• 패션비즈니스
• /
• 제26권2호
• /
• pp.129-142
• /
• 2022

The purpose of this study is to develop socks to check the range of ankle movement during squats for men in their late 20s. Sensors of 6, 8, and 12 mm were selected, and each sample was impregnated 1 to 3 times. It was prepared using a CNT dispersion, and the GF value was measured using UTM. Among them, the sample with 2 impregnation showed the best GF value. As a result of applying each sample to the socks, the 12 mm sensor was wider than the area of the Achilles tendon, resulting in noise, and the 8 mm sensor was higher than the tensile strength of the socks, resulting in a decrease in the graph. Therefore, testing was performed using a 6 mm sensor. In order to determine the effectiveness of the sensor, the normal operating range was checked through squats, and significant changes were confirmed when the operating range was checked again through squats by performing operations that can increase the operating range through Gastrocnemius, Soleus stretching, and low lunge. Using the results of this study, it is expected that the average value of the ankle movement range of the user is checked prevent injury, to be provided as basic data for the production of shoe products and the promotion of physical health.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권10호
• /
• pp.1027-1032
• /
• 1996

The auto-illumination controller for office, residence, and so on was studied. The system consists of parts of a power supply, a signal oscillator, a lamp controller and two kinds of sensor. The lamp controller has two thyristors triggered by the IR sensor(SCRI) and CdS sensor(SCR2) respectively, When the illuminance around this system is higher than operating value of its sensor, lamp is turned off automatically. Otherwise, the light of lamp gets dim by CdS sensor. In case IR sensor senses the body heat of people around itself, the illuminance of the lamp gets maximum. The illuminance of the lamp can be changed dimmly by control of the variable resistor (RV) connected with SCR2 in series. The turning - on time of the lamp can be also controlled using a variable resistor(Rt) connected with a signal oscillator in parallel. Changing resistance Rt changes the time constant(.tau.), which triggers the gate of SCR2. Though people left the surrounding of lamp, the lamp keeps light for a while.

• 전기학회논문지P
• /
• 제66권2호
• /
• pp.53-57
• /
• 2017

This papers propose a Hall-effect sensors position error compensation method in a sunroof system using a BLDC motor with a low-cost MCU. If the BLDC motor is controlled with this wrong position, the torque ripple and operating current can be increased and the average torque also decreases. Generally, sunroof system has characteristics that operate at constant load for several seconds. It is possible to find the minimum operating current value while changing the position of the Hall-effect sensor during the sunroof operation by using these characteristics. Therefore, propose a method to change the Hall-effect sensor position and find the minimum current value. The validity of the proposed algorithm is verified through experiments.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.78-81
• /
• 2004

A technical performance of the coating depends greatly on the thickness of painting film or coating film. Therefore the confirmed report of the technique to measure accurately is essential to the coating film thickness for the assessment about a coating quality performance. In this paper, two gap sensors - eddy current gap sensor and capacitance gap sensor - which has a different operating principle were used to measure the thickness of a nonmagnetic substance coating film such as paint, enamel or ceramic that was coated on the metallic material. A capacitance gap sensor was used to measure the distance between the sensor head and a coating film and an eddy current gap sensor to measure the distance between the sensor head and a base metal. Then the thickness of a coating film was obtained by the difference of two measurement value. At this result, the suggested dual sensor can measure an arbitrary film thickness to be coated on a base metal as the measurement value of coating thickness exists accurately within the 2％ error.

• 센서학회지
• /
• 제13권2호
• /
• pp.133-138
• /
• 2004

Today, the obstacle detection system has massive size and restrictive detection range. To solve these problems, this paper proposes the capacitance variation detector using the variated capacitance value as a result of the obstacle approaching. If obstacle approaches, the capacitance value of capacitance sensor is increased and the operating frequency of oscillator is decreased. Then this changed frequency appears to the output of the mixer that operate down conversion. The capacitance variation detector is produced by Hynix$0.35{\mu}$ CMOS process. In experiment result, the frequency of final output is 6.81 MHz at no obstacle and 31.45 MHz at approaching obstacle. In conclusion, proposed capacitance variation detector has small size, low power consumption and easiness to set up anywhere. So it is expected to substitute the obstacle detector.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2015년도 추계학술대회
• /
• pp.159-162
• /
• 2015

본 논문에서는 아두이노를 활용한 시각, 청각장애인을 위한 베이비 모니터를 구현하였다. 제안된 베이비 모니터는 측정부, 송신부로 나뉘고 어플리케이션과 연동된다. 측정부는 음량소리센서로 구성되고, 송신부는 블루투스 모듈로 구성된다. 측정부와 송신부는 아두이노 보드에 의해 제어된다. 측정부의 음량소리센서로 소리의 값을 측정하여 제품 내의 아두이노 보드로 값을 전달한다. 측정된 값은 송신부의 블루투스 모듈에 의해 어플리케이션으로 보내진다. 어플리케이션은 받은 값을 판단하고 스마트폰을 제어하여 그 값에 적합한 빛과 소리, 진동을 출력한다. 제안된 베이비 모니터와 어플리케이션이 값에 따라 정확히 동작됨을 보였다.

