• ETRI Journal
• /
• v.27 no.4
• /
• pp.446-448
• /
• 2005

Using tightly focused femtosecond laser pulses, we produce an optical waveguide and devices in transparent materials. This technique has the potential to generate not only channel waveguides, but also three-dimensional optical devices. In this paper, an optical splitter and U-grooves, which are used for fiber alignment, are simultaneously fabricated in a fused silica glass using near-IR femtosecond laser pulses. The fiber- aligned optical splitter has a low insertion loss, less than 4 dB, including an intrinsic splitting loss of 3 dB and excess loss due to the passive alignment of a single-mode fiber. Finally, we present an output field pattern, demonstrating that the splitting ratio of the optical splitter becomes approximately 1:1.

• Korean Journal of Optics and Photonics
• /
• v.15 no.2
• /
• pp.104-108
• /
• 2004

A simple dispersion measurement technique has been demonstrated by using a self-seeding laser oscillation of a Fabry-Perot laser through a closed loop. The optical pulses of different wavelengths emitted from the Fabry-Perot laser travel down an optical fiber and the group velocity difference between the pulses due to the chromatic dispersion of the optical fiber is measured through the self-seeding laser oscillation process. The dispersion parameter of the optical fiber is calculated from the measured group velocity difference. The performance of the proposed technique has been confirmed experimentally and the accuracy of dispersion parameter measurement was comparable to that of commercial instruments with expensive equipment and components. The repeatability of the proposed method was better than 0.5%.

• Proceedings of the Korean Reliability Society Conference
• /
• 2004.07a
• /
• pp.147-151
• /
• 2004

In this study, an optical fiber assembly directly coupled with a laser diode or a photo diode is designed to confirm high reliable optical coupling efficiency of optical transmitter(Tx) and receiver(Rx). The optical fiber assembly is fabricated by soldering an optical fiber and a Kovar ferrule using a glass solder after inserting an optical fiber through a Kovar ferrule. The Kovar which has good welding characteristics is applied to introduce laser welding technique. The glass solder has excellent thermal characteristics such as thermal shift delamination compared with PbSn, AuSn solder previously used usually. Furthermore, the glass solder doesn't need fiber metalization and this enables low cost fabrication. However, the glass soldering is high temperature process over 35$0^{\circ}C$ and the convex shape after solidification due to surface tension causes the stress concentration on optical fiber. The stress concentration on the optical fiber increases the optical insertion loss and possibility of crack formation. The shape of glass solder was designed referring to 2-D Axi-symmetric FEM simulation. To test the mechanical reliability, mechanical vibration test and shock test were done according to Telcorida GR-468-Core protocol. After each test, the optical loss of the stress distributed fiber assembly didn't exceed 0.5 dB, which passes the test.

• Current Optics and Photonics
• /
• v.4 no.3
• /
• pp.221-228
• /
• 2020

We developed an all-fiber RGB laser light source module for application in an automobile head-up display. It is based on laser diodes and an optical fiber combiner that substantially enhances the flexibility of configuration and stability against harsh working conditions for automobiles. We coupled 13 laser diodes with optical fibers and merged them into a single output with a beam combiner device. Red (R), green (G), and blue (B) laser sources were employed to produce primary colors that were mixed into a white light output. An optical output power of approximately 1.5 W was achieved, and the color balance of the output lights was assessed based on the CIE 1931 color space. The optical output power was shown to be stable for over 160 h within an optical fluctuation of less than 0.27%.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.135-139
• /
• 2017

In recent years, the optical fiber laser has been widely used in industrial fields due to its excellent economical efficiency and its suitability for industrial applications. This usage has increased even further since the KW class Laser was developed. In this paper, structural analysis and heat transfer analysis of a 500W class optical fiber laser end cap module was performed. The stability of end cap housing with the efficient heat dissipation structure of a 500W-class end cap was evaluated. This research determined the optimal design that should be applied to the design and evaluation of future KW class laser output modules.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.135-139
• /
• 2016

