• 한국자기학회지
• /
• 제12권5호
• /
• pp.174-178
• /
• 2002

미소결함을 가진 금속체에 교류자기장을 인가하면 결함부근에는 와전류의 분포가 달라져 이에 의해 금속체를 관통하는 교류자기장은 결함부근에서 차이를 가진다. 이 교류자기장을 비정질 와이어로 된 센서헤드로 측정하여 센서헤드의 유기전압 크기로부터 결함 유무를 검출하는 방법에 대해 검토하였다. 비정질 와이어는 Co-based재료로 자왜가 거의 0이며 고투자율 자성체이고 비정질 와이어는 길이가 15mm, 직경이 100$\mu\textrm{m}$인 원주형 자성체이다. 실험대상 금속체로 0.5mm의 단일 직선 갭을 가진 두께 1mm의 동판과 0.1mm의 갭이 규칙적으로 배열된 두께 25$\mu\textrm{m}$의 Al 판를 이용하였다. 스파이럴 코일에 인가하는 교류자기장의 주파수는 100KHz~600KHz였다. 본 실험의 결과에서 동판에서는 유기전압의 최대치와 최소치의 차가 약 2.5㎷ 얻어졌고, Al판에서는 500KHz에서 0.4㎷가 얻어져 직선 갭의 유무를 유기전압의 크기만으로 확인할 수 있었다.

• 대한치과교정학회지
• /
• 제43권4호
• /
• pp.186-192
• /
• 2013

Objective: To analyze the fatigue resistance, debonding force, and failure type of fiber-reinforced composite, polyethylene ribbon-reinforced, and braided stainless steel wire lingual retainers in vitro. Methods: Roots of human mandibular central incisors were covered with silicone, mimicking the periodontal ligament, and embedded in polymethylmethacrylate. The specimens (N = 50), with two teeth each, were randomly divided into five groups (n = 10/group) according to the retainer materials: (1) Interlig (E-glass), (2) everStick Ortho (E-glass), (3) DentaPreg Splint (S2-glass), (4) Ribbond (polyethylene), and (5) Quad Cat wire (stainless steel). After the recommended adhesive procedures, the retainers were bonded to the teeth by using flowable composite resin (Tetric Flow). The teeth were subjected to 10,00,000 cyclic loads (8 Hz, 3 - 100 N, $45^{\circ}$ angle, under $37{\pm}3^{\circ}C$ water) at their incisoproximal contact, and debonding forces were measured with a universal testing machine (1 mm/min crosshead speed). Failure sites were examined under a stereomicroscope (${\times}40$ magnification). Data were analyzed by one-way analysis of variance. Results: All the specimens survived the cyclic loading. Their mean debonding forces were not significantly different (p > 0.05). The DentaPreg Splint group (80%) showed the highest incidence of complete adhesive debonding, followed by the Interlig group (60%). The everStick Ortho group (80%) presented predominantly partial adhesive debonding. The Quad Cat wire group (50%) presented overlying composite detachment. Conclusions: Cyclic loading did not cause debonding. The retainers presented similar debonding forces but different failure types. Braided stainless steel wire retainers presented the most repairable failure type.

• 한국의류산업학회지
• /
• 제20권1호
• /
• pp.101-107
• /
• 2018

The purpose of this study is to develop the electroconductive textiles based on polyurethane(PU) nanoweb and to explore that it is applicable to smart clothing. The electroconductive textiles developed by coating 2.0 wt% aqueous dispersed non-oxidized graphene paste on the surface of PU nanoweb. The fabricated electroconductive nanoweb was applied as a transmission line to connect the LED lamp, and the brightness of the LED lamp was measured to confirm its performance. The nanoweb transmission line was fixed by two methods(seam sealing tape, embroidering) to connect the LED lamp and AA batteries. The results as follows, the brightness of the LED lamp fixed with seam sealing tape was about 82 lux, and which fixed with embroidering was about 57 lux. It represents that the nanoweb transmission line which fixed with the seam sealing tape has better electrical signal transmitting because the lux value higher than the one fixed by embroidering. In order to compare the performance of the nanoweb transmission line and the metal wire, we connected the LED lamp with copper wire. The brightness of copper wire connected LED lamp was about 193 lux. Although the electrical signal strength of the nanoweb transmission line was weaker than the copper wire, it was reachable to operate LED lamp. The results of this study will provide a basic data to develop the textile based electronic devices, and conducting wire for smart clothing.

