• Fire Science and Engineering
• /
• v.30 no.6
• /
• pp.1-8
• /
• 2016

In cars, the amount of combustibles, such as plastics, textiles, etc., have increased dramatically to improve the fuel efficiency of cars by reducing the gross vehicle weight according to the increases in an oil price and to reduce environmental problems. One or two cars were involved in a parking lot fire prior to the mid-2000 s. On the other hand, there were many parking lot fires where the entire car was destroyed due to increasing the use of plastics. In this study, the quantity of combustibles in a car was 316.2 kg over a total weight 1935 kg. This is 16.34% of total weight and 10 times greater than that three decades earlier. When a sprinkler is installed as a parking lot fire protection system as a substitute for water spray, the water discharge of the sprinkler must maintain the original density of water spray, $20lpm/m^2$. In addition, the use of a hose reel $CO_2$ system at pilotis parking lots must be prohibited because the hose reel $CO_2$ system has no adaptability for a car fire. Instead, this study proposes foam, dry powder, loaded stream systems be used in parking lot fire suppression systems.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.4
• /
• pp.285-294
• /
• 2014

PURPOSE. The purpose of this study was to evaluate the properties of a porous zirconia scaffold coated with bioactive materials and compare the in vitro cellular behavior of MC3T3-E1 preosteoblastic cells to titanium and zirconia disks and porous zirconia scaffolds. MATERIALS AND METHODS. Titanium and zirconia disks were prepared. A porous zirconia scaffold was fabricated with an open cell polyurethane disk foam template. The porous zirconia scaffolds were coated with ${\beta}$-TCP, HA and a compound of ${\beta}$-TCP and HA (BCP). The characteristics of the specimens were evaluated using scanning electron microscopy (SEM), energy dispersive x-ray spectrometer (EDX), and x-ray diffractometry (XRD). The dissolution tests were analyzed by an inductively coupled plasma spectrometer (ICP). The osteogenic effect of MC3T3-E1 cells was assessed via cell counting and reverse transcriptase-polymerase chain reaction (RT-PCR). RESULTS. The EDX profiles showed the substrate of zirconia, which was surrounded by the Ca-P layer. In the dissolution test, dissolved $Ca^{2+}$ ions were observed in the following decreasing order; ${\beta}$-TCP > BCP > HA (P<.05). In the cellular experiments, the cell proliferation on titanium disks appeared significantly lower in comparison to the other groups after 5 days (P<.05). The zirconia scaffolds had greater values than the zirconia disks (P<.05). The mRNA level of osteocalcin was highest on the non-coated zirconia scaffolds after 7 days. CONCLUSION. Zirconia had greater osteoblast cell activity than titanium. The interconnecting pores of the zirconia scaffolds showed enhanced proliferation and cell differentiation. The activity of osteoblast was more affected by microstructure than by coating materials.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.5
• /
• pp.484-491
• /
• 2017

Recent research has shown that quadrupole noise has a significant influence on the overall characteristics of flow-induced noise and on the performance of underwater appendages such as sonar domes. However, advanced research generally uses the Ffowcs Williams-Hawkings analogy without considering the quadrupole source to reduce computational cost. In this study, flow-induced noise is predicted by using an LES turbulence model and a developed formulation, called the formulation Q1As method to properly take into account the quadrupole source. The noise around a circular cylinder in an underwater environment is examined for two cases with different velocities. The results from the method are compared to those obtained from the experiments and the permeable FW-H method. The results are in good agreement with the experimental data, with a difference of less than 1 dB, which indicates that the formulation Q1As method is suitable for use in predicting quadrupole noise around underwater appendages.

• Nuclear Engineering and Technology
• /
• v.47 no.1
• /
• pp.33-46
• /
• 2015

During the past 10 years, the Korea Atomic Energy Research Institute (KAERI) has performed a study to control hydrogen gas in the containment of the nuclear power plants. Before the Fukushima accident, analytical activities for gas distribution analysis in experiments and plants were primarily conducted using a multidimensional code: the GASFLOW. After the Fukushima accident, the COM3D code, which can simulate a multidimensional hydrogen explosion, was introduced in 2013 to complete the multidimensional hydrogen analysis system. The code validation efforts of the multidimensional codes of the GASFLOW and the COM3D have continued to increase confidence in the use of codes using several international experimental data. The OpenFOAM has been preliminarily evaluated for APR1400 containment, based on experience from coded validation and the analysis of hydrogen distribution and explosion using the multidimensional codes, the GASFLOW and the COM3D. Hydrogen safety in nuclear power has become a much more important issue after the Fukushima event in which hydrogen explosions occurred. The KAERI is preparing a large-scale test that can be used to validate the performance of domestic passive autocatalytic recombiners (PARs) and can provide data for the validation of the severe accident code being developed in Korea.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.281-281
• /
• 2019

