• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.6
• /
• pp.83-88
• /
• 2017

In this paper, a 3-port waveguide circulator of Ka-band millimeter-wave for isolation between transmit channel and receive channel at high power transmit mode is designed and fabricated for the seeker of the guided missile and circulator performance is verified through the S-parameter, high power and operation temperature test. At the configuration design, interface design between a seeker antenna and the circulator is considered and half-height of standard waveguide is applied for minimum and light weight body. The shape of permanent magnet and ferrite is optimized by simulation and tuning dielectrics at each port are placed for the best performance. In Fc(center frequency)${\pm}1000MHz$, designed waveguide circulator has below -20 dB return loss, below 0.5 dB insertion loss and below -23 dB isolation. It is found that circulator characteristics is similar to design results.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.3 s.42
• /
• pp.47-54
• /
• 2007

A rotordynamic analysis was performed with a dry vacuum pump, which is a major equipment in modem semiconductor and LCD manufacturing processes. The system is composed of screw rotors, lobes picking air, helical gears, driving motor, and support rolling element bearings of rotors and motor. The driving motor-screw rotor system has a rated speed of 6,300rpm, and was modeled utilizing a rotordynamic FE method for analysis, which was verified through the results of its 3-D finite element model. As loadings on the bearings due to the gear action were significant in the system considered, each resultant bearing load was calculated determinately and indeterminately by considering the generalized forces of the gear action as well as the rotor itself. Each resultant bearing loading was used in calculating each stiffness of rolling element bearings. Design goals are to achieve wide separation margins of critical speeds and favorable unbalance responses of the rotor in the operating range. Then, a complex rotordynamic analysis of the system was carried out to evaluate its forward synchronous critical speeds, whirl natural frequencies and mode shapes, and unbalance responses under various unbalance locations. Results show that the entire system is well designed in the operating range. In addition, the procedure of rotordynamic analysis for dry vacuum pump rotor-bearing system was proposed and established.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.5
• /
• pp.1026-1031
• /
• 2003

Automatic feed pumps are operated and stopped by a pressure switch. Thus, because of repeated operations and stops of the pumps according to fluctuations of water volume, operation with constant rate and pressure is impossible. Moreover, because of repeated running of the pump, keeping up of constant pressure is impossible and damage and energy loss are weak points of the pimps. To make up for defects of an automatic feed pump, this paper designed and made a static pressure feed system which was composed of a feed water control valve, a flow sensor and a control system. The valve device plays an important part in reducing load of pumps by constant water supply regardless of outflow of water. Outflow of water is determined by infrared diode of the flow sensor. The control system is made of a 8 bit micro-processor and the pump was controled by a specific control algorithm. With the constant pressure feed system, discharge pressure was kept at fixed pressure, accurate operations and stops were smoothly accomplished and the pump was operated with constant pressure. Thus, the constant pressure feed system can be considered as an advanced system which made up for the weak points in the current automatic feed systems.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.6
• /
• pp.123-129
• /
• 2013

Android file system is vulnerable to the external access of system resources via its arbitrary access mode and need user's control for SD and UMS medias due to its open architecture. In response to the device control, there is a drawback that its controlability is valid only in the case of embedded linux kernel with VDC function. Hence the solution is to directly implement VDC through system call, with another security module for device storage than system module being added to android system. In this paper the new method of android storage access control for personal information is proposed via VDC for mount system of storage. The access method for SD and UMS were implemented using VDC and mount mechanism. This access control system has been designed to control the granted users in kernel level if files are flowed out by copying. As a result, it was proved through testing that the access control system has exactly detected the write access operation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.4
• /
• pp.675-683
• /
• 2009

RC6 which has different algorithm of encryption and decryption has been proposed to have the same algorithm between encryption and decryption through inserting symmetry layer using simple rotate and logical operation. That means the half of whole RC6 round uses encryption algorithm and the rest of it uses decryption one and symmetry layer has been put into the middle of encryption and decryption. The proposed RC6 algorithm has no difference with the original one in the speed of process. However it is quite safe because by inserting symmetry layer the path of high probability which is needed for differential and linear analysis is cut off so that it is hard to be analyzed. The proposed symmetry layer algorithm can be easily applied to the algorithm which has different encryption and decryption and make it same, and it can be good idea to be used to design a new block cipher algorithm.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.496-503
• /
• 2009

