• Proceedings of the Optical Society of Korea Conference
• /
• 2002.11a
• /
• pp.52-53
• /
• 2002

• Journal of IKEEE
• /
• v.13 no.1
• /
• pp.65-70
• /
• 2009

We propose an ultrashort pulse optical code-division multiple-access (O-CDMA) scheme based on a pseudorandom binary M-sequence spectral phase encoding and decoding of coherent mode-locked laser pulses and perform a numerical simulation to analyze its feasibility. We demonstrate the ability to properly decode any of the multiple (eight) 10 Gbit/s users by the matched code selection of the spectral phase decoder. The peak power signal to noise ratio of properly and improperly decoded $8{\times}10 Gb/s$ signals could be greater than 15 for 127 M-sequence coding.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.2 s.15
• /
• pp.7-10
• /
• 2006

The detailed studies regarding to the front and rear panel geometries of plasma display were needed to improve the luminance and efficiency. In plasma displays, 3-dimensional optical code can be used to analyze the variation of geometries and the changing of optical properties. The visible light distributions and illuminance were simulated depending on bus electrode position, ITO geometries, and alteration of dielectric layer's properties. This paper is concerned with development of a cell having high luminance and high efficiency for optical simulation. And the result of values could be expected to the application of real POP cell.

• Journal of Communications and Networks
• /
• v.4 no.3
• /
• pp.170-175
• /
• 2002

An optical fiber code-division multiple-access (CDMA) network is proposed in which encoding is based on the use of concatenated sequences of relatively large weight. The first short component sequence in the concatenated sequence permits realistic electronic encoding of each data bit. The chips of this sequence are then all-optically encoded at substantially higher rate. In spite of the relatively large weight of the sequence the all-optical encoder is practical by virtue of the shortness of the component sequences. The use of Gold and Lempel sequences as component sequences for generating the concatenated sequences is studied and the bit-error rate (BER) performance of the proposed system is presented as a function of the received optical power with the number of simultaneous users as parameter.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.11
• /
• pp.19-28
• /
• 2003

The limitation on the dynamic range improvement of the complementary correlation optical time domain reflectometer(CCOTDR) is presented. In CCOTDR, the improvement of dynamic range is function of both the averaging number of measurement cycles and the length of codes. The trade off between the averaging number and the code length restricts the improvement of the dynamic range and a very long code is not effective to improve the dynamic range. In this paper, the improvement limitation on dynamic range caused by the trade off between the averaging number and the code length is presented. For derivation of the trade off, the number of one measurement cycles employing a conventional single pulse method and employing a complementary code method are presented and compared. And the effective maximum code length is presented in addition.

• The Transactions of the Korea Information Processing Society
• /
• v.1 no.4
• /
• pp.479-489
• /
• 1994

At the present time, it is an important problem that we are to select a transmission line code for the very-high speed optical transmission system which can confidentially transfer the original information signal sequence efficiently, as it is to be the large capacity and the economization for the optical digital transmission system to transfer the information signal sequence at the very-high speed. Therefore, this paper is to select first the proper transmission line codes for the high speed(more than Mb/s) optical transmission system of the proposed two-level unipolar transmission line codes up to date, and to decide a mBIZ (m Binary with One Zero insertion) code as an optimal transmission line code for the very-high speed optical transmission system, resulting from analyzing the performance at the requirements of the transmission line code, such as the maximum consecutive identical digits, the transmission delay time, the increasing rate of clock, the mark rate, the circuit complexity, the supervision of transmission line error, and power spectrum among the selected transmission line codes.

• Korean Journal of Optics and Photonics
• /
• v.33 no.3
• /
• pp.106-112
• /
• 2022

A two-dimensional optical code division multiple access (OCDMA) encoder/decoder, which is composed of add/drop filters and all-pass filters for delay operation, is proposed. An example design is presented, and its feasibility is illustrated through numerical simulations. The chip area of the proposed OCDMA encoder/decoder could be about one-third that of a previous OCDMA device employing delay waveguides. Its performance is numerically investigated using the transfer-matrix method combined with the fast Fourier transform. The autocorrelation peak level over the maximum cross-correlation level for incorrect wavelength hopping and spectral phase code combinations is greater than 3 at the center of the correctly decoded pulse, which assures a bit error rate lower than 10^-3, corresponding to the forward error-correction limit.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.2013-2014
• /
• 2006

For large capacity optical CDMA networks, we propose a shared-type encoder/decoder based on an tunable wavelength conveter (TWC) and an arrayed waveguide grating (AWG) router. Feasibility of the structure of the proposed encoder/decoder for dynamic code allocation is tested through simulations using three types of wavelength/time 2-D codes, which are the generalized multi-wavelength prime code(GMWPC), the generalized multi-wavelength Reed-Solomon code(GMWRSC) and the matrix code. Test results show that the proposed encoder/decoder can increase the channel efficiency not only by increasing the number of simultaneous users without any multiple-access interference but by using a relatively short length CDMA codes.

• Journal of the Korean Ceramic Society
• /
• v.56 no.5
• /
• pp.421-434
• /
• 2019

We face many fascinating and diverse challenges, the most important among which is to determine how to store a large amount of information with novel approaches. Info-convergence ceramic nanosystems, which combine ceramic materials science and information technology, may provide an attractive alternative. This review considers recent multidisciplinary advances in the development of info-convergence nanosystems based on ceramic materials and discusses various strategies under ceramic-based information systems with a special focus on materials and nanohybridization technologies. Ceramic materials have played diverse roles not only as the generic coding support, but also as the central coding substance. The review highlights the ceramic nanohybrid bio code and ceramic nanoparticle optical code for applications in tracking-and-traceability management, nano-forensics, anti-counterfeiting, and even communication, as well as the four steps of encoding, encrypting, decrypting, and decoding for the desired applications. Additionally, associated challenges, potential solutions, and perspectives for future developments in the field are discussed.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.571-579
• /
• 2019

Visible light communication (VLC) performs illumination and communication simultaneously, thus it is important to prevent the flicker due to the optical power variation during data transmission and at the same time to have dimming control capability. In this paper, we used Manchester code for flicker-prevention and dimming control. In the transmitter, the duty factor of the Manchester code was used for controlling the LED illumination. In the receiver, the edge-spike signals of an RC-high pass filter were used for recovering the Manchester code while preventing the adjacent noise light. In experiments, the LED light was kept flicker-free and the average optical power was controlled in the range of 8~68 % of the continuous wave (CW) LED light by changing the duty factor of the Manchester code.