I propose a vector passive harmonic mode-locked fiber laser based on topological insulator Bi2Se3 interacting with a fiber taper with a diameter of 7 μm. The particles of topological insulator are deposited uniformly onto the fiber taper with light pressure effect. By incorporating the fabricated saturable absorber into an Er-doped fiber laser cavity, stable mode-locked fiber is obtained. Due to the intense evanescent field of the fiber taper, strong confinement of light enhances the nonlinearity of the laser cavity, and passive harmonic mode-locking is performed. I observe a maximum harmonic mode-locking of 356th, corresponding to a frequency of 3.57 GHz. The pulse duration is 824 fs, and the full width at half maximum of the spectrum is about 8.2 nm. The polarization dependent loss of the saturable absorber is ~ 2.5 dB in the wavelength range of the C band. As the cavity contains no other polarization dependent device, the mode-locked laser is functioning in the vector state. The harmonic order vs pump power is investigated. To the best of our knowledge, this report is the highest frequency mode-locked fiber laser based on Bi2Se3. Experimental results indicate that the topological insulator Bi2Se3 functioning with a thin fiber taper is effective for vector harmonic mode-locking.

• Journal of the Optical Society of Korea
• /
• v.17 no.4
• /
• pp.312-316
• /
• 2013

A novel fiber-optic sensor system is suggested in which fiber Bragg grating sensors are demodulated by a wavelength-sweeping fiber laser source and a spectrometer. The spectrometer consists of a diffraction grating and a 512-pixel photo-diode array. The reflected Bragg wavelength information is transformed into spatial intensity distribution on the photo-diode array. The peak locations linearly correspond to the Bragg wavelengths, regardless of the nonlinearities in the wavelength tuning mechanism of the fiber laser. The high power density of the fiber laser enables obtaining high signal-to-noise ratio outputs. The improved demodulation characteristics were experimentally demonstrated with a fiber Bragg grating sensor array with 5 gratings. The sensor outputs were in much more linear fashion compared with the conventional tunable band-pass filter demodulation. Also it showed advantages in signal processing, due to the high level of photo-diode array signals, over the broadband light source system, especially in measurement of fast varying dynamic physical quantities.

• Korean Journal of Optics and Photonics
• /
• v.16 no.5
• /
• pp.406-410
• /
• 2005

we propose an external cavity laser which can adjust the number of longitudinal laser mode by using a tunable chirped fiber. Bragg grating. By inducing a tunable temperature gradient in a uniform fiber Bragg grating, the bandwidth of the unform fiber Bragg grating can be tuned. With the chirped fiber Bragg grating as an external reflector of the external cavity laser, the number of longitudinal laser mode was able to be tuned from one to two or three modes.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.3
• /
• pp.277-282
• /
• 2016

Effect of spectral drift in coherent fiber laser was investigated by injecting optical feedback to Fabry-Perot resonance loop. Er+3 doped fiber laser having unilateral optical feedback loop in Fabry-Perot configuration using two FBGs was fabricated. The optical feedback was found to be effective in linewidth reduction of fiber laser compared to the case without any optical feedback. The linewidth of three fiber lasers using above configuration were measured to be within 3kHz which is resolution-limited performance of self-heterodyne linewidth measurement set-up. The frequency drift measurement using Mach-Zehnder measurement set-up having 200m optical delay-line in one arm showed that the frequency drift rate of optical feedback fiber laser was measured as 300kHz/sec which was better than the case without optical feedback.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.12
• /
• pp.2214-2216
• /
• 2007

Based on a semiconductor optical amplifier and sampled fiber Bragg gratings, polarization-controlled waveband switching in multiwavelength fiber laser is successfully demonstrated at room temperature by using high polarization selectivity of a polarization beam splitter. A multiwavelength-switching operation between eight and six laser lines with signal to noise ratio over 35 dB and wavelength spacing of ${\sim}0.8nm$ has been successfully demonstrated. The switching displacement of the proposed laser was ${\sim}7.1nm$. The intensity unevenness between different laser lines was measured to be less than 6.5 dB. The switching displacement between wavebands (groups of contiguous wavelengths), wavelength channels, and their spacings can be flexibly designed by the selected comb filters.