In this paper, a new three-phase interleaved isolated high efficiency boost dc-dc converter with active clamp is proposed. The converter is capable of increased power transfer due to its three-phase power configuration, and it reduces the rms current per phase, thus reducing conduction losses. Further, interleaved operation of three-phase boost converter reduces overall ripple current, which is imposed into fuel cells and realizes smaller sized filter components, increasing effective operating frequency and leading to higher power density. Each output current of three-phase boost converter is combined by the three-phase transformer and flows in the continuous conduction mode by the proposed three-phase PWM strategy. An efficiency of above 96% is mainly achieved by reducing conduction losses and switching losses are reduced by the action of active clamp branches, as well. The proposed converter and three-phase PWM strategy are analyzed, simulated and implemented in hardware. Experimental results are obtained on a 500 W prototype unit, with all of the design verified and analyzed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.504-513
• /
• 2009

This paper proposes the new type LED driver modularization for illumination LED driver. The proposed LED driver circuit insulates a hot GND of AC input power and a cold GND of LED driver part by using a fly-back converter. In order to control easily the current of the LED, the fly-back converter is operated in the discontinuous mode with excellent dynamic characteristics, and the characteristics of the LED are verified after the closed loop control is performed using a KIA2431. The LED driver module allows the wide AC power input ranges and realizes the burst dimming function which directly regulates a PWM control IC. This paper describes the operation principle of the LED driver module and it is proved the usefulness through the real model with experimentation. Besides, this paper proposes the multi-channel LED driver which the miniaturized and modularized LED driver module are connected by parallel, and verified its propriety by experiments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.5C
• /
• pp.454-464
• /
• 2002

In the ATM-PON (Asynchronous Transfer Mode-Passive Optical Network), the downstream cell transmitted by an OLT is broadcast to all ONUs. The ONU receives selectively its own cells by VP filtering. On the other hand, the upstream cell can be transmitted by ONU in the case of receiving a grant from the OLT. After providing the grant to an ONU, the OLT expects the arrival of a cell after an elapse of the equalized round trip delay. ITU-T G.983.1 recommends that one bit error is allowed between the expected arrival time and the actual arrival time at the OLT. Because the ONU processes the different delay to each type of grant (ranging, user cell, and mimi-slot grant), it is not simple to design the transmission part of ONU. In this paper, we implement a grant processor which provides the delay accurately in the ONU TC chip with the FPGA. For the given equalized delay, it deals with the delay for the cell, the byte, and the bit unit by using the shift register, the byte counter, and the D flip-flop, respectively. We verify the operation of the grant processor by the time simulation and the measurement of the optical board output.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.479-485
• /
• 2011

To acquire images in a thermionic-scanning electron-beam system, a scanning unit is needed to control the electron beam emitted from the tungsten filament source. In scanning the electron beam on the solid surface, the signalto-noise ratio depends on the scanning frequency. We used a digital filter to reduce noise by analyzing the real-time frequency of a secondary electron signal. The noise and the true image signal were well separated. We designed the digital filter via a DSP floating-point operation, and the noise elimination resulted in enhanced image quality in a highresolution mode.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.2
• /
• pp.12-21
• /
• 1997

Nowadays, non-pollution energy sources have been strongly needed because of the exhaustion of fossil fuels and serious environmental problems. Because wind energy can be enormously obtained from natural atmosphere, this type of energy has lots of advantages in a economic and pollution point of view. This study has established the aerodynamic and structural design procedure of the rotor blade with an appropriate aerodynamic performance and structural strength for the 500㎾ medium class wind turbine system. The aerodynamic configuration of the rotor blade was determined by considering the wind condition in the typical local operation region, and based on this configuration aerodynamic performance analysis was performed. The rotor blade has the shell-spar structure based on glass/epoxy composite material and is composed of shank including metal joint parts and blade. Structural design was done by the developed design program in this study and structural analysis, for instance stress analysis, mode analysis and fatigue life estimation, was performed by the finite element method. As a result, a medium scale wind turbine rotor blade with starting characteristics of 4m/s wind speed, rated power of 500㎾ at 12m/s wind speed and over 20 years fatigue life has been designed.