• 대한관절경학회지
• /
• 제2권1호
• /
• pp.45-50
• /
• 1998

Recently, a variety of arthroscopic techniques have been reported for the treatment of the displaced tibial eminence fracture. The purpose of this study was to describe details of arthroscopic technique using pull-out wire and to evaluate the results. Eleven patients with irreducible type II and type III tibial eminence fractures underwent the arthroscopic reduction and internal fixation using double strand pull-out wiring. The anterior cruciate ligament tibial drill guide was utilized for the reduction of fracture and passage of the guide pins. The tibial eminence fracture was firmly fixed with double strand 26-gauge pull-out wire(0.45mm diameter). Fracture union was achieved at 7.2 weeks (range, six to eight weeks) after operation. All cases were united at the last follow-up. Subjectively, nine patients had no pain and no restriction of daily activities. Two patients with combined injuries had limitation of knee motion(10 to 130 degrees, respectively) and one patient showed mild anterior laxity. Early rehabilitation was enabled without loss of reduction and breakage of pull-out wire. The arthroscopic reduction and internal fixation using pull-out wire showed good results including early rehabilitation, early fracture union, minimal morbidity, and no requirement of the second operation for hard ware removal.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.187-192
• /
• 2002

Applicability of laser micro welding process to the fabrication of medical devices was investigated. Austenitic stainless steel wire (SUS304) was spot melted and crosswise welded, which is one of the most possible welding process for the fabrication of medical devices, by using a Nd-YAG laser. Effects of welding parameters on the microstructure, tensile strength and corrosion resistance were discussed. In the spot melting, melted metal width decreased with decreasing the input energy and pulse duration. Controlling the laser wave to reduce laser noise which occurred in the early stage of laser irradiation made reasonable welding condition wider in the welding condition of small pulse duration such as 2ms. The microstructure of the melted metal was a cellular dendrite structure and the cell size of the weld metal was about 0.5~3.5 ${\mu}{\textrm}{m}$. Tensile strength increased with the decrease of the melted metal width and reached to a maximum about 660MPa, which is comparable with that for the tempered base metal. Even by immersion test at 318K for 3600ks in quasi biological environment (0.9% NaCl), microstructure of the melted metal and tensile strength hardly changed from those for as melted material. In the crosswise welding, joints morphologies were classified into 3 types by the melting state of lower wire. Fracture load increased with input energy and melted area of lower wire, and reached to a maximum about 80N. However, when input energy was further increased and lower wire was fully melted, fracture load decreased due to the burn out of weld metal.

• 한국환경복원기술학회지
• /
• 제16권1호
• /
• pp.17-25
• /
• 2013

The mechanical properties appeared at the concrete mixed with Polypropylene fiber($1kg/m^3$, $3kg/m^3$, $5kg/m^3$) are compared with normal concrete and wire mesh one and evaluated. Achieved slump test to search effect that PP fiber gets to workability, even if the mixing amount of fiber increases, confirmed that slump value is no change almost. The no difference can be caused by hard mixture, but because of the big softness of fiber there is no effect greatly up to PP fiber mixing amount $5kg/m^3$ even with soft mixture. Compressive strengths and flexural strengths of the concretes with PP fiber and without the fiber are appeared almost alike. If examine load resistance ability by PP fiber mixing amount increase, it could know that the increase of fiber mixing amount improves load resistance ability and the toughness index is increased. While normal concrete is broken at the same time with crack, fiber mixed concrete stand in flexure load continuously after crack occurrence. In compare with wire mesh embeded concrete, wire mesh mixed concrete stands in some degree in flexure load by wire mesh crack occurrence and the test piece was broken at the same time. But, it could know that the PP fiber mixed concrete resist continuously to flexure load in bigger displacement.

• Clinics in Shoulder and Elbow
• /
• 제19권3호
• /
• pp.149-154
• /
• 2016

Background: The purpose of this study is to compare clinical and radiological outcomes between trans-acromial fixation with Kirschner's wire (K-wire) and AO locking hook plate fixation for acute acromioclavicular (AC) joint dislocation. Methods: This study included 61 patients who underwent either closed reduction and trans-acromial fixation with K-wire (group A, 23 patients) or open reduction and internal fixation with AO locking hook plate (group B, 38 patients). Pain on a visual analogue scale (VAS) score, the University of California Los Angeles (UCLA) shoulder score, the American Shoulder and Elbow Surgeons (ASES) score, and active range of motion (ROM) were used in the functional evaluation. For radiological evaluation, coracoclavicular distance (CCD) was measured on both clavicular anteroposterior view and compared between groups. Results: At one-year follow-up, no significant differences in VAS pain score, UCLA shoulder score, ASES score, and active ROM were observed between groups, despite five cases (22.7%, 5/23) of complication in group A. The side-to-side difference between normal and affected CCD was $2.4{\pm}2.2mm$ in group A and $0.2{\pm}0.7mm$ in group B. This difference showed a statistical significance between groups (p<0.001). Conclusions: For the treatment of acute AC joint dislocation, the K-wire trans-acromial fixation group showed a significantly greater CCD than the AO locking hook plate group. In addition, during the follow-up period, much higher incidence of complication related to implant was observed in the trans-acromial fixation group. Although clinical outcomes between groups were not significantly different, these results should be interpreted carefully.