수리모형실험은 수로 내에서 장시간 파랑을 발생시킬 경우, 수로 내에 반사 파랑의 성분이 누적될 수 있어 상당한 계측 오차를 발생시킬 우려가 있어 수리모형실험 결과의 검증이 필요하다. 일반적으로 수리모형실험 결과의 검증을 위해서는 동일 실험을 무수히 반복하여 불확실성을 제거하거나 다양한 수리실험실에서 수리모형실험을 수행하고 결과를 분석하여 불확실성을 제거할 수 있다. 그러나 이는 엄청난 시간과 노력은 물론 막대한 실험비용이 소요되기 때문에 경제적으로 효용성이 매우 낮아 현실적으로 수행이 어렵다. 이에 비해 수치모형실험은 상대적으로 저렴한 비용으로 수행할 수 있으며, 다수의 실험을 수행하지 않아도 불확실성을 제거할 수 있어 수리모형실험의 검증에 효율적이다. 일반적으로 난류 거동을 동반하는 복잡한 구조물 주변의 흐름 해석에는 3차원 CFD 모형이 필요하다. 특히, 병렬연산이 가능한 CFD 모형을 활용하면 수리모형실험에서도 재현이 쉽지 않은 다양한 조건에 따른 복잡한 흐름을 해석할 수 있어 효용성이 점점 증가하고 있다. 그러나 복잡한 구조물이 존재하게 되면 구조물에 재현에 막대한 격자구조가 필요하여 현실적으로 적용이 쉽지 않다. 이에 대한 대안으로 복잡한 구조물을 비교적 큰 격자에서 재현할 수 있는 가상경계법을 활용하는 연구가 활발히 진행되고 있다. 가상경계법은 Navier-Stokes 방정식에서 유체 내에 존재하는 고체를 모멘텀 이론으로 대체하여 고려하는 기법으로 수치모델링 수행 시 매질을 유체만으로 구성할 수 있어 안정적으로 적용할 수 있는 것으로 알려져 있다. 본 과업에서는 다양한 분야에서 널리 활용되고 있는 3차원 CFD 모형인 OpenFOAM®기반으로 파랑해석에 필요한 경계조건을 계산할 수 있는 olaFlow를 활용하여 복잡한 구조물을 지나는 파랑해석을 수행하기 위해 가상경계법을 olaFlow에 도입한 수치 알고리즘을 개발하였다. 개발한 수치알고리즘을 활용하여 복잡한 구조를 수치모델에서 재현하였으며, 수치모델에 적용된 수치 알고리즘의 안정성에 대해 고찰하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.1
• /
• pp.23-33
• /
• 2019

Unmanned Surface Vehicle (USV) is being developed to do maritime survey and maritime surveillance at Korea Research Institute of Ships & Ocean engineering (KRISO). The goal is that USV should be operated at the maximum speed of 45 knots and it should be operated at sea state 4. Therefore the planing hull of USV should be excellent in resistance performance and manoeuvring performance. It is needed to check its performance using Experimental Fluid Dynamics (EFD), Computational Fluid Dynamics (CFD) or analytic method before designing the hull. In this study, resistance performance was analyzed by EFD and CFD. EFD with heave and pitch was performed at high speed towing system in Seoul National University. CFD was performed using SNUFOAM based on openFOAM with dynamic mesh to calculate running attitudes. The results of CFD were compared with EFD results. The results of CFD were resistance, running attitudes and wave height. The flow distribution and pressure distribution were also analyzed. The results of numerical resistance was under estimated than EFD. Even though the results of CFD have a slight limitation, it can be successfully used to estimate the resistance performance of planing hull. In addition it can be used as a supplement for EFD results.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.4
• /
• pp.199-208
• /
• 2019

