• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.2
• /
• pp.169-176
• /
• 2016

In this paper, further research is carried out to investigate the resistance encountered by an icebreaking vessel travelling through level ice and channel ice at low speed range. The present paper focuses on experimental and calculated ice resistances by some empirical formulas in both level ice and channel ice. In order to achieve the research, extra model tests have been done in an ice basin. Based on the measurements from model test, it is found that there exists a relationship between ice resistance, minimum ice load, maximum ice load and the standard deviation of ice load for head on operation in level ice. In addition, both level ice resistance and channel ice resistance are calculated and compared with model test results.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.301-303
• /
• 2002

The load frequency control of power system is one of important subjects in view of system operation and control. To converge within allowance load variation value the frequency and tie-line power flow deviation of each areas, we should regulate the active power output of power plant for regulation in system Applying the NFC(Neuro-Fuzzy Controller) to the model of load frequency control of 2-area power system, we prove that the control is superior to the conventional control technique through computer simulation. For verification of robustness, when we consider generator-rate constraint similar to nonlinearities of power system.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.2
• /
• pp.324-330
• /
• 2013

The dispersion of acoustic noise during the turn-on and turn-off switching of HEV(hybrid electric vehicle) relay was experimentally analyzed to identify the reason for the dispersion of noise level. An effective method was proposed to reduce the dispersion of noise level. First, a method to wrap the side of moving core with a tape was adopted to reduce the transverse vibration. It enabled the moving core to make a consistent motion and reduce the dispersion of noise level from switching operation of relay. Second, the dispersion of noise level from vibration transmission of parts such as the outer frame and yoke caulking part of relay were tested to find out main sources. From this result, it was identified that the yoke caulking part made inconsistent transient vibration and noise dispersion.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.4
• /
• pp.105-110
• /
• 1998

In this study, statistical and neural network methods were used to recognize the cutting tool states. This system employed the tool dynamometer and cutting force signals which are processed from the tool dynamometer sensor using linear discriminent function. To learn the necessary input/output mapping for turning operation diagnosis, the weights and thresholds of the neural network were adjusted according to the error back propagation method during off-line training. The cutting conditions, cutting force ratios and statistical values(standard deviation, coefficient of variation) attained from the cutting force signals were used as the inputs to the neural network. Through the suggested neural network a cutting tool states may be successfully diagnosed.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.8
• /
• pp.119-125
• /
• 1995

Strained multiple quantum well(SMQW) PBH-DFB-LDs emitting at 1.55$\mu$m wavelength has been fabricated using OMVPE and LPE crystal growth tecnique. Using the SMQW active layer, a linewidty enhancement factor of 2.65 was obtained at lasing wavelength and consequnently, packaged 42 modules showed a very low average chirp of 0.44nm at 2.5Gbps NRZ direct modulation. The 77 devices showed average threshold current of 8.72mA and average slope efficiency of 0.181 mW/mA, and single longitudinal mode operation with SMSR larger than 30dB up to 5mW. Among the 77 devices, standard deviation of lasing wavelength of 3.57nm was obtained owing to a good crystal growth uniformity.

• Journal of Environmental Science International
• /
• v.7 no.5
• /
• pp.659-667
• /
• 1998

In the present paper, batch and semi-continuous settling characteristics of a binary calcium carbonate-water system were investigated. Using experimental data of batch settling characteristics, a graphical analysis for a semi-continuous thickening column was developed and compared with experimental results on the basis of Kynch theory, only where the feed velocity line was within the limits of Kynch theorem III. The analysis showed good agreement with experiments. Quite erroneous results, however, was observed for the analysis of a sludge region on the underloaded operation, which was considered due to the deviation from the limits of theory.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.7
• /
• pp.978-983
• /
• 2015

This paper presents Frequency Bias setting for the adequate AGC(Automatic Generator Control) operation based on the frequency response of power system in Korea. AGC frequency control recovers the frequency up to 60Hz following a primary control when the frequency suddenly drops due to a fault in power system. AGC can compensate an appropriate amount of generation by calculating ACE(Are Control Error) from the frequency deviation with the AGC frequency bias set from the actual frequency response in power systems. An appropriateness of the proposed AGC bias setting is verified through case studies employing the simulation model.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.673-678
• /
• 2000

This paper presents an indirect compensation of thermal errors during machining, in which thermal error is modeled as a linear regression of temperatures measured at 4 specified positions. In this regression model, weighting coefficients of the measured temperatures were estimated by using the least square method. The grinding test with compensation, after 4-hour warming-up operation before the test, showed that the maximum machining error of the work pieces was reduced to 12${\mu}{\textrm}{m}$ while it measured 28${\mu}{\textrm}{m}$ without compensation. Furthermore the standard deviation of machining errors was also reduced from 8${\mu}{\textrm}{m}$ to 2${\mu}{\textrm}{m}$.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.193-198
• /
• 2000

The small punch test have been developed to evaluate the material strength of the power plant components. This small punch test specimen is very small than the conventional strength test specimens. Korea Electric Power Research Institute (KEPRI) have been applying this test to assess accurately the life of thermal power plant and enhancing the reliability. The small punch test for gas turbine blades is under development. It's possible to compare the relative strength among the same materials having different operation histories. In this paper, the strength reductions of gas turbine materials are investigated by the small punch tests. All materials shows the almost same strength and deformation with the allowable deviation. At the same test temperature, the damaged material has the maximum load value. The strength reduction is not shown in this small punch test results.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1994.05a
• /
• pp.130-137
• /
• 1994

As a part of developing engineering simulator for CANDU 6 nuclear power plants, present paper gives the tentative simulation results of reactor and turbine power transients including reactor-follow-turbine operation. One point kinetics equations are used for neutron dynamics, iodine and xenon loads. To calculate time-dependent high and low pressure turbine powers and grid frequency deviation, simple first order differential equations are used. In addition, control logics (reactor regulating system, demand power routine, and unit power regulator) used in the plant's process computers have been referenced.