• Advances in concrete construction
• /
• 제12권5호
• /
• pp.399-409
• /
• 2021

The existing method to improve the coordination performance of the inner and outer parts of concrete-encased concrete-filled steel tube (CFST) composite columns by increasing the volume-stirrup ratio causes difficulties in construction due to over-dense stirrups. Thus, this paper proposes an open polygonal composite stirrup with high strength and high ductility CRB600H reinforced rebar, and seventeen specimens were constructed, and their axial compressive performance was tested. The main parameters considered were the volume-stirrup ratio, the steel tube size, the stirrup type and the stirrup strength. The test results indicated: For the specimens restrained by open octagonal composite stirrups, compared with the specimen of 0.5% volume-stirrup ratio, the compressive bearing capacity increased by 14.6%, 15.7% and 21.5% for volume-stirrup ratio of 0.73%, 1.07% and 1.61%, respectively. For the specimens restrained by open composite rectangle stirrups, compared with the specimen of 0.79% volume-stirrup ratio, the compressive bearing capacity increased by 7.5%, 6.1%, and -1.4% for volume-stirrup ratio of 1.12%, 1.58% and 2.24%, respectively. The restraint ability and the bearing capacity of the octagonal composite stirrup are better than other stirrup types. The specimens equipped with open polygonal composite stirrup not only had a higher ductility than those with the traditional closed-loop stirrup, but they also had a higher axial bearing capacity than those with an HPB300 strength grades stirrup. Therefore, the open composite stirrup can be used in practical engineering. A new calculation method was proposed based on the stress-strain models for confined concrete under different restrain conditions, and the predicted value was close to the experimental value.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권6호
• /
• pp.302-310
• /
• 2002

This paper presents an application of a improved branch exchange (IBE) algorithm with a tie branch power (TBP) flow equation to solve the Optimal Routing problem for operation of a radial Power system including power distribution system. The main objective of the Optimal Routing problem usually is to minimize the network real power loss and to improve the voltage profile in the network. The new BE algorithm adopts newly designed methods which are composed by decision method of maximum loss reduction and new index of loss exchange in loop network Thus, the proposed algorithm in this paper can search the optimal topological structures of distribution feeders by changing the open/closed states of the sectionalizing and tie switches. The proposed algorithm has been evaluated with the practical IEEE 32, 69 bus test systems and KEPCO 148 bus test system to show favorable performance gained.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.655-660
• /
• 2001

The performance test of a centrifugal compressor for APU(Auxiliary Power Unit) which is developed by the collaborative research of KARI and Samsung TechWin has been conducted. The investigated compressor consists of a curved inlet, a centrifugal impeller, a channel diffuser and a plenum chamber. The experiments were carried out in an open-loop centrifugal compressor test rig driven by a turbine. For three different diffusers, overall performance data were obtained at 80%, 90% and 97% of design speed. For the initially designed wedge-type diffuser, test results showed that the compressor was operated at a higher mass flow rate than the design requirement. By reducing the diffuser throat area, the compressor operating range was shifted to lower mass flow rate range. The test result of redesigned wedge-type diffuser showed high pressure loss. To reduce the diffuser loss, diffuser inlet radius was increased and airfoil-type of diffuser was adopted. This airfoil-type diffuser showed reasonal results in terms of design requirement.

• Nuclear Engineering and Technology
• /
• 제45권7호
• /
• pp.871-894
• /
• 2013

KAERI (Korea Atomic Energy Research Institute) has been operating an integral effect test facility, the Advanced Thermal-Hydraulic Test Loop for Accident Simulation (ATLAS), for transient and accident simulations of advanced pressurized water reactors (PWRs). Using ATLAS, a high-quality integral effect test database has been established for major design basis accidents of the APR1400 plant. A Domestic Standard Problem (DSP) exercise using the ATLAS database was promoted to transfer the database to domestic nuclear industries and contribute to improving a safety analysis methodology for PWRs. This $2^{nd}$ ATLAS DSP (DSP-02) exercise aims at an effective utilization of an integral effect database obtained from ATLAS, the establishment of a cooperation framework among the domestic nuclear industry, a better understanding of the thermal hydraulic phenomena, and an investigation into the possible limitation of the existing best-estimate safety analysis codes. A small break loss of coolant accident with a 6-inch break at the cold leg was determined as a target scenario by considering its technical importance and by incorporating interests from participants. This DSP exercise was performed in an open calculation environment where the integral effect test data was open to participants prior to the code calculations. This paper includes major information of the DSP-02 exercise as well as comparison results between the calculations and the experimental data.

• 한국산학기술학회논문지
• /
• 제17권6호
• /
• pp.1-8
• /
• 2016

오늘날 전류센서는 전류량 제어, 감시, 계측 등 매우 다양한 분야에서 사용되고 있다. 또한 전력망의 스마트 그리드사업, 신재생에너지 발전, 전기자동차와 하이브리드 자동차 등의 수요가 커지면서 그 사용영역이 점차 확대되고 있는 추세이다. 여러 종류의 전류센서 중에서 홀 소자를 사용하는 개방형 전류센서는 다른 형식의 전류센서에 비해 가격이 싸고, 크기와 무게가 작은 장점이 있지만 정밀도가 낮고 주위의 온도 변화에 따라 특성이 변하는 것이 단점이다. 이러한 단점을 보완하기 위하여 본 연구에서는 정밀도와 온도성능이 뛰어난 300A급 개방형 전류센서를 설계 및 제작하였다. 300A급 개방형 전류센서를 제작하기 위해서 수치해석을 통해 철심을 설계하고 회로해석 프로그램을 이용하여 신호처리에 필요한 회로들을 설계하였다. 이러한 과정을 통해서 SMD(Surface Mount Device) 형태로 제작된 300A급 개방형 전류센서는 30 ~ 300A의 직류 및 교류전류를 통전한 실험에서 정밀도 오차가 0.75% 이내, 선형도 오차가 0.19% 이내였다. 또한 온도보상회로를 포함한 전류센서를 $-25{\sim}85^{\circ}C$의 온도범위에서 동작시켰을 때 온도계수는 $0.012%/^{\circ}C$ 이내였다.

