• ETRI Journal
• /
• v.41 no.2
• /
• pp.224-234
• /
• 2019

This paper proposes a new spectrum forecasting (SF) model to estimate the spectrum demands for future mobile broadband (MBB) services. The model requires five main input metrics, that is, the current available spectrum, site number growth, mobile data traffic growth, average network utilization, and spectrum efficiency growth. Using the proposed SF model, the future MBB spectrum demand for Malaysia in 2020 is forecasted based on the input market data of four major mobile telecommunication operators represented by A-D, which account for approximately 95% of the local mobile market share. Statistical data to generate the five input metrics were obtained from prominent agencies, such as the Malaysian Communications and Multimedia Commission, OpenSignal, Analysys Mason, GSMA, and Huawei. Our forecasting results indicate that by 2020, Malaysia would require approximately 307 MHz of additional spectrum to fulfill the enormous increase in mobile broadband data demands.

• East Asian Economic Review
• /
• v.23 no.2
• /
• pp.203-223
• /
• 2019

This paper examines the interactions between financial conditions and business cycles in Mongolia, a small open economy, heavily depending on commodity exports. We construct two financial conditions indexes based on the reduced form IS model and the vector autoregression (VAR) model as surveillance tools to quantify the degree of the financial conditions. We find that real short-term interest rate and real effective exchange rate gap get a higher weight in the FCIs. Both business and financial cycles are often more pronounced in Mongolia, and financial condition is dependent of the financial and monetary policies in place. The analysis of the predictive power of the FCIs for business cycles shows that they have predictive information for the near-term economic activities. FCIs are also helpful in signaling inflation turning points.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.336-340
• /
• 2012

Wide band gap p-type hydrogenated amorphous silicon oxide (a-SiO:H) buffer layer has been used at the interface of transparent conductive oxide (TCO) and hydrogenated amorphous silicon (a-Si:H) p-type layer of a p-i-n type a-Si:H solar cell. Introduction of 5 nm thick buffer layer improves in blue response of the cell along with 0.5% enhancement of photovoltaic conversion efficiency (η). The cells with buffer layer show higher open circuit voltage (Voc), fill factor (FF), short circuit current density (Jsc) and improved blue response with respect to the cell without buffer layer.

• The Korean Journal of Franchise Management
• /
• v.2 no.1
• /
• pp.61-73
• /
• 2011

Supermarket Franchising, as a relatively new mode of retail business, is often regarded as one of the two hallmarks of the "Modern Logistics Revolution". After more than ten years of development, franchise supermarkets have been a rising force in retail business in China. As a product of a highly-developed commercial economy, franchise supermarkets mainly deals in foodstuffs and other daily necessities, featuring low cost, high turnover rate, low prices and diversified inventory. Propelled by the conveniences that come with open shelves and self-service shopping, franchise supermarkets have been growing very rapidly and the rise of many franchise supermarket brands bears testimony to its growth potential and profitability. Meanwhile, in the backdrop of this boom, some franchise supermarkets are going bankrupt. This paper analyzes the current status of franchise supermarkets and some factors bearing on their core competencies, so as to close the competitiveness gap with international retail giants.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.6
• /
• pp.803-809
• /
• 2018

Generally, the gap-and-sag method is used in the shipbuilding stage before coupling the shafts to check whether they are installed at the same position as designed and derived from shaft alignment calculation. The primary installed propeller shaft becomes a reference point, the position of the remaining shafts are sequentially determined through the gap-and-sag value derived from the deflection and deflection angle at each shaft flange by own weight. If the reference point varies against the design value, it would have a series of effects on the installation of the remaining shafts. Moreover, after coupling the shafts, even if the bearing reaction forces derived from measurement are satisfied by the allowable limit range, consequently it might have an adverse effect on the stability of the shafting system by not being able to estimate the relative slope angle between the propeller shaft and the after-stern tube bearing. In this paper, to deal with above-mentioned phenomenon, the theoretical calculations related to designing an effective support point of the aft stern tube bearing and analysis by measurement is conducted through a case of open-up inspections. Based on this, a shaft installation guideline is proposed to minimize the misalignment related to preventing wiping damage of the after-stern tube bearing.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.505-512
• /
• 2014

A new donor-accepter-donor-accepter-donor (D-A-D-A-D) type 2,1,3-benzothiadiazole-thiophene-based acceptor unit 2,5-di(4-(5-bromo-4-octylthiophen-2-yl)-2,1,3-benzothiadiazol-7-yl)thiophene ($DTBTTBr_2$) was synthesized. Copolymerized with fluorene and indeno[1,2-b]fluorene electron-rich moieties, two alternating narrow band gap (NBG) copolymers PF-DTBTT and PIF-DTBTT were prepared. And two copolymers exhibit broad and strong absorption in the range of 300-700 nm with optical band gap of about 1.75 eV. The highest occupied molecular orbital (HOMO) energy levels vary between -5.43 and -5.52 eV and the lowest unoccupied molecular orbital (LUMO) energy levels range from -3.64 to -3.77 eV. Potential applications of the copolymers as electron donor material and $PC_{71}BM$ ([6,6]-phenyl-$C_{71}$ butyric acid methyl ester) as electron acceptors were investigated for photovoltaic solar cells (PSCs). Photovoltaic performances based on the blend of PF-DTBTT/$PC_{71}BM$ (w:w; 1:2) and PIF-DTBTT/$PC_{71}BM$ (w:w; 1:2) with devices configuration as ITO/PEDOT: PSS/blend/Ca/Al, show an incident photon-to-current conversion efficiency (IPCE) of 2.34% and 2.56% with the open circuit voltage ($V_{oc}$) of 0.87 V and 0.90 V, short circuit current density ($J_{sc}$) of $6.02mA/cm^2$ and $6.12mA/cm^2$ under an AM1.5 simulator ($100mA/cm^2$). The photocurrent responses exhibit the onset wavelength extending up to 720 nm. These results indicate that the resulted narrow band gap copolymers are viable electron donor materials for polymer solar cells.

