• Korean Journal of Optics and Photonics
• /
• v.8 no.1
• /
• pp.31-36
• /
• 1997

We measured refractive indices and thicknesses of SiO$_2$ thin films that have been plated on LCD glass substrate for the purpose of preventing the out-diffusion of sodium ions. The best experimental condition to determine refractive index and thickness of SiO$_2$ thin film by using ellipsometry is searched for, where ⅰ) the film thickness is increased uniformly by 20 $\AA$ from 0 $\AA$ to the period thickness while the angle of incidence is fixed and ⅱ) the angle of incidence is increased uniformly by 1$^{\circ}$ from 45$^{\circ}$ to 70$^{\circ}$ while the film thickness is fixed. We estimated the errors in determining the refractive index and thickness by comparing the measurement error of $\Delta$ and Ψ with the calculated one. The ellipsometric constants of SiO$_2$ thin film on LCD glass substrate are measured at several angle of incidence around the Brewster angle, which is the best angle if the experimental error of ellipsometer is not sensitive to the incident angle. Also the best fit refractive index and thickness of SiO$_2$ thin film to these ellipsometric constants measured at several angle of incidenc eas well as the best fit ones to the SE data are obtained using regressional analysis.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.248-253
• /
• 2005

We designed and fabricated a compact multi-mode interference (MMI) wavelength demultiplexer using the concept of 'Improved Quasi-State' modes. The output power and extinction ratio were improved by utilizing modal phase error which is specially occurred in low-index contrast. For a designed demultiplexer, the mode propagation analysis with effective index approximation shows significant improvement of extinction ratio to -25 dB for both $1.31{\mu}m\;and\;1.51{\mu}m$ wavelength region and the split-length was reduced about 1/5 of other MMI devices. The fabricated device shows successful characteristics for both 1.31 and $1.55{\mu}m$ wavelengths. These results demonstrate the potential of low-index materials system and the embossing process for photonic integrated circuits.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.505-512
• /
• 2014

A new donor-accepter-donor-accepter-donor (D-A-D-A-D) type 2,1,3-benzothiadiazole-thiophene-based acceptor unit 2,5-di(4-(5-bromo-4-octylthiophen-2-yl)-2,1,3-benzothiadiazol-7-yl)thiophene ($DTBTTBr_2$) was synthesized. Copolymerized with fluorene and indeno[1,2-b]fluorene electron-rich moieties, two alternating narrow band gap (NBG) copolymers PF-DTBTT and PIF-DTBTT were prepared. And two copolymers exhibit broad and strong absorption in the range of 300-700 nm with optical band gap of about 1.75 eV. The highest occupied molecular orbital (HOMO) energy levels vary between -5.43 and -5.52 eV and the lowest unoccupied molecular orbital (LUMO) energy levels range from -3.64 to -3.77 eV. Potential applications of the copolymers as electron donor material and $PC_{71}BM$ ([6,6]-phenyl-$C_{71}$ butyric acid methyl ester) as electron acceptors were investigated for photovoltaic solar cells (PSCs). Photovoltaic performances based on the blend of PF-DTBTT/$PC_{71}BM$ (w:w; 1:2) and PIF-DTBTT/$PC_{71}BM$ (w:w; 1:2) with devices configuration as ITO/PEDOT: PSS/blend/Ca/Al, show an incident photon-to-current conversion efficiency (IPCE) of 2.34% and 2.56% with the open circuit voltage ($V_{oc}$) of 0.87 V and 0.90 V, short circuit current density ($J_{sc}$) of $6.02mA/cm^2$ and $6.12mA/cm^2$ under an AM1.5 simulator ($100mA/cm^2$). The photocurrent responses exhibit the onset wavelength extending up to 720 nm. These results indicate that the resulted narrow band gap copolymers are viable electron donor materials for polymer solar cells.