• 대한의용생체공학회:의공학회지
• /
• 제16권4호
• /
• pp.481-491
• /
• 1995

Endovaginal and endorectal receiver only surface coils were designed for MR imaging (MRI) and $^1H$ MR spectroscopy (MRS) for the uterine cervix and the prostate. The shape of endovaginal coil wire was rectangular with round corner. Size of the coil wire was empirically determined for 7cm and 4cm along the long and short axis, respectively. The coil wire loop was supported by acryl handle and bent about $150^{\circ}$ at one side of the loop considering the average angle of the cervix to the vagina. We called this as a "spoon-type endovaginal coil". The wire of the endorectal coil was made of the flexible materials so that the wire loop became long elliptic shape by pushing the acryl handle into the plastic tube for the comfort of patients when the coil was inserted into the cervix. Then, the shape was maintained to be circle by popping out handle. Conventional spin echo (SE) and fast spin echo (FSE) sequences were used as 71 and 72 weighted imaging sequences, respectively. Matrix size was 128~$256{\times}256$. FOVs for surface coil and body coil were 14cm and 24cm, respectively. 3D volume localized in vivo $^1H$ MR spectroscopy of the human cervix and prostate was performed using PRESS or STEAM localization method with the following parameters . TR=3 sec, TE=135 msec for PRESS or 30 msec for STEAM, NEX=2, NS=48, Sl=2048, and SW=2500 Hz. Using home-built endovaginal and endorectal coils, excellent T1- and T2-images were obtained to visualize early cervical and prostate tumors. 3D volume localized in vivo IH MRS was useful to differentiate the cancerous tissue from the normal tissue.

• 한국지반환경공학회 논문집
• /
• 제6권3호
• /
• pp.35-45
• /
• 2005

낙석방지울타리는 국내에서 가장 보편적으로 사용되는 낙석방지공법의 하나로 일반적으로 H형강, 와이어메쉬 및 와이어로프의 세 부분으로 구성되며 이들에 의해 발휘되는 낙석방지울타리의 총 흡수가능에너지가 낙석에너지보다 커야한다는 것을 기본적인 설계개념으로 한다. 본 연구에서는 기존 낙석방지울타리의 와이어메쉬와 와이어로프 대신, 새로운 재료인 팽창메탈을 사용한 낙석방지울타리의 성능을 평가하고 기존의 낙석방지울타리와 비교하였다. 이를 위하여 팽창메탈 낙석방지울타리와 기존 방식의 낙석방지울타리에 대하여 실내 및 현장시험을 실시하였으며, 그 결과 팽창메탈 낙석방지울타리의 흡수가능에너지는 기존 낙석방지울타리와 비교해 높은 것으로 나타나 팽창메탈은 성능 및 경제적인 면에서 기존 재료에 비해 우수한 재료임을 보였다.

• 한국지반환경공학회 논문집
• /
• 제10권6호
• /
• pp.49-60
• /
• 2009

본 연구는 기존의 낙석방지울타리에 적용되는 와이어로프를 경강선으로 대체하고 소재 및 체결부에 대한 실내성능실험과 더불어 현장에서의 수직낙하시험을 통해 전체적인 에너지 흡수능력을 평가하여 새로운 낙석방지울타리를 개발하는데 있다. 12단 경강선 적용 낙석방지울타리의 수직낙하시험 결과, 국내 낙석방지울타리에 기준으로 적용되는 흡수에너지인 50kJ 이상의 에너지를 흡수하는 것으로 나타났다. 또한 경강선 단수가 12단에서 16단으로 증가함에 따라 에너지 흡수능력도 향상되었다. 이러한 새로운 낙석방지울타리를 도로공사 절취사면 현장에 성공적으로 적용하였다. 그 결과, 시공성은 기존에 비해 별차이가 없는 것으로 나타났으나 미관상 전체적으로 심플하고 깨끗한 이미지를 연출할 수 있었다. 경제성 분석결과에 있어서는 전체 건설비용에 있어 기존 대비 약 20% 정도 절감되는 것으로 나타났다.