• Journal of the Korean Magnetics Society
• /
• v.23 no.2
• /
• pp.49-53
• /
• 2013

A current sensor is one of important component which is used for the electrical current measurement during charge and discharge of the battery, and monitoring system of the motor controller in the electric and hybrid vehicle. In this study, we have developed an open loop type current sensor using GaAs Hall sensor and magnetic core has an air gap. The Hall sensor detect magnetic field produced by the current to be measured. The 3 mm air gap core was made by HGO electrical steel sheets after slitting, winding, annealing, molding, and cutting. Developed current sensor shows 0.03 % linearity within DC current range from -400 A to +400 A. Operating temperature range was extended to the range of $-40{\sim}105^{\circ}C$ using temperature compensating electronic circuit. To Improve frequency bandwidth limit due to the air flux of PCB (Printed Circuit Board) and Hall sensor, We employed an air flux compensating loop near Hall sensor or on PCB. Frequency bandwidth of the sensor was 100 kHz when we applied sine wave current of $40A{\cdot}turn$ in the frequency range from 100 Hz to 100 kHz. For the dynamic response time measurement, 5 kHz square wave current of $40A{\cdot}turn$ was applied to the sensor. Response time was calculated time reach to 90 % of saturation value and smaller than $2{\mu}s$.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.42-48
• /
• 2012

Due to increase in demand of stable and long pipelines in natural gas industry, wide range of researches are being performed on automation welding to improved welding quality with respect to weld process parameters in real time measurement. In particular, the coupling between the pipe manufacturing process and location of the weld seam, the measured size of the gap that exists in the weld position and the weld angle depending on whether the movement of molten weld. This is due to absence of controlling welding penetration position, depending on the required size of the angle of the setting. In addition, the optimum welding conditions must be considered while selecting, the correlation between these variables and the systematic correlation has not yet been identified. Therefore, in most welded pipe root-pass weld solely depends on the experience of workers in relation to secure a stable weld quality. In this study, automation welding system is implemented to select a suitable root-pass STT (Surface Tension Transfer) welding method using the optimal welding conditions. To successfully accomplish this objective, there were various welding conditions used for welding experiment to confirm that the assessment required for construction through the pipe and automatic welding process is proposed to optimize this plan.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.5
• /
• pp.1356-1364
• /
• 2014

A new conjugated copolymer, poly{4,8-bis(triisopropylsilylethynyl)benzo[1,2-b:4,5-b']dithiophene-alt-4,7- bis(5-thiophen-2-yl)-5,6-difluoro-2-(heptadecan-9-yl)-2H-benzo[d][1,2,3]triazole} (PTIPSBDT-DFDTBTz), is synthesized by Stille coupling polycondensation. The synthesized polymer has a band gap energy of 1.9 eV, and it absorbs light in the range 300-610 nm. The hole mobility of a solution-processed organic thin-film transistor fabricated using PTIPSBDT-DFDTBTz is $3.8{\times}10^{-3}cm^2V^{-1}s^{-1}$. Bulk heterojunction photovoltaic cells are fabricated, with a conventional device structure of ITO/PEDOT:PSS/polymer:$PC_{71}BM$/Ca/Al ($PC_{71}BM$ = [6,6]-phenyl-$C_{71}$-butyric acid methyl ester); the device shows a power conversion efficiency (PCE) of 2.86% with an open-circuit voltage ($V_{oc}$) of 0.85 V, a short-circuit current density ($J_{sc}$) of 7.60 mA $cm^{-2}$, and a fill factor (FF) of 0.44. Inverted photovoltaic cells with the structure ITO/ethoxylated polyethlyenimine/ polymer:$PC_{71}BM/MoO_3$/Ag are also fabricated; the device exhibits a maximum PCE of 2.92%, with a $V_{oc}$ of 0.89 V, a $J_{sc}$ of 6.81 mA $cm^{-2}$, and an FF of 0.48.

• Journal of Korean Society of Forest Science
• /
• v.102 no.3
• /
• pp.355-364
• /
• 2013

This study was conducted to investigate the population structure and dynamics of the Picea jezoensis stands which are located in Mt. Gyebangsan and surveyed from March to October 2012. Results showed that the diameter class distribution of P. jezoensis presented a reverse J-shaped distribution pattern with 32 trees less than 10 cm DBH, 20 trees in 10~30 cm DBH, and 11 trees more than 30 cm DBH. It showed seedlings and saplings of P. jezoensis seem to prefer areas with more sun light or with open upper layer. It was also observed that P. jezoensis preferes areas with organic soils and abundant water such as areas around stumps. Also, occurrences of P. jezoensis stands were analyzed through annual mean radial growth of the trees. And the results showed that the growth naturally or artificially occurred approximately on the years 1854, 1915, 1918, 1993 and 2002 years. Most of the gap-makers were classified as standing dead type with 23 individuals (45.1%).