sandwich structure in which an AA5052 sheet is inserted into two AA6061 sheets with higher hardness. However, after T4 and T6 aging treatment, there is a different sandwich structure in which the hardness of the upper and lower layers of the AA6061 sheets is higher than that of the center of the AA5052 sheet. The strength values of the T4 and T6 age-treated specimens are found to increase by 1.3 and 1.4 times, respectively, compared to that value of the starting material.

• Journal of the Optical Society of Korea
• /
• 제12권1호
• /
• pp.25-30
• /
• 2008

The optical performances of 15-inch edge-lit backlight were simulated by using a Monte Carlo ray-tracing technique. The backlight model was built by combining a wedge-type light guide plate, a diffuser sheet, a tubular fluorescent lamp with a lamp reflector, and two crossed prism sheets. Angular distributions of the luminance on each optical component obtained from simulation were consistent with those obtained from experiments on a real 15-inch backlight. The constructed backlight model was used to evaluate the optical performances of a micro-pyramid film. It was found that the on-axis luminance gain on the pyramid film is higher than that on one prism film but much lower than that on the two crossed prism films. These results suggest that a reliable simulation model can be used to develop new hybrid films and to optimize the optical structure of edge-lit backlight in order to reduce the developmental period.

• 한국광학회지
• /
• 제30권6호
• /
• pp.230-236
• /
• 2019

저렴한 retro-반사지와 미소 전자 기계 시스템(micro electro-mechanical system, MEMS) 거울을 이용한 실내용 무선 광 통신용 위치 탐색 및 자동 링크 정렬 방법을 제안하고 실험하였다. 직접적인 가시선(line of sight, LOS) 확보를 위하여 retro-반사지에서 돌아온 빛으로부터 수신단 위치를 파악하고 MEMS 거울을 통한 빔 조종으로 통신 링크를 자동 정렬하였다. 자동 정렬된 광 링크를 통하여 7 m 전송 거리에서 2.5 Gb/s NRZ 신호를 전송하여 비트 에러율 10^-12에서 수신 감도 -31.87 dBm의 성능을 가졌다.

• 대한토목학회논문집
• /
• 제42권3호
• /
• pp.311-322
• /
• 2022

본 연구에서는 분포형 광섬유 시트와 탄소섬유 시트를 콘크리트 표면에 부착하여 철근 콘크리트를 사용하는 구조물의 보강 효과 및 BOTDR 센서를 활용한 상태 평가를 4점 휨 실험을 통해 수행하였다. 부착 정도에 따른 보강 효과를 확인하기 위하여 탄소섬유 시트의 부착 형태를 다양하게 제작하였으며, BOTDR 센서의 활용성을 확인하기 위하여 실험체에 다수의 전기저항식 변형률 게이지를 부착하여 BOTDR 센서의 변형률과 비교하였다. 실험 결과를 살펴보면, 우선 CFRP시트 부착 정도에 따른 보강 효과에 분명한 차이가 나타나는데, 이는 부착 면적보다는 부착 형태에 더 영향을 받는 것으로 확인되었다. BOTDR 센서로부터 계측된 변형률로부터 하중 증가에 따른 철근 콘크리트 실험체의 구조적 거동을 시각화 할 수 있었으며, CFRP 보강 부위에서 하중이 집중되는 것을 알 수 있다. BOTDR 센서에서 계측된 변형률이 전기저항식 게이지로부터 계측된 변형률과 유사하게 계측되는 것을 알 수 있는데, 이를 통해 대형 토목 구조물의 전체적 거동을 분석하는데 BOTDR 센서가 효과적일 수 있음을 확인하였다. 다시 말해서, 국부적 변형률을 측정하는 전기식 변형률 게이지로 계측을 하면 계측 오차는 상당할 수 있는 반면에, 분포형으로 측정되는 BOTDR 센서는 이러한 문제를 줄일 수 있는 대안으로 판단된다. 마지막으로, CFRP 시트 탈락이 발생되는 부분에서 계측 BOTDR 센서 변형률이 높게 나타나는데 이를 활용하면 CFRP 시트의 국부적 손상 위치를 효율적으로 추적할 수 있을 것으로 판단된다.