• The Korean Journal of Mycology
• /
• v.10 no.2
• /
• pp.57-65
• /
• 1982

Highly phosphorylated nucleotides were investigated to assure whether the eucaryotic Aspergillus niger produce these substances or not during the differentiation. Investigation was extended to see how organic phosphate interacts with inorganic polyphosphate during development, and high molecular weight RNA-polyphosphate complex was detected in 2.6% polyacrylamide gel by electrophoresis. Guanosine tetraphosphate was found in vesicle and phialide forming mycelia and spore forming body by PEI cellulose TLC. It is revealed that guanosine tetraphosphate is a common substance for spore formation in eucaryotic microorganisms as well as in procaryotic. Especially, prior to sporulation, protein bound RNA and protein bound phosphate may occur as a result of reorganization of cellular materials. The evidence was obtained by the fact of differential increase of optical density ratio between the samples from different developmental stages of this fungus. In 2.6% polyacrylamide gel which was run to electrophoresis, high molecular weight RNA (mostly rRNA) was found to couple and to make RNA-polyphosphate complex. The complex was examined with enzymes and radioactive isotope of $^{32}P$. (enzymic test was not reported here.) RNA-polyphosphate complex might be another sort of highly phosphorylated nucleotide or rRNA beside guanosine-tetraphosphate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.588-588
• /
• 2013

Nanoscale noble-metals have attracted enormous attention from researchers in various fields of study because of their unusual optical properties as well as novel chemical properties. They have possible uses in diverse applications such as devices, transistors, optoelectronics, information storages, and energy converters. It is well-known that nanoparticles of noble-metals such as silver and gold show strong absorption bands in the visible region due to their surface-plasmon oscillation modes of conductive electrons. Silver nanocubes stand out from various types of Silver nanostructures (e.g., spheres, rods, bars, belts, and wires) due to their superior performance in a range of applications involvinglocalized surface plasmon resonance, surface-enhanced Raman scattering, and biosensing. In addition, extensive efforts have been devoted to the investigation of Gold-based nanocomposites to achieve high catalytic performances and utilization efficiencies. Furthermore, as the catalytic reactivity of Silver nanostructures depends highly on their morphology, hollow Gold nanoparticles having void interiors may offer additional catalytic advantages due to their increased surface areas. Especially, hollow nanospheres possess structurally tunable features such as shell thickness, interior cavity size, and chemical composition, leading to relatively high surface areas, low densities, and reduced costs compared with their solid counterparts. Thus, hollow-structured noblemetal nanoparticles can be applied to nanometer-sized chemical reactors, efficient catalysts, energy-storage media, and small containers to encapsulate multi-functional active materials. Silver nanocubes dispersed in water have been transformed into Ag@Au nanoboxes, which show highly enhanced catalytic properties, by adding $HAuCl_4$. By using this concept, $SiO_2$-coated Ag@Au nanoboxes have been synthesized via galvanic replacement of $SiO_2$-coated Ag nanocubes. They have lower catalytic ability but more stability than Ag@Au nanoboxes do. Thus, they could be recycled. $SiO_2$-coated Ag@Au nanoboxes have been found to catalyze the degradation of 4-nitrophenol efficiently in the presence of $NaBH_4$. By changing the amount of the added noble metal salt to control the molar ratio Au to Ag, we could tune the catalytic properties of the nanostructures in the reduction of the dyes. The catalytic ability of $SiO_2$-coated Ag@Au nanoboxes has been found to be much more efficient than $SiO_2$-coated Ag nanocubes. Catalytic performances were affected noteworthily by the metals, sizes, and shapes of noble-metal nanostructures.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.1
• /
• pp.7-11
• /
• 2010

The reduction of optical losses in mono-crystalline silicon solar cell by surface texturing is a critical step to improve the overall cell efficiency. In this study, we have changed the sub-micrometer structure on the micrometer pyramidal structure by 2-step texturing. The Ag particles were coated on the micrometer pyramid surface in $AgNO_3$ solution, and then the etching with hydrogen fluoride and hydrogen peroxide created even smaller nano-pyramids in these pyramids. As a result, we observed that the changes of size and thickness of nano structure on pyramidal surface were determined by $AgNO_3$ concentration and etching time. Using 2-step texturing, the surface of wafers is etched to resemble the rough surface of a lotus leaf. Lotus surface can reduce average reflectance from 10% to below 3%. This reflectance is less than conventional textured wafer including anti-reflection coating.