• 대한기계학회논문집A
• /
• 제21권7호
• /
• pp.1013-1020
• /
• 1997

Among various gyroscopes, the vibrating gyroscope has advantages such as compact size, mass-productivity and low cost. However this kind of gyroscope usually suffer from low linearity and low signal to noise ratio. Therefore, it is necessary to study on vibrating gyroscope to improve performance. In this paper, triangular cross section si selected in consideration for several points. The existing designs of exciting and sensing have some problems such that small signal size and low linearity. This paper proposes new design of exciting and sensing which is named one period exciting and the other period sensing. This design improves signal size, but it cannot improve linearity. This is because above two designs are the same open-loop type. So, another new design is proposed, which is named rebalancing, is applied to one period exciting and the other period sensing. This design are closed-loop type. It feedbacks the output signal. According to control theory, it can improve linearity. The circuits of each design are realized and used to calibration test. Calibration results show that new design of rebalancing improves linearity and signal size.

• 드라이브 ㆍ 컨트롤
• /
• 제17권2호
• /
• pp.45-54
• /
• 2020

The IMV is a combination of four two-way valve systems which replace a conventional four-way spool valve to improve efficiency mostly in excavator hydraulics. As the environmental regulations for construction equipment have tightened, some overseas advanced companies have released commercial excavators in which the MCV is implemented with the IMVs. Development of the IMV type MCV relies on the control algorithm as well as the robust performance of proportional flow control valves. In this study, the IMV controller was designed and verified with experiments for the excavator working unit, which determines the IMV mode of operation and the extent of the valve opening in consideration of the load conditions on hydraulic actuators. First, the open-loop controller was designed with a joystick command vs. a PSV reference current map comprising several control parameters in to compensate for the different flow characteristics and non-linearities of two-way flow control valves. Second, the closed-loop controller was designed with the PI control fed by the actuator displacement and outputs actuator percent effort equivalent to the operator's joystick command. Finally, the performance of the IMV type MCV was verified with the trajectory control of position references derived from the energy consumption test standard. Experimental results showed the control performance of the IMV developed in this study, and suggest that future studies to be conducted to advance technical progress.

• 항공우주시스템공학회지
• /
• 제10권1호
• /
• pp.86-94
• /
• 2016

In this paper, position control of focal plane compensation device using piezoelectric actuator is conducted. The forcal plane compensation device installed on earth observation satellite camera compensates micro-vibration from reaction wheels. In this study, four experimental models of the open-loop compensation device are derived using MATLAB system identification toolbox in the input range of 0~50Hz. Subsequently, the PID controller for each model is designed and the performance test of each controller is conducted through MATLAB/Simulink. According to frequency response analysis of the closed-loop compensation device system, the PID controller designed for 38~50Hz input range has enough tracking performance for the whole 0~50Hz input range. The maximum output error is about $1{\mu}m$ for the input range. The simulation results has been verified by the experimental method.

• Korean Chemical Engineering Research
• /
• 제43권3호
• /
• pp.360-365
• /
• 2005

SMB는 연속 크로마토그래피 공정으로써 회분식 크로마토그래피보다 이동상의 소비를 줄이고 높은 농도, 높은 수율의 생산성의 장점을 가지고 있다. 그러나 운전상의 복잡성 때문에 이 공정을 이해하기 어렵다. 본 실험에서는 서로 다른 색깔을 지닌 두 물질의 분리를 시도함으로써 공정의 이해를 용이하게 하였다. 실험에서 사용된 물질은 Blue dextran과 Orange G로서 각각 파란색과 오렌지 색을 띤다. 실험은 4개의 존으로 구성된 SMB로써 zone VI에서 zone I으로 재순환 되지 않는 열린 루프계가 적용되었다. 운전 조건은 Standing wave design를 이용하였으며 extract와 raffinate에서 높은 순도와 수율을 가질 수 있도록 디자인하였다. 단일 칼럼을 이용한 실험을 통해서 여러 유량에서 비선형 흡착 평형식과 실험식으로부터 물질전달계수를 얻었다. Extract와 raffinate의 농도분포 곡선은 모사 결과와 거의 일치하였다. Extract와 raffinate의 순도는 99.49％와 98.89％이며 두 물질의 수율은 모두 98％였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.183-187
• /
• 2012

In the present study, a feasibility study on an innovative satellite attitude control actuator is performed. The actuator is specially designed to generate the reaction torque in an arbitrary axis, so that a satellite attitude can be controlled by using itself. It consists of a spherical flywheel and electromagnets for levitation and rotation control of the ball. As the earlier study, a rotating performance test on the spherical actuator is conducted in a single rotating axis and vertical levitation condition. From the test results, it can be confirmed that the maximum speed and torque of the innovative device are 7,200rpm and 0.7Nm, respectively. Using torque-voltage characteristics of the spherical motor, an open-loop control (V/f constant control) is performed, and the test results show excellent control performance in acceleration and deceleration phases.