Regular waves were generated in a wave flume under perfect reflection condition to evaluate performance of three CFD models of CADMAS-SURF, olaFlow, and KIOSTFOAM. The experiments and numerical simulations were carried out for three different conditions of non-breaking, breaking of standing waves, and breaking of incident waves. Among the three CFD models, KIOSTFOAM showed best performance in reproducing the experimental results. Although the run time was reduced by using CADMAS-SURF, its computational accuracy was worse than KIOSTFOAM. olaFlow was the fastest model, but active wave absorption at the wave generation boundary was not satisfactory. In addition, the model excessively dissipated wave energy when wave breaking occurred.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.892-901
• /
• 2020

We used a numerical method to estimate the hydrodynamic maneuvering derivatives for the heave-pitch coupling motion of an underwater glider. It is very important to assess the hydrodynamic maneuvering characteristics of a specific hull form of an underwater glider in the initial design stages. Although model tests are the best way to obtain the derivatives, numerical methods such as the Reynolds-averaged Navier-Stokes (RANS) method are used to save time and cost. The RANS method is widely used to estimate the maneuvering performance of surface-piercing marine vehicles, such as tankers and container ships. However, it is rarely applied to evaluate the maneuvering performance of underwater vehicles such as gliders. This paper presents numerical studies for typical experiments such as static drift and Planar Motion Mechanism (PMM) to estimate the hydrodynamic maneuvering derivatives for a Ray-type Underwater Glider (RUG). A validation study was first performed on a manta-type Unmanned Undersea Vehicle (UUV), and the Computational Fluid Dynamics (CFD) results were compared with a model test that was conducted at the Circular Water Channel (CWC) in Korea Maritime and Ocean University. Two different RANS solvers were used (Star-CCM+ and OpenFOAM), and the results were compared. The RUG's derivatives with both static drift and dynamic PMM (pure heave and pure pitch) are presented.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.236-245
• /
• 2021

In this study, direct numerical and large eddy simulations of transitional flows around studs were conducted to investigate the effectiveness of turbulence stimulators at very low speeds for the minimum propulsion power condition of four knots. For simplicity, the studs were assumed to be installed on a flat plate, while the wake was observed up to 0.23 m downstream behind the second stud. For applicability to a model ship, we also studied the flow characteristics behind the first and second studs installed on a curved plate, which was designed to describe the geometry of a bulbous bow. A laminar-to-turbulent transition was observed in the wake at Re_D ≥ 921 (U_∞≥0.290 m/s), and the wall shear stress at Re_D = 1162 (U_∞ = 0.366 m/s) in the second wake was similar to that of the fully developed turbulent boundary layer after a laminar-to-turbulent transition in the first wake. At Re_D = 581 (U_∞ = 0.183 m/s), no turbulence was stimulated in the wake behind the first and second studs on the flat plate, while a cluster of vortical structures was observed in the first wake over the curved plate. However, a cluster of vortical structures was revealed to be generated by the reattachment process of the separated shear layer, which was disturbed by the first stud rather than directly initiated by the first stud. It was quite different from a typical process of transition, which was observed at relatively high Re_D that the spanwise scope of the turbulent vortical structures expanded gradually as it went downstream.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.3
• /
• pp.141-148
• /
• 2022

A hybrid turbulence model has developed by combining a sub-grid scale model using dynamic k equation in LES with k-𝜔 SST model of RANS equation. To ascertain potential applicability of the hybrid turbulence model, fully developed turbulent channel flows at Re_𝜏=180 have been simulated of which computational domain has a top wall with coarse cells and a bottom wall with fine cells. The streamwise mean velocity and turbulent intensity profiles showed a good agreement with DNS data when using the hybrid model rather than using a single model in k-𝜔 SST or dynamic k equation models. Computational simulations of turbulent flows around KVLCC2 with a pre-swirl duct have been mainly performed using the hybrid turbulence model. Compared to the results obtained from RANS simulation with k-𝜔 SST model as well as LES with dynamic k equation SGS model, turbulent wakes of the duct in the present simulation using the hybrid turbulence model were very similar to that of LES. Also, the resistances acting on hull, rudder and duct in hybrid turbulence model were similar to those in RANS simulation whereas the viscous forces acting on the hull in LES had a significant error due to coarse cells inappropriate to the sub-grid scale model.