• Journal of Periodontal and Implant Science
• /
• v.28 no.2
• /
• pp.337-350
• /
• 1998

The purpose of this' study was to compare surface roughness and morphologic changes after use of various plaque control devices to titanium implant surfaces. The study materials were 6 ITI titanium implants($Bonefit^{(R)}$) and 5 plaque control devices. 6 implants were divided into 6 different groups and instrumented by each plaque control devices as follows. 1) Group I : untreated control 2) Group II : Titanium curette(Titanium $curette^{(R)}$, 3i) 80 vertical/horizontal strokes 3) Group III : Plastic curette($Implacare^{(R)}$, Hu-Friedy) 80 vertical/horizontal strokes 4) Group N : Plastic tip-ultrasonic scaler($Amdent^{(R)}$, Amdent) 160 seconds 5) Group V : Rotating interdental brush($Identobrush^{(R)}$, Identoflex) 160 seconds 6) Group VI : Abrasive rubber cup polisher($Zircate^{(R)}$, Prophy paste, Dentsply) 160 sec-onds. All specimens were prepared for evaluation by surface roughness tester, optical stereomicroscopy(OM) and scanning electron microscopy(SEM). The Ra and Rt mean values of the tested specimens were 1) Group I ($Ra=0.170{\pm}0.007{\mu}m$, $Rt=1.297{\pm}0.016{\mu}m$) 2) Group II ($Ra=0.209{\pm}0.006{\mu}m$, $Rt=1.602{\pm}0.110{\mu}m$) 3) Group III ($Ra=0.179{\pm}0.001{\mu}m$, $Rt=1.429{\pm}0.055{\mu}m$) 4) Group IV ($Ra=0.182{\pm}0.005{\mu}m$, $Rt=1.511{\pm}0.085{\mu}m$) 5) Group V ($Ra=0.301{\pm}0.008{\mu}m$, $Rt=1.882{\pm}0.131{\mu}m$) 6) Group VI ($Ra=0.147{\pm}0.010{\mu}m$, $Rt=1.059{\pm}0.021{\mu}m$) In Ra values, experimental group II, V, VI were statistically significant different when compared with control. OM and SEM observation showed that experimental group III, IV were minimal changes when compared with control and group VI was smoothest among other experimental groups. The results suggested that plastic curette and plastic tip-ultrasonic scaler were predictable devices to titanium implant surface.

• Journal of Periodontal and Implant Science
• /
• v.35 no.4
• /
• pp.939-948
• /
• 2005

The role of the periosteum on osteointegration of $Bio-Oss^{(R)}$(Geistlich, Wolhusen/Switzerland) was studied in rabbit calvarial defect. 12 New Zealand white male rabbits between 2.8 and 4 kg were included in this randomized, blinded, prospective study. Each rabbit was anesthetized with Ketamine HCl(5 mg/kg) and Xylazine HCl(1.5 ml/kg). An incision was made to the bony cranium and the periosteum was reflected. Using a 6-mm trephine bur(3i. USA), four 8-mm defects were created with copious irrigation. The defects were classified into barrier membrane($Tefgen^{(R)}$, Lifecore Biomedical. Inc, U.S.A.) only group as a control, $Bio-Oss^{(R)}$ with barrier membrane group, $Bio-Oss^{(R)}$ with periosteum covering group, and $Bio-Oss^{(R)}$ without periosteum covering group. There were 2 rabbits in each group. The wound was closed with resorbable suture materials. Rabbits were sacrificed using phentobarbital(100 mg/kg) intravenously at 1, 2, and 4 weeks after surgery. The samples were fixed in 4% paraformaldehyde, and decalcified in hydrochloric acid decalcifying solution(Fisher Scientific, Tustin, CA) at $4^{\circ}C$ for 2-4 weeks. It was embedded in paraffin and cut into 6 ${\mu}m$ thickness. The sections were stained with H & E and observed by optical microscope. The results were as follows; 1. The periosteum played an important role in osteointegration of $Bio-Oss^{(R)}$ in bone defects. 2. When the periosteum remained intact and $Bio-Oss^{(R)}$ was placed on the defect, $Bio-Oss^{(R)}$ with periosteum covering has been incorporated into the newly formed bone from 2-week postoperatively. 3. When the periosteum was removed at the surgical procedure, invasion of connective tissue took place among the granules, and new bone formation was delayed compared to periosteum covering group. Therefore, when the bone grafting was performed with periosteal incision procedure to achieve tension-free suture, the integrity of the overlying periosteum should be maintained to avoid fibrous tissue ingrowth.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.3
• /
• pp.382-388
• /
• 2007