• Design & Manufacturing
• /
• 제16권4호
• /
• pp.52-59
• /
• 2022

Currently, Korea is an aging society and is expected to become a super-aged society in about four years. X-ray devices are widely used for early diagnosis in hospitals, and many X-ray technologies are being developed. The development of X-ray device technology is important, but it is also important to increase the reliability of the device through accurate data management. Sensor nodes such as temperature, voltage, and current of the diagnosis device may malfunction or transmit inaccurate data due to various causes such as failure or power outage. Therefore, in this study, the temperature, tube voltage, and tube current data related to each sensor and detection circuit of the diagnostic X-ray imaging device were measured and analyzed. Based on QC data, device failure prediction and diagnosis algorithms were designed and performed. The fault diagnosis algorithm can configure a simulator capable of setting user parameter values, displaying sensor output graphs, and displaying signs of sensor abnormalities, and can check the detection results when each sensor is operating normally and when the sensor is abnormal. It is judged that efficient device management and diagnosis is possible because it monitors abnormal data values (temperature, voltage, current) in real time and automatically diagnoses failures by feeding back the abnormal values detected at each stage. Although this algorithm cannot predict all failures related to temperature, voltage, and current of diagnostic X-ray imaging devices, it can detect temperature rise, bouncing values, device physical limits, input/output values, and radiation-related anomalies. exposure. If a value exceeding the maximum variation value of each data occurs, it is judged that it will be possible to check and respond in preparation for device failure. If a device's sensor fails, unexpected accidents may occur, increasing costs and risks, and regular maintenance cannot cope with all errors or failures. Therefore, since real-time maintenance through continuous data monitoring is possible, reliability improvement, maintenance cost reduction, and efficient management of equipment are expected to be possible.

• 전기전자학회논문지
• /
• 제19권2호
• /
• pp.142-147
• /
• 2015

본 논문에서는 자이로 센서와 가속도 센서로부터 얻은 정보를 보정 및 융합하여 자세를 추정하는 칼만 필터 기반 센서 융합 필터의 설계를 제안한다. 최근 센서 네트워크 기술의 발전으로 인해 센터 데이터의 융합 기술이 요구되고 있다. 본 논문에서는 필터의 비선형 시스템 모델을 Jacobian Matrix 연산을 통해 선형 시스템 모델로 변환하며, 오일러 적분을 통해 추정 값을 예측한다. 제안한 필터는 Xilinx 사의 Virtex-6 FPGA Board 를 이용하여 구현하였다. 구현한 필터는 74MHz 동작 주파수로 동작하며, 기존 필터들과 구현한 필터를 비교하여 추정 자세의 정확도 및 신뢰도를 확인하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2008년도 춘계종합학술대회 A
• /
• pp.495-498
• /
• 2008

본 논문은 유비쿼터스 헬스케어 시스템을 위한 웨어러블 센서의 한 종류로서, 손목 착용형 $SpO_2$ 모듈을 구현하였으며 사용자의 산소포화도를 모니터링 할 수 있도록 제안하였다. $SpO_2$ 계측 보드는 고성능, 저전력 특징을 가지고 있는 MCU (ATmega128L, Atmel Co., USA)를 활용하여 모든 측정된 신호의 처리 및 제어를 담당하도록 하였으며, 일차적인 신호의 증폭과 필터를 위한 아날로그 회로도 구성하였다. 또한, 특정부위에서의 측정을 위해 제작된 반사형 프로브와도 연결되어 측정된 신호의 수집 및 처리를 담당하도록 하였다. IEEE 802.15.4 표준 프로토콜과 연동이 가능한 무선 센서 노드는 $SpO_2$ 계측 보드와 함께 연결되어 수집된 데이터를 서버측 PC로 전송하는 역할을 담당한다. 제안된 시스템의 활용으로 관리자가 서버측에서 모니터링 프로그램을 통해 사용자의 건강상태에 대한 정보를 확보할 수 있도록 하였다.

• 센서학회지
• /
• 제18권1호
• /
• pp.72-76
• /
• 2009

The sensing system was designed and fabricated to investigate the ferment environment of soybeans. $NH_3$ gas was saturated after about 7 h and $CO_2$ gas was reached the peak after about 8 h in the inoculation of Bacillus subtilis. However, times that $CO_2$ gas and $NH_3$ gas were reached maximum value without Bacillus subtilis were about 15 h and 18 h, respectively. The sample that inoculated Bacillus subtils had deeper taste than one without it. We found that the peak time of $CO_2$ gas means the starting time of fermentation. If we control the operating time after the start of fermentation, it is expected to make a suitable Chungkukjang to individual preference.