• Transactions on Electrical and Electronic Materials
• /
• 제10권5호
• /
• pp.169-172
• /
• 2009

The ZnO/CuSn/ZnO (ZCSZ) multilayer films were deposited on polycarbonate substrates using reactive RF and DC magnetron sputtering. The thickness of each layer was 50 nm/5 nm/45 nm, respectively. The ZCSZ films showed a sheet resistance of $44{\Omega}$/Sq, which was an order of magnitude lower than that indium tin oxide (ITO) films. Although the ZCSZ films had a CuSn interlayer that absorbed visible light, both films had similar optical transmittances of 74% in the visible wavelength region. The figure of merit of the ZCSZ films was $1.0{\times}10^{-3}{\Omega}^{-1}$ and was greater than the value of the ITO films, $1.6{\times}10^{-4}{\Omega}^{-1}$. From the X-ray diffraction (XRD) analysis, the ITO films did not show any diffraction peaks, whereas the ZCSZ films showed diffraction peaks for the ZnO (100) and (002) phases. The hardness of the ITO and ZCSZ films were 5.8 and 7.1 GPa, respectively, which were determined using nano-indentation. From these results, the ZCSZ films exhibited greater optoelectrical performance and hardness compared to the conventional ITO films.

• 한국전기전자재료학회논문지
• /
• 제19권12호
• /
• pp.1134-1139
• /
• 2006

Electrical, optical, and structural properties of indium zinc oxide (IZO) anode films grown by a RF magnetron sputtering were investigated as functions of RF power and working pressure in pure Ar ambient. To investigate electrical, optical and structural properties of IZO anode films, 4-point probe and UV/VIS spectrometry, and X-ray diffraction (XRD) were performed, respectively. A sheet resistance of $15.2{\Omega}/{\square}$, average transmittance above 80 % in visible range, expecially above 85 % in 550 nm, and root mean square roughness of 1.13 nm were obtained from optimized IZO anode films grown in oxygen free ambient. All samples show amorphous structure regardless of RF power and working pressure due to low substrate temperature. In addition, XPS depth profile obtained from IZO/PES exhibits that there is no obvious evidence of interfacial reaction between IZO and PES substrate. Furthermore, current-voltage-luminance of the flexible phosphorescent flexible OLEDs fabricated on IZO anode shows dependence on sheet resistance of the IZO anode. These results indicate that the IZO anode is a promising candidate to substitute conventional ITO anode for high-quality flexible displays.

• 한국전기전자재료학회논문지
• /
• 제23권4호
• /
• pp.261-266
• /
• 2010

In this paper, we report the changes of electrical, structural and optical characteristics in $Ge_2Sb_2Te_5$ thin films according to an increase of Si content. The Si-doped $Ge_2Sb_2Te_5$ thin films were prepared by rf-magnetron co-sputtering method. Isothermal annealing was carried out at $N_2$ atmosphere. The crystallization speed (v) of amorphous thin films was evaluated by detecting the reflection response signals using a nano-pulse scanner (wavelength = 658 nm) with illumination power of 1~17 mW and pulse duration of 10~460 ns. Structural phase changes were evaluated by XRD, and the optical transmittance was measured in the wavelength range of 300~3000 nm using UV-vis-NIR spectrophotometer. The sheet resistance (RS) of the thin films was measured using 4 point probe. Conclusivlely, the v-value decreased with an increase of Si content, while the RS-values of both crystalline and amorphous phases were increased. In particular, fcc-to-hexagonal transition was suppressed by the added Si atoms.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.137-140
• /
• 2004

We treated $O_2$ plasma on ITO thin film using RIE (Reactive Ion Etching) system, and analyzed the ingredient of ITO thin film according to change of processing conditions. The ingredient analysis of ITO thin film was used by EDS (Energy Dispersive Spectroscopy) and XPS (X-ray Photoelectron Spectroscopy) to compare and analyze the ingredient of bulk and surface. We measured electrical resistivity using Four-Point-Probe and calculated sheet resistance, and ITO surface roughness was measured by using AFM (Atomic Force Microscope). Finally, we fabricated OLEDs (Organic Light-Emitting Diodes) device using substrate that was treated optimum ITO surface. The result of the study for electrical and optical properties using I V L System (Flat Panel Display Analysis System), we confirmed that electrical properties (I-V) and optical properties (L-V) were improved.