Statement of problem. The role of calcium sulfate in stimulating the growth of gingival soft tissue has been reported in few studies. Such a unique property of calcium sulfate could serve as a trouble-solving broker in compensating for the lack of soft tissues in various oral surgeries. Purpose. The purpose of this study was to compare the proliferating activities of human gingival fibroblasts seeded on various bone graft barrier materials of calcium sulfate, collagen, and polytetrafluorethylene (PTFE). Material and methods. Two calcium sulfates ($CAPSET^{(R)}$. and $CalForma^{(R)}$, Lifecore Biomedical Inc., St. Paul, Minnesota, USA), a resorbable natural collagen ($Bio-Gide^{(R)}$, Geistlich Pharma Ag., Wolhusen, Switzerland), and a non-resorbable PTFE ($TefGen-FD^{(R)}$, Lifecore Biomedical Inc., St. Paul, Minnesota, USA) served as the human gingival fibroblasts' substrates and comprised the four experimental groups, whereas the untreated floors of culture plastics were used in the control group, in this study. Cells were trypsinized, seeded, and incubated for 48 h. The proliferating activities of fibroblasts were determined by XTT and SRB assay and absorbance (optical density, OD) was measured. One-way ANOVA was used to analyze the differences in the mean OD values between the groups of CAPSET, CalForma, Bio-Gide, TefGen, and the control (p<0.05). Results. From the XTT assay, the mean OD value of the control group, the highest, was significantly greater than that of any of the four experimental groups followed by CalForma, CAPSET, TefGen, and Bio-Gide. Further, the mean OD value of CalForma, was significantly greater compared to that of Bio-Gide. From the SRB assay, Calforma showed the highest mean OD value, which was significantly greater than that of any other groups, followed by the control, CAPSET, Bio-Gide, and TefGen. The mean OD values of both the control and CAPSET were significantly greater compared to that of TefGen (p<0.05). Conclusion. Assessment of the viability and proliferation of cultured fibroblasts seeded and incubated for 48 h on various barrier-material substrates using XTT and SRB assay showed that calcium sulfate $CalForma^{(R)}$ promotes the proliferating activity of human gingival fibroblasts.

• Journal of Periodontal and Implant Science
• /
• v.50 no.4
• /
• pp.238-250
• /
• 2020

Purpose: This study aimed to evaluate the biocompatibility and the mechanical properties of ultraviolet (UV) cross-linked and biphasic calcium phosphate (BCP)-added collagen membranes and to compare the clinical results of ridge preservation to those obtained using chemically cross-linked collagen membranes. Methods: The study comprised an in vitro test and a clinical trial for membrane evaluation. BCP-added collagen membranes with UV cross-linking were prepared. In the in vitro test, scanning electron microscopy, a collagenase assay, and a tensile strength test were performed. The clinical trial involved 14 patients undergoing a ridge preservation procedure. All participants were randomly divided into the test group, which received UV cross-linked membranes (n=7), and the control group, which received chemically cross-linked membranes (n=7). BCP bone substitutes were used for both the test group and the control group. Cone-beam computed tomography (CBCT) scans were performed and alginate impressions were taken 1 week and 3 months after surgery. The casts were scanned via an optical scanner to measure the volumetric changes. The results were analyzed using the nonparametric Mann-Whitney U test. Results: The fastest degradation rate was found in the collagen membranes without the addition of BCP. The highest enzyme resistance and the highest tensile strength were found when the collagen-to-BCP ratio was 1:1. There was no significant difference in dimensional changes in the 3-dimensional modeling or CBCT scans between the test and control groups in the clinical trial (P>0.05). Conclusions: The addition of BCP and UV cross-linking improved the biocompatibility and the mechanical strength of the membranes. Within the limits of the clinical trial, the sites grafted using BCP in combination with UV cross-linked and BCP-added collagen membranes (test group) did not show any statistically significant difference in terms of dimensional change compared with the control group.